Trigger Pull: The trigger pull on the Bolt Airsoft B4A1 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto.
Accuracy: I tested the B4A1 Airsoft rifle by putting around 10 rounds into a target from 30 feet with .36 gram Airsoft 6mm BB's while using a semi rested position (sand bag in the front - standing in the rear). I used a non-magnified red dot scope for this test rather than using the built in iron sights. I got very good result in semi auto and even with the recoil making my sights jump around a bit in full auto still stayed well centered on target and got about a 1.5 inch group in both semi and full auto. My chronograph testing with lighter .20 gram BB's resulted in a 421 fps 5 shot average.
Build Quality: The Bolt Airsoft B4A1 Metal AEG Carbine is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual Colt M4. The only plastic or nylon components are the stocks and the grips and perhaps some internal parts. I found the adjustable stock and magazine tolerance to be tighter than my King Arms M4A1 I previously reviewed which showed the Bolt B4A1 had a bit higher quality in the workmanship, for the most part the fit and finish was very good!
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS B4A1 Carbine is another great example of an Airsoft Carbine based on the Colt M4 platform. It is an AEG but because of the BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine . What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt B4A1 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real M4 and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel M4.
Great attention to detail with lots of working parts.
All Metal upper and lower receiver, lots of metal parts throughout.
Semi auto & full auto selectable.
High capacity 300+ round magazine.
Removable carry handle with Weaver/Picatinny rail underneath.
Nice high 420 real FPS.
Extremely accurate for plastic BB's.
Fully adjustable sights with two position Peep sights.
6 position adjustable stock.
Easy access to internal hop-up system.
Realistic Blowback Recoil system (BRSS) for a very believable shooting experience!
Cons:
May not get off as many shots per battery charge as a traditional AEG because of the Bolt Recoil Shock System.
Does not come with battery or charger but most higher end AEG's also do not.
Not yet readily available in Canada, maybe we can change that :)
Comments:
The Bolt Airsoft B4A1 Blowback Airsoft Carbine is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil which up until now was really only provided by Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very good and you just have to love the M4 platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. I like mine as is with my addition of a riser and Red Dot and if I every get a chance to get out for a skirmish this will be my weapon of choice for sure!
I was going to put these two very nice EKOL Dicle 9mm P.A.K. Front Firing Blank Pistols up in the Canada Replica Airguns Store at a preset price but after viewing the condition and the fact that I have had a lot of people asking about blank guns being available, I decided to put them up as silent auction items instead, I kind of wanted to show them off in a video ;)
They are both in "as new" condition, one has never been shot, the other has had a handful of rounds through it, to be honest I can not tell which is which? So basically they are both in "new condition".
Both EKOL Dicle's are being sold with customized Hogue grips but I will include the original grips with them. Both come in the original cases and with the flare adaptors.
To place a bid to purchase one or both of these very nice EKOL Dicle Blank Pistols, you will need to Email Me Here with your highest bid. I will contact the winning bid at the end of the auction and send them a PayPal request for the total amount including $17.99 Shipping/Handling along with their local tax rate. The winner will have till the end of the day to pay or I will move on to the next highest bidder.
This auction will conclude on Friday November 16th Midnight so act fast!
Enjoy my YouTube Video showcasing the EKOL Dicle twins:
I got a few sample products I wanted to quickly share with everyone :) First off Bolt Airsoft, a Taiwanese based company, sent me one of their B4A1 (M4A1 Copy) AEG Airsoft rifles featuring BRSS - (Bolt Recoil Shock System) which has Blowback with simulated recoil.
The Bolt B4A1 is designed after the M4A1 and looks and works like most AEG Airsoft rifles giving you sustained performance and the use of high capacity magazines but Bolt has added their BRSS - (Bolt Recoil Shock System) which gives you the feedback and recoil you would normally only get with a true GBB (Gas Blow Back) Airsoft gun.
I will be doing a full review very shortly so watch for it!
