View fullsize

The Umarex T4E TP50 Gen 2 continues to impress as one of the more powerful and practical compact less-lethal pistols currently available. In this field test review, I tested the all-black version using .50 caliber rubber-steel core rounds to see how it performs in terms of velocity, energy, and real-world accuracy. The black version is essentially the same as the orange-marked variant, just marketed a bit differently, with a more tactical appearance that may appeal to those looking for a serious training or home defense-style option.

For ammunition, I used the steel-core rubber balls rather than standard solid rubber rounds. These projectiles are slightly heavier and seem to carry noticeably more energy downrange without sacrificing too much velocity. In my opinion, they are probably some of the best ammunition choices for these types of pistols if maximum impact energy is your goal.

Velocity testing through the chronograph produced some very impressive numbers. The TP50 Gen 2 delivered readings of 319 FPS, 304 FPS, 310 FPS, 300 FPS, and 308 FPS, averaging just over 308 feet per second. With the steel-core rubber rounds weighing approximately 2.7 grams, the pistol produced roughly 12-13 Joules of muzzle energy using the Steel Core Rubber Balls but would have been closer the projected 15 Joules with all Rubber Balls, which is extremely respectable for a compact CO2-powered .50 caliber launcher. You can really hear and feel the power when firing this pistol, and it even generates noticeable recoil-like kick during shooting.

View fullsize

Accuracy testing was performed from 30 feet downrange using the six-round internal magazine. Paintball-style projectiles are naturally less precise than pellets or BBs due to their softer construction, surface ridges, and aerodynamic inconsistencies, but the Umarex T4E TP50 Gen 2 still delivered surprisingly solid grouping performance. After adjusting my aim slightly low due to the pistol shooting a little high initially, the remaining shots grouped well into the center portion of the target and produced clean, sharp holes through the paper target with about a 3 inch grouping.

In practical terms, this pistol clearly delivers enough impact energy to strongly discourage an attacker or aggressive threat. The steel-core rubber rounds hit extremely hard, especially considering the combination of high velocity and projectile mass. While heavy clothing would certainly absorb some impact, anyone wearing lighter clothing would absolutely feel these rounds. The all-black appearance also adds to the realistic tactical styling, which alone could act as a deterrent before a shot is ever fired.

Overall, the Umarex T4E TP50 Gen 2 proved to be accurate enough for close-range defensive-style use, delivered excellent power, and offered reliable operation throughout testing. The trigger feels good, the pistol handles nicely, and the performance with steel-core rubber ammunition was impressive across the board. For anyone looking for a compact CO2-powered less-lethal launcher with strong energy output and solid build quality, the TP50 Gen 2 is definitely worth considering.

You can find the Umarex T4E TP50 Gen 2 and other Airguns, BB guns, Airsoft guns, Pellet guns, Blank guns, and accessories at:

• Buy the Umarex T4E TP50 Gen 2 CO2 Paintball Pistol in Canada

• Buy Paintball Guns in the US

View fullsize

First Look & Overview

In this table top review, taking a detailed look at the Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol, a modern, competition-style airgun replica that closely mirrors its real steel counterpart. This model stands out with its aggressive styling, compensated muzzle, and optics-ready slide, making it one of the more premium-looking pellet pistols currently available.

This is a pellet-only airgun with blowback action, designed more for realism and handling than raw velocity. If already familiar with the Sig Sauer M17 pellet pistol, this one shares a lot of mechanical similarities, including the magazine system.

Specifications

• Caliber: .177 Pellet

• Action: Semi-auto, blowback

• Magazine: 20-round belt-fed rotary system

• Power Source: 12g CO2 (tool-free cam lever system)

• FPS: Claimed 340 FPS

• Weight: ~2.3 lbs

• Overall Length: 8.5 inches

• Barrel Length: 4.6 inches (rifled)

• Construction: Metal slide, polymer frame

• Sights: Fixed white dot front and rear

• Optics Ready: Yes (SIG Air RMR compatible)

• Rail: Picatinny accessory rail

• Safety: Ambidextrous manual safety

View fullsize

Build Quality & Design

The Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol delivers a solid mix of metal and polymer construction. The metal slide gives it realistic weight and feel, while the polymer frame helps keep things balanced. At around 2.3 pounds, it has a substantial presence in hand without feeling overly heavy.

The grip features enhanced texturing along with a flared magwell, adding to both aesthetics and usability. The slide includes light porting and is optics-ready, allowing for easy installation of a SIG Air RMR red dot.

One standout visual element is the compensated muzzle, which adds to the competition-style look. However, it also impacts field stripping, you’ll need to remove it to fully disassemble the slide.

View fullsize

Magazine & CO2 System

This pistol uses a 20-round belt-fed rotary magazine, which is housed within a drop-out mag body. Loading is straightforward:

• Remove the rotary belt insert

• Load pellets into each chamber

• Reinsert into the mag

CO2 is loaded using a tool-free cam lever system, which is fast and convenient compared to traditional screw-in designs.

Important note: the magazine needs to be firmly seated. A light insertion may not lock it properly, and due to the weight, it could fall out if not fully engaged.

Also worth noting, while the outer mag housing has some polymer components, the internal structure is mostly metal. Still, avoid dropping it on hard surfaces.

View fullsize

Handling & Controls

• Ambidextrous safety works from both sides, though visual indicators are only clearly marked on one side

• Trigger feels closer to double-action due to the rotary magazine indexing

• Slide cycles with blowback but does not lock back when empty

• Takedown lever is present, but full disassembly is limited by the compensator

The trigger has a solid feel and requires deliberate pull due to the indexing mechanism. This is normal for belt-fed pellet systems.

View fullsize

Sights & Optics

The pistol comes with fixed white dot sights, which are effective for quick target acquisition. However, they are not adjustable.

For those wanting more precision, the pistol supports SIG Air RMR optics, replacing the rear sight with an included plate.

Performance Expectations

The claimed velocity is 340 FPS, which is typical for blowback pellet pistols. Expect slightly lower speeds with lead pellets (recommended) compared to alloy pellets.

Blowback operation will also consume more CO2 than non-blowback models, trading efficiency for realism.

If looking for a performance reference, similar results can be expected to the Sig Sauer M17 pellet pistol due to shared internals.

View fullsize

Pros

• Excellent replica accuracy of the P320 Spectre Comp

• Realistic blowback with metal slide

• Good weight and balance (~2.3 lbs)

• 20-round high-capacity pellet magazine

• Tool-free CO2 cam lever system

• Rifled barrel optimized for pellet shooting

• Optics-ready (SIG Air RMR compatible)

• Flared magwell and enhanced grip texture

• Picatinny rail for accessories

• Magazine compatibility with M17

Cons

• Lower FPS compared to non-blowback pellet pistols

• Higher CO2 consumption due to blowback

• Fixed (non-adjustable) sights

• Pellet-only (no BB capability, though this protects rifling)

• Slide does not lock back when empty

• Field stripping requires compensator removal

View fullsize

Final Thoughts

The Sig Sauer P320 Spectre Comp pellet pistol is a strong option for anyone prioritizing realism, handling, and modern styling over raw power. It delivers a premium look with solid functionality, especially for training, backyard shooting, or collectors wanting a high-end replica.

While not the most powerful pellet pistol available, it excels in design, usability, and realism, especially if already a fan of the P320 platform.

For those in Canada, availability may already be live, with US availability likely to follow.

• Buy the Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol in Canada

• Buy Sig Sauer Airguns in the US

View fullsize

In this review, we are looking at two crossbows that honestly shouldn’t really be compared, but that’s exactly why this comparison is interesting. On one end, we have the Steambow M10, a compact, magazine-fed, fast-shooting crossbow built for fun, training, and high repetition shooting. On the other, the CenterPoint AT400, a full-size, high-powered compound crossbow designed for serious hunting applications.

Aside from both launching bolts/arrows, these two platforms sit at completely opposite ends of the spectrum. The goal here is not to declare a winner, but to help you decide which one actually fits your use case, or if you might want both.

Key Differences Overview:

Steambow M10

The Steambow M10 is a compact repeating crossbow designed more for fun, training, and high-volume shooting. It uses a magazine-fed system that can hold 10 bolts, allowing for very fast follow-up shots. Depending on the limb setup, it can reach speeds of up to around 200 FPS and produce approximately 10 to 15 foot-pounds of energy. Its lighter draw weight options and easy cocking system make it beginner-friendly and much less physically demanding to use. Overall, the M10 is best suited for target shooting, casual use, and potentially small game with the right setup.

CenterPoint AT400

The CenterPoint AT400 is a full-size compound hunting crossbow built for serious power and hunting use. Unlike the M10, it is a single-shot platform that focuses on accuracy, penetration, and range rather than fast repeat shooting. It sends arrows downrange at about 400 FPS and delivers close to 150 foot-pounds of energy, putting it in an entirely different class. With its roughly 200-pound draw weight, it requires much more effort to cock and reload, usually with a rope or crank system. This makes it better suited for medium to large game hunting, where power and shot placement matter far more than speed.

Side-by-Side Summary

If you want something lightweight, compact, fast, and easy to shoot often, the Steambow M10 is the better fit. If your main goal is hunting and you need maximum power, longer range, and serious downrange performance, then the CenterPoint AT400 is clearly the more appropriate choice. Even though both are crossbows, they are built for very different types of users and very different shooting experiences.

Power & Performance

The biggest separation between these two comes down to raw power.

• The Steambow M10 delivers up to about 10–15 foot-pounds of energy, depending on limb configuration and bolt weight. It’s comparable to higher-end airguns or paintball-level power.

• The CenterPoint AT400, by contrast, produces close to 150 foot-pounds of energy and launches arrows at around 400 FPS.

That’s not a small difference, it’s an entirely different category.

Real-world comparison:

• M10 = backyard shooting, small game potential

• AT400 = deer, and potentially even elk with proper shot placement

This is essentially the difference between a BB gun vs a hunting rifle in terms of role and impact.

View fullsize

Shooting Experience:

Steambow M10

• Magazine-fed (10 bolts)

• Extremely fast follow-up shots

• Break-action style cocking (very quick)

• Great for drills, repetition, and skill building

• Minimal effort required

You can realistically fire 10 shots in about 10 seconds, making it a very engaging and fun platform.

CenterPoint AT400

• Single-shot system

• Requires rope cocking or crank system

• Significant physical effort (200 lb draw)

• Slow reload (often 30–60+ seconds)

This is a deliberate shooting experience, not something designed for volume or speed.

Use Case Breakdown:

Steambow M10 – Best For…

• Backyard shooting (with proper backstop)

• Target practice

• Tactical-style drills

• High repetition training

• Casual and frequent use

• Lower-cost shooting (especially with rubber ball version)

View fullsize

You can even use:

• Rubber balls (low cost, reusable)

• Lightweight bolts

• Indoor-friendly setups (with proper safety)

CenterPoint AT400 – Best For…

• Hunting (deer and potentially larger game)

• Long-range accuracy

• Maximum penetration and power

• Purpose-driven shooting

This is not a casual-use product, you typically bring it out when it matters.

Ease of Use & Physical Demand:

Steambow M10

• Very easy to cock (even at lower draw weights)

• Beginner-friendly

• Lightweight (~compact platform)

• Minimal fatigue

View fullsize

CenterPoint AT400

• High effort required

• Needs cocking tools (rope or crank)

• Physically demanding

• Slower workflow between shots

Key takeaway:
Anyone can pick up and use the M10 easily. The AT400 requires more commitment, strength, and practice.