I also received from ASG (Action Sport Games) a few Mock Airsoft Suppressors, all of them are B&T (Brügger & Thomet) derivatives. It was nice that they sent me the version (MP9 QD) that fits perfectly on my ASG/KWA MP9. The other tow are the ROTEX-IIIA and ROTEX-IIIA Compact that fit perfectly on to a standard flash hider and even include one with them.
Check out my Vimeo Preview Video of these Review items from Bolt Airsoft and ASG:
As with most new items I pickup, I like to share them with everyone. I am checking into some more ROHM blank guns, an RG-59 and RG-88, the RG-59 is a lot like the ROHM RG-56 .22 caliber blank revolver I sell in the Canada Replica Airguns Store but in .380 caliber and the one I show off here is a 5 shot two-tone model. Other than that they use the same frame and mechanical parts throughout.
I also received a black/blued ROHM RG-88 which is kind of like a Walther PPK in design, it field strips the same, has a similar safety setup and even has a similar size and look to it although it is definitely not a replica of a Walther PPK. I am impressed with the overall quality of the ROHM blank guns, material used, fit and finish is very good.
Lastly, I acquired a pre-owned Umarex CP99 CO2 Pellet Pistol from a customer of mine. It is in pretty much in new condition and is one of the Umarex guns I was missing in my collection and have been looking to add. The Umarex CP99 is a pretty good replica of the Walther P99 and uses the standard Umarex metal 8 shot rotary magazines and shares the same CO2 grip fed magazine as the CPSport. The CP99 is German made so it's not one of the lower cost Umarex pistols out there but you do get what you pay for ;)
For my Canadian Blank Gun collectors, I'm not going to list these ones as Silent Auction items this time around so if you're looking for an EKOL blank gun, I have one of each of the following versions for sale:
Take aim and fire with "The gun that helped to change the world". The Thompson Military M1A1 AEG is a battlefield weapon with a serious attitude. This beautiful gun is a fully licensed 1:1 scale replica of a real Tommy gun, and features a full metal body with artificial wood grain finish, a 60 Rd plastic magazine, and a shot velocity of 500 fps (using .20g BBs). The M1A1 also features an adjustable BAXS System for increased power and shooting accuracy. Airsoft enthusiasts will love the stunning classic era looks and awesome semi/fully automatic firepower of the Thompson Military M1A1 AEG. Do not miss this gun! Recommended for use with high quality .25g BBs.
Model:ME Ranger (1873 Colt 45 Single Action Army).
Materials: Mostly Metal with wood grips.
Weight: 2.2 pounds.
Barrel: Cylinder venting with fully plugged barrel. (No Red Tip)
Propulsion: Gun powder.
Action: Single action only.
Ammunition Type: .380 Crimped.
Ammunition Capacity: 6 rounds.
FPS: N/A.
Trigger Pull: The trigger pull on the Bruni ME Ranger Colt 45 Single Action Army Revolver is very light as it is a single action revolver and most of the effort is done by pre-cocking the hammer. All you are doing is releasing the hammer which with the ME Ranger is nice and light with next to no creep.
Accuracy: NA.
Build Quality: The overall build quality of the Bruni ME Ranger is nice an believable. It has good weight to it and the finish is not perfect but you would not expect and Single Action Army styled revolver to be perfect. All the mechanical parts felt tight and functioned perfectly for me.
Realism: The Bruni ME Ranger Blank Revolver is a pretty decent replica of a real Colt 45 Single Action Army Revolver in terms of size, weight and most general appearances. It does lack the 45 caliber larger more open Cylinder holes as it is chambered in .380 caliber but you can only see this when looking from the forward position of the ME Ranger. My version also had the plugged barrel so all flame and gasses emit from between the cylinder and the back of the barrel, it would be nice to un-plug this barrel so some of the gasses and flame would come out the front of the barrel.
Purchase from: A private collector.
Pros:
Well made, materials fit and finish is all very good.
True to the original 1873 Colt Single Action Army Revolver.
Real wood grips.
Nice light single action trigger.
Made in Italy.