Size & Portability

Steambow M10

• Compact and lightweight

• Can be partially disassembled easily

• Backpack-friendly

• Ideal for mobile use

CenterPoint AT40

• Large, fixed structure

• Not easily transportable without a case

• Designed for field carry, not casual portability

Ammo & Cost of Ownership:

View fullsize

Steambow M10

• Bolts are smaller and cheaper

• Rubber ball version = extremely low cost

• Less wear and tear overall

• High reusability

CenterPoint AT40

• Arrows are larger and more expensive

• More prone to damage/loss at high speeds

• Requires maintenance and replacement over time

Value Consideration:

Interestingly, both fall into a similar price range (~$400–$500), but value depends on usage frequency:

• M10 → Likely used often → Higher practical value

• AT400 → Used less frequently unless hunting regularly

If something sits unused, its value drops regardless of price.

View fullsize

Who Should Buy Each?

Choose the Steambow M10 if you…

• Want fun, fast shooting

• Plan to shoot frequently

• Prefer low effort and ease of use

• Don’t need high power

• Enjoy tactical or training-style shooting

Choose the CenterPoint AT400 if you…

• Are hunting (especially deer or larger game)

• Need high power and penetration

• Value accuracy and range

• Don’t mind slower reload times

• Are comfortable with physical effort

View fullsize

Final Thoughts

These two crossbows are not competitors—they are tools for completely different jobs.

• The Steambow M10 is about frequency, fun, and versatility

• The CenterPoint AT400 is about power, precision, and purpose

If anything, this comparison highlights that you may not need to choose one over the other, you might actually benefit from having both ends of the spectrum covered.

If neither fits perfectly, then the real answer may be to look for something in the middle.

Where to Buy

Both of these crossbows (or similar models) are typically available through:

• Buy Steambow M10 in Canada

• Buy CenterPoint AT400 In Canada

• Buy in the US

View fullsize

In this table top review, we’re taking a look at the Umarex T4E TP50 Gen 2 CO2 Paintball Pistol, part of Umarex’s T4E (Training for Engagement) lineup. This version is marketed more as a tactical training pistol, while its nearly identical counterpart, the HDP50, is positioned toward home defense.

At first glance, the TP50 and HDP50 look almost identical. The main visual difference is that the TP50 comes in an all-black finish, while the HDP50 features an orange slide. Beyond that, the functionality, performance, and specs are essentially the same.

Key Features and Specifications

• Manufacturer: Umarex

• Model: T4E TP50 Gen 2

• Caliber: .50 caliber

• Power Source: 12g CO2 (quick piercing system)

• Action: Semi-auto, double action trigger

• Magazine Capacity: 6 rounds (internal inline magazine)

• Velocity: Rated up to 465 FPS

• Energy: Claimed 11 joules (can be higher depending on ammo)

• Barrel Length: ~4 inches

• Overall Length: ~8 inches

• Weight: ~1.5 lbs (0.7 kg)

• Construction: Polymer frame and slide with metal internals and barrel

• Safety: Integrated trigger safety

• Rail: Under-barrel Picatinny rail

• Sights: Fiber optic front and rear

View fullsize

Overview and First Impressions

The TP50 Gen 2 is a compact, .50 caliber paintball-style pistol designed for training, recreational shooting, and less-lethal applications. It has a solid feel in the hand, not too heavy, not too light, and resembles a full-size handgun profile, similar in size to a large-frame pistol.

Despite its polymer exterior, the internal components that matter, especially around the CO2 system—are metal, giving it durability where needed.

CO2 System (Quick Piercing Feature)

One of the standout features is the quick piercing CO2 system:

• Insert the CO2 cartridge (butt-first)

• Tighten the cap until snug

• When ready to use, give the bottom a firm “whack”

• A pin pops out on the back where you can see it to indicate the system is pressurized

This allows you to keep the pistol loaded but not activated, which is useful for storage or readiness situations.

View fullsize

Ammo Compatibility

The Umarex T4E TP50 Gen 2 CO2 Paintball Pistol supports a wide range of .50 caliber ammunition, including:

• Rubber balls

• Powder balls

• Paintballs

• Steel/rubber hybrid balls

• Pepper balls (limited availability in Canada)

Performance varies significantly depending on the weight of the projectile:

• Lighter rubber balls: ~450 FPS / ~13–15 joules

• Heavier projectiles: lower energy (down to ~7–11 joules)

View fullsize

What’s Included

• TP50 Gen 2 pistol

• Two tubes of 10 rounds each (powder + rubber balls)

• Barrel cleaning squeegee

• Instruction manual

• Cardboard packaging (blue “tactical pistol” branding)

View fullsize

Walkaround Highlights

• Fiber optic sights make target acquisition easy in various lighting conditions

• Textured grip and slide for solid handling

• Metal trigger with integrated safety

• Wide open barrel design

• Picatinny rail for adding lights or lasers

• Clear “Strike” marking for CO2 activation point

Overall, it’s a clean, functional design with a tactical look, especially in the all-black version.

View fullsize

Pros

• Compact size compared to other .50 cal pistols

• Wide variety of compatible ammo types

• Quick piercing CO2 system (very practical)

• Good power for its size (~11–15 joules range)

• Fiber optic sights improve usability

• Picatinny rail for accessories

• Realistic all-black tactical appearance

Cons

• Only 6-round capacity before reload

• Limited shots per CO2 (~3–4 reloads)

• Internal magazine (no quick mag swaps)

• Pepper ball ammo difficult to source in Canada

• Efficiency trades off for higher power

TP50 vs HDP50 (Quick Comparison)

• TP50: All black, marketed as tactical training

• HDP50: Orange slide, marketed for home defense

• Performance: Essentially identical

View fullsize

This difference is largely cosmetic and marketing-driven, so choosing between them comes down to preference and intended use.

Final Thoughts

The Umarex T4E TP50 Gen 2 CO2 Paintball Pistol is a solid, compact .50 caliber CO2 pistol that delivers respectable power in a manageable platform. It’s not designed for high-capacity shooting or efficiency, but rather for impact, simplicity, and versatility in ammo choice.

If you’re looking for a less-lethal option or a training pistol with realistic handling and solid performance, the TP50 fits that role well, especially if you prefer the more discreet all-black tactical look.

Where to Buy

• 🇨🇦 Buy the T4E TP50 in Canada: ReplicaAirguns.ca

• 🇨🇦 Buy the T4E HDP50 in Canada: ReplicaAirguns.ca

View fullsize

In this table top review, we’re taking a close look at the Air Venturi Annie Oakley Lil’ Sure Shot Spring BB Rifle. While this is technically a “table top” review, lever-action rifles like this are always a bit easier to show off in-hand due to their length and proportions.

This model fits into a long lineage of classic lever-action BB rifles, alongside well-known options like the Daisy Red Ryder and the Marlin variants from Crosman and Umarex. These rifles all share a similar concept, simple, spring-powered, lever-action BB guns designed for training, plinking, and beginner shooters, but each brings its own subtle differences in materials, styling, and features.

Key Specifications

• Model: Air Venturi Annie Oakley Lil’ Sure Shot

• Type: Lever Action Spring Piston BB Rifle

• Caliber: 4.5mm Steel BB

• Power Source: Spring (No CO2 Required)

• Velocity: Up to 350 FPS

• Magazine Capacity: 550 Round Internal Reservoir (Gravity Fed)

• Action: Lever Action

• Safety: Cross Bolt Safety

• Barrel: Smoothbore

• Stock: Stained Solid Wood

• Construction: Primarily Metal with Some Plastic Components

• Weight: Approx. 3.3 lbs

• Overall Length: ~36.25 inches

• Optics Rail: Removable Weaver/Picatinny Style Mount

First Impressions & Build Quality

The Annie Oakley Lil’ Sure Shot stands out with its classic Western styling, enhanced by engraved Annie Oakley branding on the wood stock. It’s a step above many entry-level BB rifles thanks to its real wood stock and metal lever, giving it a more authentic and durable feel compared to fully plastic alternatives.

Most of the rifle is metal and wood, though there are a few plastic components:

• Trigger

• Front sight (on the newer version)

• Adjustable portion of the rear sight

• Removable scope rail

Overall, it feels solid in the hands, lightweight, and well-balanced, especially for younger shooters or anyone new to lever-action rifles.

View fullsize

How It Works

This is a spring-piston, lever-action BB rifle, meaning:

• No CO2 or gas is required

• Each shot is powered by cocking the lever

• BBs are stored in a large internal reservoir

• You must tilt the rifle upward to gravity-feed BBs into position

With a 550-round capacity, you can shoot for quite a while before needing to reload, your arm will likely get tired before you run out of ammo.

Handling & Usability

This rifle is clearly designed with accessibility in mind:

• Lightweight (3.3 lbs) makes it easy to handle

• Shorter length and pull fits smaller shooters well

• Moderate cocking effort is manageable for beginners

• Lever action slows firing rate, adding a safety advantage for new users

Rifles like this are excellent for training because:

• They are easier to aim than pistols

• They encourage controlled shooting

• They are not overly powerful

Even for experienced shooters, these are simply fun and inexpensive for backyard plinking.

Sights & Optics

Out of the box, the Air Venturi Annie Oakley Lil’ Sure Shot Spring BB Rifle includes:

• Fixed front sight (plastic on newer version)

• Adjustable rear sight (elevation only)

One notable feature is the removable Weaver-style rail, allowing you to:

• Mount a red dot or scope

• Or remove it for a more traditional look

Keep in mind the rail is plastic, so care should be taken when mounting optics.

View fullsize

Comparison to Similar BB Rifles

This rifle sits in the same category as:

• Daisy Red Ryder – The original classic

• Umarex Marlin Lever Action – Slightly more adult-oriented design

• Crosman Marlin (older models) – Direct Red Ryder competitor

All of these:

• Use lever-action spring systems

• Have internal BB reservoirs

• Shoot in the ~300–350 FPS range

The Annie Oakley version distinguishes itself with:

• Better visual styling

• Wood and metal construction

• Optional optics mounting

New vs Older Annie Oakley Version (Key Differences)

If you come across different versions, here are the main distinctions:

Newer Version:

• Longer barrel

• Plastic front sight

• Larger loading port (easier to load)

• Metal Lever

• Brighter, more polished wood finish

View fullsize

Older Version:

• Shorter barrel

• Metal front loading system (rotating port)

• Metal front sight (more durable)

• Plastic Lever

• Slightly darker, more matte wood

Both should perform similarly, but the newer version is a bit more refined with that quality all metal lever.

Pros

• Lightweight and easy to handle

• Real wood stock and metal lever construction

• Large 550-round capacity

• No CO2 required (low maintenance and inexpensive to shoot)

• Removable optics rail for flexibility

• Classic Western styling with Annie Oakley branding

• Great for beginners and younger shooters

Cons

• Plastic front sight (new version)

• Lower power compared to CO2 rifles

• Rear sight only adjustable for elevation

• Slightly higher price than some entry-level similar BB rifles

• Less realistic than shell-ejecting lever-action models

Final Thoughts

The Air Venturi Annie Oakley Lil’ Sure Shot is a well-built, visually appealing lever-action BB rifle that blends classic styling with modern usability.

It’s ideal for:

• Beginners and younger shooters

• Backyard plinking

• Anyone wanting a simple, reliable and fun BB rifle

While it doesn’t aim for full realism like higher-end shell-ejecting models, it delivers where it matters, ease of use, affordability, durability, and fun factor.

Available at:

• 🇨🇦 ReplicaAirguns.ca

• 🇺🇸 ReplicaAirguns.us

Also check out ReplicaAirguns.com for additional articles, photos, and video reviews.

View fullsize

In this table top review, we take a close look at the Steambow B08 .68 Caliber Tactical Crossbow, a compact and versatile system designed for shooting rubber balls, paintballs, or foam projectiles. This model is particularly suited for controlled environments like indoor ranges (such as a sea can setup or even basement or backyard), thanks to its relatively moderate power and flexible ammunition options.

A full shooting test will follow separately, but for now, let’s break down the specifications, features, and what comes in the box.

Specifications

• Model: Steambow B08

• Caliber: .68 (rubber balls, paintballs, foam balls, etc.)