Cons:
Not fornt venting.
9mm P.A.K. blanks do not fit - too long.
Wood grips are a bit bland.
Comments:
As my first replica Old West Single Action Blank Revolver, it is a nice addition to my collection. It would make an awesome prop for any cowboy or cowgirl costume, maybe I can convince my wife to go as a cowgirl this year for halloween ;) Overall I really like the Bruni ME Ranger and I plan to perhaps open the barrel up so that I get a more realistic shooting experience with flames and smoke coming out the front of the barrel. That and perhaps some work on the grips to give them a more rugged and weathered look.
My Vimeo Full Video Review for the Bruni ME Ranger Blank Revolver:
I haven't had a blank gun Silent Auction for a few months now. Not too many people are willing to give theirs up here in Canada. Today I am featuring two very good condition EKOL blank guns, both front firing and in Satin finish and both full size and full weight 15 round double stack semi auto shooters. The EKOl Dicle is semi auto only while the Jackal Dual has a selector switch for shooting in semi auto or full auto. The EKOL Dicle comes with it's original hard shell case, manual and flare adaptor while the EKOL Jackal Dual does not have a case but does come with a flare adaptor.
Remember the Silent Auctions for blank guns are primarily for my Canadian customers as blank guns are very hard to come by here in Canada. If you are interested in bidding on one or both of these guns, please send me an email with your highest bid to mike@replicaairguns.com. This Silent Auction end date is August 24th at midnight so get your bids in ASAP.
If you are US based you can order a front firing EKOL Blank gun from my US Replica Airguns Store.
You can also check out my full reviews on both these guns:
Trigger Pull: The trigger pull for both ROHM Le Petit and Little Joe blank revolvers in single action is nice and light. The action for both blank revolvers is very solid so cocking both guns requires a firm grip, the ROHM Le Petit also allows for double action shots and while it takes some force, the mechanics are very smooth and you can really feel the German quality in the hammer and trigger.
Accuracy: NA.
Build Quality: Even though both revolvers are made as blank/signal guns and do utilize scaled down metals (not high pressure gun steel), they are made very well and many of the internal mechanical parts, pins and screws are solid steel. The fit and finish is excellent and both guns worked flawlessly for me in my testing.
Realism: Both ROHM blank Revolvers are derivatives of similar real guns (Freedom Arms and RG 22) but again have been made from the ground up to be blank guns and can not be converted in any way shape or form to fire live ammo. The quality and feel is very believable, they also both fire out the front of the barrels and can shoot 15mm flares with the required flare adaptors attached.
Can also shoot 15mm flares with appropriate flare adaptor attached.
Come in gift box with cleaning rod and manuals (Le Petit RG-56 also comes with flare adaptor)
Cons:
Real wood grips would have been a nice touch but could be added later.
Little Joe does not come with a flare adaptor.
Comments:
We now have some blank guns that seem to be somewhat available in Canada... At least for now! And even though some of the other blank guns I was selling may have been more to the liking of the folks that where looking for a semi auto styled blank gun, the good news is both of these guns are very high quality and revolvers in general are very dependable. I also like the fact that both of the ROHM Blank Revolvers are fairly compact and so if you want to take them with you out on a hike or in the back country, they will not take up much room or add too much weight, but are still ready if required to scare off something bigger or more dangerous than you!
After what has been a very long absence of any new Blank (Flare Guns) in the Replica Airguns Canada Store, I managed to find a supplier for some very high quality German made .22 caliber compact revolvers. These two ROHM (RÖHM) blank revolvers are almost all metal with the exception of the grips and for their size are very hefty. The ROHM Le Petit RG-56 and Little Joe both come in a nice gift box with the manual and cleaning rod while the larger RG-56 also included a flare adaptor.
RÖHM Le Petit RG-56 .22 Blank Revolver:
The RÖHM Le Petit RG-56 22 Blank Revolver is a very high quality German made almost all metal blank gun that uses affordable .22 caliber acorn blanks. It is very compact, front firing and has an 7 shot cylinder. The RG-56 comes presented in a gift box with a manual, flare adaptor and cleaning rod.
Mostly metal construction
German made
.22 caliber acorn style blanks
7 shot capacity
Single & double action
Hefty 472 grams - 1 pound
Flare adaptor included
Cleaning rod included
Comes in a gift box
RÖHM Little Joe Ultra Compact .22 Blank Revolver:
The RÖHM Little Joe Ultra Compact .22 Blank Revolver is a very high quality German made almost all metal super compact blank gun that uses affordable .22 caliber acorn blanks. It is ultra compact, front firing and has a 5 shot cylinder. The RÖHM Little Joe comes presented in a gift box with a manual and cleaning rod.
The video is just a quick preview but you get to see the guns up nice and close and at the end I also show off my 9mm bullet Casing Ear Bud Headphones and talk a bit about what I like about them.
Without further ado here is My YouTube video featuring the Thompson M1928 Submachine Gun, ICS SIG SG-551 SWAT and 9mm Bullet Digital Stereo Earbuds:
The Thompson M1928 Chicago Style 1928 Submachine Gun with Drum Magazine is an awesome weapon that delivers semi & fully automatic fire at outstanding velocities in the battlefield. This gun has a polished full metal body that recreates the awesome look and feel of a real Tommy gun. The gun features a metal gear box & steel bushings, a high-capacity 450 rd drum magazine and a shot velocity of 390-450 fps (using .20g BBs).
The front charging handle allows you to control the gun and an adjustable BAXS shooting system improves the accuracy of the gun when shooting from long distances. Own your enemies and order today! This rifle also Includes: 8.4 V 2000 mAh Ni-CD battery, 300 mah charger (6.5 hrs charge time), cleaning rod & manual.
We just got in a new Field ready Airsoft AEG rifle, the Cybergun ISC SG-551 SWAT version. Get in on our introductory sale price!
The Cybergun ICS SIG SG-551 SWAT offers hardcore performance in a lightweight and compact package. Manufactured in Taiwan under licensed from Cybergun this rifle features full SIG trademarks engraved into its receiver.
With a stamped aluminum upper receiver and cast lower, the SG-551 weighs over a pound less than a KWA M4 while retaining the same strength and rigidity. Complete with a fiber composite handguard and pistol grip you can feel the quality of this rifle as soon as you pick it up. Its side folding skeleton stock locks firmly into open and closed positions making this rifle highly versatile in both indoor and outdoor scenarios. It features a centrally located magazine release and ambidextrous selector levers allowing for left or right handed use. One cool thing about these ICS SIG series rifle is the functioning bolt catch. Pull the bolt back all of the way and it will lock open allowing you to easily adjust the rifle hop-up without needing a third hand to keep the bolt back. Once you are done just flip the bolt release and the bolt flies forward with a nice metallic ring. Other features include a folding trigger guard for use with thick gloves, adjustable front sight complete with hood and changeable long/close range sight post, rotary rear sight with four adjustable apertures as well as windage and elevation adjustments.
Its battery is housed in the handguard which has enough room to hold an 8.4v or 9.6v AK Stick Type battery.
I have a rare EKOL LADY blank gun for you today listed as a silent auction item, this blank gun is a front venting model so the barrel is semi-plugged but all the flames and smoke vent out the front of the barrel like a traditional gun.
This EKOL LADY 9mm P.A.K. Blank Pistol in Satin is previously owned, it has been fired but is in very good condition. It comes in a hard shell foam lined plastic case.
Please submit your silent auction offers to me by no later than June 27th midnight! (Silent auctions are for our Canadian customers looking to by blank guns in Canada) participants can send me an email with their top bid on the item listed and the highest bid wins this auction). *Local tax plus shipping & handling will be added.
Good luck to all participants!
If you reside in the US, you can also buy the EKOL Firat new from us in our US Replica Airguns Store.