• System Type: Recurve crossbow

• Draw Weight: 35 lbs (standard included limb)

• Velocity: Up to 260 FPS (manufacturer claim)

• Energy: Approx. 7 ft-lbs (up to ~15 ft-lbs with stronger limbs)

• Magazine Capacity: 8 rounds (removable)

• Weight: Just under 4 lbs

• Length: 24.2 inches

• Width: 3.15 inches (body, excluding limb span)

• Height: 8.3 inches

• Materials: Fiberglass, metal, and polymer construction

• Stock: AR-style adjustable (6-position) with cheek rest and rubber butt pad

The B08 is distributed by Steambow GmbH (Austria) and is built on a modular platform compatible with other Steambow systems like the M10.

View fullsize

Key Features

Modular Platform

One of the standout aspects of the B08 is its modular design. The lower receiver is identical to the Steambow M10, meaning you can swap uppers to shoot either:

• .68 caliber balls (B08 upper)

• Crossbow bolts (M10 upper)

This gives users flexibility to adapt the platform for different uses.

Quick Change Limb System

The included 35 lb limb is easy to swap out:

• Secured by a single bolt

• Can be upgraded up to heavier options (up to ~120 lbs available)

• Allows tuning for power vs. ease of cocking

Magazine-Fed Repeater System

• 8-round removable magazine

• Spring-fed system with follower

• Auto-loading mechanism (not semi-auto, but fast cycling)

The system works by “breaking” or pulling back the stock, which:

• Cocks the string

• Loads the next round

• Prepares the trigger

Cocking Mechanism

• Shoulder-supported operation

• Pull stock inward to cock

• Very easy with 35 lb limb

• Allows relatively fast follow-up shots once familiar

Sighting System

• Fiber optic front sight

• Rear alignment via top trough channel

While simple, it works well for close-range shooting. However, the included Picatinny rails (top and bottom) allow for:

• Red dots

• Scopes

• Tactical accessories

Build & Ergonomics

• Polymer lower with reinforced components

• AR-style adjustable stock

• Adjustable cheek rest

• Rubber butt pad

• Included foregrip (user-installed)

Overall, the Steambow B08 .68 Caliber Tactical Crossbow has a solid, lightweight feel while still maintaining good handling characteristics.

What’s Included in the Box

The B08 comes well-packaged with multiple internal boxes and includes:

• Steambow B08 main unit

• 35 lb limb

• Foregrip

• 8-round magazine

• 25 “foam” balls (closer to hard nylon in feel)

• Protective shooting glasses

• Allen keys (for assembly and adjustments)

• String wax

• Extra string

• Mounting hardware

• Instruction manual

View fullsize

Note:
A small locking component for the upper assembly may come separate and is not clearly explained in the manual, but is required for proper function.

Operation Overview

• Load magazine with up to 8 rounds

• Insert magazine into front housing

• Cock by pulling stock inward

• Fire using single-action trigger

The ball is held in place by a simple groove and string system, guiding it forward during firing.

Performance Notes (Initial Impressions)

• Smooth and reliable operation

• Easy to cock with 35 lb limb

• Suitable for indoor shooting environments

• Compatible with various projectile types

Heavier limbs will:

• Increase velocity and energy

• Require more effort to cock

View fullsize

Pros

• Lightweight and compact (under 4 lbs)

• Modular system (compatible with M10 platform)

• Magazine-fed repeater design

• Easy cocking with included limb

• Quick-change limb system

• Picatinny rails for accessories

• Comes with useful extras

• Quiet operation

• Reusable ammunition options

Cons

• Higher price point

• No traditional rear sight included

• Learning curve for efficient operation

• Included limb may feel underpowered for some users

View fullsize

Final Thoughts

The Steambow B08 offers a unique blend of crossbow mechanics and tactical styling, combined with modular flexibility and relatively safe indoor usability. It’s especially appealing for users who want:

• A reusable ammo platform

• Quick follow-up shots

• Expandability with other Steambow systems

While the included 35 lb limb keeps it easy to use and accessible, upgrading the limb will unlock more performance potential for those looking for higher energy output.

Availability

Available through Replica Airguns:

• Buy the Steambow B08 .68 Caliber Crossbow in Canada

• US Archery Buying Options

A full shooting test and performance breakdown will follow in a separate review.

View fullsize

In this April 2026 unboxing, there’s a solid mix of power, realism, and variety straight out of the box. Even before opening it up, the size and weight of the package hinted that this wasn’t going to be a light or basic shipment. As usual, this is more of a first look and overview rather than a deep dive, with full tabletop and field test reviews coming later.

CenterPoint AT400 Compound Crossbow Kit (400 FPS)

The first item out of the box is easily the most substantial: an AT400 compound crossbow kit. This is not one of the smaller, backyard-friendly crossbows—it’s a full-sized, high-powered unit designed for serious use.

• Velocity: Rated around 400 feet per second

• Energy: Approximately 142 ft-lbs

• Features:

  • Detachable silent crank system for easier cocking

  • Picatinny rail for mounting optics or accessories

  • Full kit setup with multiple components included

This level of power puts it well into small-to-medium game hunting territory, making it more than just a recreational piece. Because of its size and power, testing it indoors isn’t really practical, so this one will likely get a detailed tabletop breakdown rather than a traditional shooting demo.

View fullsize

Umarex T4E TP50 Gen 2 (.50 Cal Tactical Pistol)

Next up is the Umarex T4E TP50 Gen 2, this time in the all-black tactical version rather than the more recognizable orange training model.

• Caliber: .50 caliber

• Velocity: Up to 465 FPS

• Ammo: Rubber balls (included in the box)

• System: CO2 powered with quick-pierce activation

This version stands out for a couple of reasons. First, the higher velocity suggests noticeably more energy compared to earlier or training-focused versions. Second, the all-black design gives it a much more realistic look, closer to a traditional firearm aesthetic.

Functionally, it uses a spring-fed internal magazine and a preloaded CO2 system, allowing you to keep it ready without gas leakage. When needed, a quick strike activates the CO2, making it immediately usable.