I have been hinting about an even bigger Canada sale on the King Arms Colt M4A1 Metal AEG Airsoft Rifle and here it is - now $100 OFF the regular price (Canada Store Only) so don't wait as I'm not sure how long this sale will last...
I just received some of my ASG Airsoft guns in my BC location and wanted to make an update video for you so you can see them up close and perhaps see how they stack up against their Airgun counterparts. Keep in mind many of my ASG guns are only available in the Canada Replica Airguns Store, we do have some ASG Airsoft guns for my US based customers but this time here in Canada I have more to offer my Canadian folks!
I am also super impressed with the high quality of the LMT Defender M4 Carbines, they are a serious bit of gear and have some very good heft to them, even more so than my full metal King Arms M4A1 I already sell and have done a full review of, not to take anything away from the Kings Arms product as it is very good at its price point.
I also received my first sniper rifle and have played around with it a bit to see what it is capable of. I added a bipod to the front and a 3x9 power scope as the ASG AW .308 comes pretty bare bones but ready for all you can throw at it. I can say it likes heavier Airsoft BB's, as the .20 gram ones I started with seemed to fly off in all directions due to the high velocity, even stepping up to a .25 gram BB tightened my group up significantly at 30 feet. I have heard this rifle really prefers heavy Airsoft BB's so I plan do do my review based on that information.
Enjoy my Vimeo Video Update focusing on the new ASG Airsoft lineup.
The STI Duty One 1911 Non-Blowback Airsoft Pistol is a full size replica of the actual STI Duty one 1911 pistol which is a modernized and upgraded version of the original classic Colt 1911. You will find features like; an integrated weaver rail for lasers and tactical lights, high rise beavertail grips, a unique serial number on each air pistol and STI licensed markings. (BUY NOW)
The ASG AW .308 very powerful spring operated Airsoft Sniper Rifle and has licensed Accuracy International AW .308 markings. Out of the box it shoots close to 2 joule and weights almost 7 pounds with its solid metal construction. The Sportline AW .308 has adjustable Hop-Up for accuracy and top rail for mounting a scope. (BUY NOW)
The ASG LMT Defender R.I.S. is a classic carbine with a few modifications. The normal front guard has been replaced with a full rail interface system (R.I.S.), that gives you plenty of opportunities to mount accessories. As the normal battery space is used by the R.I.S. the wiring to the battery goes back to the stock. The stock is a special sopmod stock with two compartments to house the battery. The functionality is similar to the other LMT ProLine models – Adjustable hop up, 1.5 joule power and semi & full auto. (BUY NOW)
The Proline (PL) range of products, are high-end products, targeted at regular players, players who want to have better than average Airsoft gun and Milsim/teamplayers. The Proline models can be modified and upgraded.
Two well known firearms and accessory manufactures have joined forces to create this beauty of a Proline Airsoft AEG. The full metal Defender4 Carbine licensed by LMT upgraded with the S.I.R. rail system licensed by A.R.M.S.. A Selective Integrated Rail system (S.I.R.) offers a wide variety of options to mount tactical accessories. Quick and handy flip-up iron sights are mounted on the S.I.R. Strong and well built with what is probably one of the best out-of-the-box gearboxes, heavy reinforced with 8 and 9 mm bearings, steel gears, and ball-bearing spring-guide as well as an upgraded cylinder set. It can handle Li-Po batteries and shoots 1.5 joule (120m/s/394 fps) in semi- and full-auto mode with Easily adjustable Hop-Up. (BUY NOW)
The Proline (PL) range of products, are high-end products, targeted at regular players, players who want to have better than average Airsoft gun and Milsim/teamplayers. The Proline models can be modified and upgraded.
I have another EKOL Firat Magnum blank gun for you today listed as a silent auction item, this one is a top venting model so the barrel is plugged and all the flames and smoke vent out the top of the barrel, not the front. The EKOL Firat has always been a popular seller here in the Replica Airguns Store.
This EKOL Firat Magnum 9mm P.A.K. Blank Pistol in Gloss Black is previously owned but has low usage and is in very good condition. It comes in a hard shell plastic case with the manual, and field stripping key.