Based on typical .50 cal projectile weights and that velocity, this likely lands somewhere in the mid-to-high teens or possibly around 20 ft-lbs of energy, though exact numbers will be confirmed during testing.

View fullsize

E&L AKS-74N AEG Airsoft Rifle (Legends Series)

The final item in the box is a standout for realism: the E&L AKS-74N AEG airsoft rifle, branded under the “Legends / Legendary Perfection” line.

This is clearly built to replicate the real AK platform as closely as possible.

• Construction:

  • Real wood stock

  • Stamped steel receiver and metal components

  • Folding stock (magnetic lock)

• Operation:

  • AEG (Automatic Electric Gun)

  • Semi and full-auto firing modes

  • Adjustable rear sight (elevation)

• Extras:

  • Deans connector compatibility

  • Included specs sheet with velocity in m/s

The weight is immediately noticeable, estimated around 7–8 pounds, which adds to the realism. The combination of real wood furniture and steel construction gives it a very authentic feel compared to lighter, polymer-heavy Airsoft rifles.

The included magazine is polymer, but it should be compatible with standard AK-style AEG mags, meaning upgrades or swaps are likely straightforward.

Final Thoughts

This unboxing delivers a strong mix across three very different categories:

• High-power archery platform (AT400 crossbow)

• Compact CO2-powered .50 cal pistol (TP50 Gen 2)

• Full-metal, real wood AEG rifle (E&L AKS-74N)

Each item targets a different type of user, from tactical training and backyard use to collectors and realism-focused Airsoft enthusiasts.

As always, this is just the first look. Full tabletop reviews, comparisons, and field tests will break down real-world performance, usability, and value.

For availability and full write-ups, check:

• ReplicaAirguns.ca (Canada)

• ReplicaAirguns.us (USA)

• ReplicaAirguns.com (reviews and videos)

View fullsize

Today’s unboxing, we’ll call it the March 2026 Unboxing Preview!

I had no idea what was in this box, and honestly, I like it that way. It makes every delivery feel a bit like Christmas. A box shows up from the warehouse, I crack it open, and my job is to let you know what’s inside and what might be coming soon to the store. A lot of the time these are products we’ve never carried before. Not always, but usually there’s at least something new or unexpected in the mix.

As usual, getting into the box was its own little challenge. Good thing I had my “box cutter “ handy. Once I finally got through the packaging, it was clear right away this one had some interesting stuff inside.

What was in the box?

View fullsize

1) Annie Oakley Lil’ Sure Shot BB Rifle

First out of the box was something a little different: the Annie Oakley Lil’ Sure Shot.

This one is brought to you by Air Venturi / Western Justice, and it’s essentially a Red Ryder-style lever action BB rifle with some nice Western-themed touches. Right away, it stood out with the stained solid wood stock, wood forearm with engraving, and engraved Annie Oakley artwork.

Here are some of the listed specs and features:

• Ammo: .177 caliber / 4.5mm steel BBs

• Action: Lever cocking, spring piston

• Barrel: Smoothbore

• Overall Length: 36.25 inches

• Capacity: 550 BBs

• Claimed Velocity: Up to 350 FPS

• Weight: 3.3 pounds

• Max Shooting Distance: 212 yards

Once I opened it up, it definitely gave me that familiar Red Ryder / Marlin Cowboy vibe, but it feels like it may be just a bit bigger overall. Maybe a slightly longer stock, maybe just a bit more substantial in the hands. I’ll have to compare it side-by-side with a Red Ryder later to know for sure.

A few things I noticed right away:

• It has a metal lever

• Metal frame

• Metal barrel

• A plastic muzzle tip

• A rear sight that appears adjustable

• And surprisingly, a Weaver-style rail on top for mounting an optic

That top rail is actually a nice touch. You could absolutely throw a small scope on this if you wanted to, and why not? It makes for a fun little plinker, and the engraving gives it some real visual appeal too.

I’ve always had a soft spot for these little lever-action BB rifles. They’re just fun. They’re simple, classic, and a great way to introduce younger shooters to safe rifle handling. Rifles like this tend to be a bit easier for beginners since they’re not as quick to wave around as a pistol.

So yes, this one looks like it should be a lot of fun, and I’ll be doing both a Tabletop Review and a Field Test Shooting Review on it soon.

View fullsize

2) .68 Caliber Nylon Balls (100 Count)

Also in the box was a pack of 100-count .68 caliber nylon balls.

These feel noticeably heavier than the rounds I was using in my earlier T4E TC68 review. The previous ones were around the 2.8 to almost 3 gram range, and these new ones feel more like they’re getting up into the high 3 gram to 4 gram area.

That added weight could make them especially interesting to test in the TC68, since more projectile mass can sometimes translate into more energy on target, even if velocity comes down a bit.

So these should be fun to test out, and as it turns out, they may have arrived for a very good reason…

3) Steambow B08 / .68 Caliber Rubber Ball Crossbow Platform

This was the big surprise in the box, and definitely the highlight item.

If you watched my SHOT Show coverage, then you may remember this one from the Steambow booth. It’s a really cool product: basically a magazine-fed rubber ball shooting crossbow-style launcher in .68 caliber.

I had already gotten a chance to try it at SHOT Show, and Steambow was great about letting us check it out there. So it was pretty exciting to see one show up here for review.

Some of the box highlights:

• Detachable magazine

• 8-shot capacity

• .68 caliber projectiles

• Includes 25 foam balls

• Comes with a 35-pound limb

• AR-style adjustable buttstock

• Protective shooting glasses included

This product has a lot going on in the box. Once I opened it up, there were multiple components and accessories packed inside, including:

• Main body / receiver section

• Foregrip

• AR-style buttstock

• Upper receiver section with included magazine

• 35-pound limb

• Bow string and related accessories

• Lubricant / wax for the string

• Mounting hardware and tools

• Protective glasses

• 25 included foam balls

There’s definitely going to be some assembly involved before I can do a full review, so that will be part of the tabletop video.

The main unit itself feels solid and substantial. It has some good weight to it, and overall it looks like a very cool design. The included 35-pound limb should offer a decent balance between usability and performance. At SHOT Show we were only using a lighter 25-pound setup, which was very easy to draw, great for casual target practice, but obviously not the high-performance option.

One of the things I like about this platform is that it gives you that crossbow-style shooting experience while using reusable .68 caliber balls. That can make it easier and cheaper to shoot compared to bolt-style systems, where each arrow or bolt can get expensive fast, especially if you miss the target and damage one.

And since I now also have those heavier nylon .68 caliber rounds from the same box, I should be able to test both the included foam balls and the heavier options to see how they compare.

This one should make for a very interesting review.

Final Thoughts

So that was the March 2026 mystery box. We’ve got two very different products here:

• The Annie Oakley Lil’ Sure Shot, which looks like a fun, classic lever-action BB rifle in the Red Ryder tradition

• And the Steambow B08 / .68 Caliber Rubber Ball Crossbow Platform, which is something a little more modern, tactical, and definitely unique

Both of these are getting the full treatment, so expect Tabletop Review and Field Test Shooting Review videos for both products.

The Annie Oakley should be a blast to shoot, especially if it performs anything like the other Red Ryder-style guns I’ve reviewed over the years. And the Steambow system looks like it could be a really practical and fun way to enjoy crossbow-style shooting without the cost and fragility of traditional bolts.

I’ve still got a few earlier products to finish up as well, but I’ll be getting to these as quickly as I can.

Thanks for watching another Replica Airguns video. Don’t forget to subscribe, and check the links in the description for products available in our Canada and US stores.

For Canada, visit ReplicaAirguns.ca
For the US, visit ReplicaAirguns.us

And if you’re looking for other products including Airguns, BB guns, pellet guns, airsoft guns, blank guns, and accessories, be sure to check out both stores as well.

View fullsize

In this Field Test Shooting Review I’m taking a look at the Umarex T4E TC68 .68 caliber paintball / less-lethal marker to see how it performs in terms of velocity, accuracy, and overall shooting experience.

I have already done a Table Top Review covering the specifications, features, and overall purpose of the TC68, so make sure to check that video out if you want the full breakdown of the gun itself. This field test review is focused strictly on real-world performance.

For this test the TC68 has been de-restricted, meaning the adjustment screw has been modified slightly so it can reach its full potential. Even with this adjustment it should still remain legally compliant here in Canada, since the velocity will remain under the 500 fps threshold.

For ammunition I used .68 caliber nylon rounds:

• Black rounds: approximately 2.8 grams

• Yellow rounds: approximately 2.6 grams

The TC68 in this test is powered using dual 12-gram CO2 cartridges, rather than the larger 88-gram CO2 cylinder, which will affect both shot consistency and total shot count.

View fullsize

Velocity Testing

For the velocity portion of the test I fired several shots through my chronograph.

Chronograph readings were somewhat tricky to capture at first, but once everything started working correctly I was able to record several shots.

Example readings included:

• 476 fps

• 463 fps

• 453 fps

• 445 fps

The velocity dropped slightly during the test, which is expected when using dual 12-gram CO2 cartridges, as they cool down fairly quickly during rapid shooting.

The slightly heavier 2.8-gram black rounds were also used for some of the shots, which can contribute to minor changes in velocity compared to the lighter 2.6-gram rounds.

Even with that drop, performance was still strong and suggests the TC68 could likely reach high-400 fps velocities with a fresh CO2 setup or an 88-gram CO2 cylinder, which provides much greater gas capacity and improved consistency.

View fullsize

Accuracy Testing

For the accuracy portion of the test I set up a paper target down range and loaded roughly 20 rounds into the magazine.

The first test consisted of 10 shots in semi-automatic mode using the heavier black nylon rounds. A red-dot optic was installed on the TC68 for aiming, though it had not been sighted in or adjusted beforehand.

Results were quite respectable for a marker shooting heavy .68 caliber rounds.

• Overall grouping was approximately 4 inches

• Most shots landed within a 2.5–3 inch cluster

• One shot landed slightly low outside the main group

Considering the optic was not adjusted and this was essentially a right-out-of-the-box test, the accuracy was quite good.

Full-Auto Shooting Test

After the semi-auto accuracy test I attempted a full-auto burst test, but quickly discovered the CO2 had been depleted.

After installing fresh CO2 cartridges, the full-auto test was repeated with approximately 20 rounds loaded.

The TC68 does not have an extremely fast rate of fire, but it still delivers a solid stream of rounds when the trigger is held down.

View fullsize

During full-auto fire:

• The gun remained fairly controllable

• Rate of fire was moderate but effective

• CO2 cooling became noticeable during sustained bursts

A fresh target confirmed that the TC68 was still accurate enough for defensive-style shooting, keeping the majority of rounds within the main target area even during burst fire.

Power and Energy

Using approximately 2.8-gram nylon rounds traveling around 475 fps, the TC68 is producing significantly more energy than its factory-rated 16-joule output. Closer to 30 joules!

The modification performed simply allows the power adjustment screw to reach its full depth, allowing the marker to operate closer to its maximum potential.

While exact energy figures will depend on projectile weight and velocity, the TC68 in this configuration appears capable of producing considerably higher energy levels than stock, while still remaining under the 500 fps legal limit in Canada.

Shooting Impressions

Overall the Umarex T4E TC68 proved to be a solid and reliable platform during testing.

Some observations from the field test:

What I liked

• Strong velocity potential

• Good accuracy for a .68 caliber marker

• Full-auto capability for rapid follow-up shots

• Compatible with multiple CO2 power options

Things to consider

• Dual 12-gram CO2 cartridges cool down quickly

• Larger 88-gram CO2 cylinders will provide better consistency

• The gun includes multiple safety mechanisms that require familiarity

The TC68 includes three levels of safety, which helps prevent accidental discharge but does require some practice to become comfortable with the controls.

View fullsize

Final Thoughts

The Umarex T4E TC68 performed well in this field test.

Velocity was strong, accuracy was respectable for a .68 caliber marker, and the full-auto capability adds an interesting dimension to the platform.