Please submit your silent auction offers to me by no later than June 5th midnight! (Silent auctions are for our Canadian customers looking to by blank guns in Canada) participants can send me an email with their top bid on the item listed and the highest bid wins this auction). *Local tax plus shipping & handling will be added.
Good luck to all participants!
If you reside in the US, you can also buy the EKOL Firat new from us in our US Replica Airguns Store.
Trigger Pull: The trigger pull on the Umarex SW1911 S is actually fairly heavy which I found a bit surprising because it is a single action only gun. I found myself thinking a few times that the gun may have misfired but realised that I just needed to pull the trigger a bit firmer. This can be good in that the gun will not easily or accidentally go off and since accuracy is not a factor it is not a big deal.
Accuracy: NA.
Build Quality: The overall build quality of the SW1911 S is fantastic. It is one of the nicest blank guns in terms of overall build quality and finish quality. The tolerances are very tight and the quality of the workmanship is top notch. When holding the Umarex SW1911 it has a lot of mass to it and feels just like a real 1911 in the hand. This blank pistol is made in Germany!
Realism:The Umarex SW1911 S is a replica of a Smith and Wesson 1911 semi auto pistol but I could not find an exact match to a specific model they currently make. It is licensed and branded by Smith & Wesson and in terms of looking like a real steel gun it is bang on with the exception of the exhaust notch that is cut into the top of the slide. Interestingly enough I think Umarex may have not even needed to cut out this notch as my slow motion video shows that all the burn off happens before the slide even starts to move.
Very well made, materials fit and finish is all very good.
Two-tone finish looks very nice.
Very true to the original 1911 - (A1 styled).
Love the nice rubber wrap around grips.
I was able to fit 10 rounds in the magazine (2 extra)!
German made quality.
Cons:
Top venting.
Notch cut out of slide takes away from the realism a bit.
Magazine can be a bit tuff to get in (pressing the magazine release helps).
Heavy trigger pull on mine.
Comments:
Even though the Umarex SW1911 S had a few shortcoming like being a top venting gun, having the notch cut out of the slide and perhaps a bit heavy of a trigger, I still really like it! The quality is evident throughout this fine German made blank gun and you can just tell it's made right. This is also my first true replica blank gun as it is fully licensed by Smith & Wesson, something that has been lacking in all my other blank guns because of our Canadian importation laws. I really wish I could get my hands on some more "replica blank guns" as I don't mind giving up the front firing for top venting to obtain a blank gun that is a true replica.
Photo of ZORAKI 917 Removed by Request from Glock "Renzulli Law Firm"
All references, photos and video claiming that any item in this Review/Video looks like a Glock or is a Replica of a Glock in any way shape or form have been removed from this post as requested by Glock"Renzulli Law Firm"
When ever I can get my hands on some blank guns at a realistic price or perhaps a trade that works for both parties, I generally try to make it happen. And if they are guns that I don't have in my collection, well they go directly into my collection so please no offers from fellow Canadians as I tend to hold onto my more rare or hard to acquire Canadian replica guns pretty firmly! .
Both of these 9mm P.A.K. Blank shooting guns are not brand new but they are in very good condition and it's hard to even say it they have been shot or not? My new Zoraki Mod. 917 as you can see, is styled very closely after the NAME REMOVED and so much so that all new version sold in North America must have "This is not a Glock" engraved on the right side frame of the receiver in order to be sold. Mine however was purchased before this requirement :) UPDATE: NO LONGER BEING SOLD IN NORTH AMERICA.
Photo of ZORAKI 917 Removed by Request from Glock "Renzulli Law Firm"
My Umarex SW1911 S is licensed by Smith & Wesson which makes it pretty hard to get in Canada becasue for a very long time we have not been allowed to import any replica guns and since it is licensed it makes it a true replica and would normally be stopped at the boarder. You may own replicas in Canada without a said license but you need to make sure they are stored and handled as defined by the requirements outlined in the Canada Firearms Act.