With proper setup and a fresh CO2 source, the TC68 has the potential to deliver high-energy shots while still remaining within Canadian legal limits.

Overall it’s a very capable paintball / less-lethal marker and definitely an interesting option for those looking for a high-power .68 caliber platform.

• Buy the Umarex T4E TC 68 Less Lethal Paintball Rifle in Canada

• Buy Paintball Guns in the US

In this Table Top Review we’re taking a close look at the Sig Sauer P229 CO2 Blowback Pellet Pistol. This is the tabletop portion only, no shooting in this review as my Field Test Shooting Video will follow later on.

If you’re familiar with the Sig Sauer ASP P226 platform, the P229 version is the same general system in a more compact package, with one major upgrade: it’s optics-ready!

View fullsize

Specifications

• Manufacturer: SIG SAUER

• Power Source: 12g CO2

• Ammunition: .177 pellets (also supports steel BBs)

• Action: Semi-auto, blowback

• Trigger: DA/SA (double action / single action)

• Magazine: 16 rounds (twin 8-shot rotary clips, loaded on both ends)

• Barrel: Rifled inner barrel

• Sights: White dot sights

• Safety: Manual safety lever with de-cocker function

• Claimed Velocity: up to ~380 fps (real-world varies with temperature and cadence)

• Shots per CO2: roughly 50–60 (varies with temperature/cadence)

• Weight: 35.2 oz / 1.0 kg (2.2 lb)

• Overall Length: 7.7 in (P229)

• Optics: optics-ready slide / SIG AIR reflex-sight mounting provision

• Muzzle threads: M14x1 CCW

View fullsize

In the Box

• P229 CO2 blowback pellet pistol

• Manual

• Sight/plate parts for the SIG AIR reflex mounting setup (for red dot use)

P226 vs P229 - What’s Different?

These two share the same general operating system (CO2 blowback, DA/SA, rotary-mag that works with pellets/BBs), but the P229 version changes a few important things:

View fullsize

Key Differences

• Size: P229 is shorter (7.7 in) vs P226 (8.25 in).

• Weight: P229 is lighter (35.2 oz / 2.2 lb) vs P226 (~39.1 oz).

• Optics: P229 is optics-ready (SIG AIR reflex mounting provision); P226 platform is typically not.

• Muzzle threads: P229 uses M14x1 CCW (P226 commonly uses a different thread direction/size).

Bottom line: if you liked how the P226 handled and performed, the P229 should feel very familiar, just more compact, with the bonus of being set up for a dot.

Walk-Around & Handling

The P229 has that classic SIG profile and a very “real pistol” feel in the hand, helped by the mostly-metal build and full weight.

View fullsize

Notable features and controls:

• DA/SA trigger system: long/heavier first pull in double-action, then lighter single-action after the slide cycles.

• Safety + de-cocker lever: functions like the real-steel concept — you can decock the hammer and run it DA/SA.

• Accessory rail: for a light/laser (training-style setup).

• Optics-ready slide: set up to accept the SIG AIR reflex-style mounting system (sight sold separately).

CO2 System and Magazine Notes

One of the standout features on this platform is SIG’s cam-lever, tool-less CO2 loading system, designed to make cartridge swaps quick and easy.

The magazine is a 16-shot design using twin 8-shot rotary clips. Practical tip: make sure pellets are seated properly in the rotary clip so they don’t hang up during cycling.

View fullsize

Pros

• Mostly metal build with realistic weight and solid feel

• Compact P229 size (shorter than the P226)

• DA/SA trigger + functional safety/de-cocker system

• Blowback action for realism/training value

• Rifled inner barrel (pellet accuracy potential)

• Tool-less cam-lever CO2 loading system

• Optics-ready slide (big upgrade over older-style setups)

• Accessory rail for light/laser

Cons

• Fixed/non-adjustable sights

• CO2 performance is temperature + cadence sensitive (rapid fire cools the system and drops power)

• No last-round hold-open on this style of rotary-mag system

• Rotary clips require good pellet seating to avoid occasional feeding issues

View fullsize

Final Thoughts

The Sig Sauer P229 blowback pellet pistol is a very “SIG-like” training/plinking platform: realistic controls, DA/SA operation, snappy blowback, and a compact duty-pistol footprint. The biggest tabletop takeaway is the optics-ready slide, which makes this version feel more modern than older CO2 pellet pistol designs.

Field test shooting (chronograph + accuracy) will follow in the next video.

Available in our Canada Replica Airguns Store. Also check out:

• Buy the Sig Sauer P229 in Canada

• Buy the Sig Sauer P226 in the US

View fullsize

Type: .68 Cal Paintball / Training Marker Rifle /Less Lethal
Manufacturer: Umarex (T4E / Training for Engagement)
Model: T4E TC68
Made In: Taiwan
Materials: Polymer exterior with internal metal components (metal flash hider + various metal controls)
Weight: 2.5 kg (5.52 lb)
Overall Length: 84 cm (33")
Barrel: Approx. 31 cm (12") smoothbore (.68 cal)
Power Source: 2x12g CO2 (in-stock dual system), 88g CO2, or HPA (via included adapter)
Action: Semi-auto and full-auto
Ammo Type: .68 Cal paintballs, rubber balls (including heavier core types), powder/dust/chalk balls, glass balls, pepper balls (where legal), and First Strike–style shaped rounds (magazine-fed)
Ammo Capacity: 20-round spring-assisted magazine (plus hopper-fed option with included adapter)
Claimed Velocity Range: 240–480 fps (adjustable; depends heavily on ammo weight and air source)
Energy (Context): Marketed around 16J “out of the box,” with higher output possible via the built-in adjustment system (jurisdiction-dependent and often tamper-restricted)

View fullsize

Trigger Pull
The TC68 uses a semi-auto style trigger that feels closer to a single-action pull (it needs to work this way to support full-auto). The break is straightforward and predictable, and it suits the “training marker / utility” role well.

Accuracy

This table top review is focused on features, build, and usability. Accuracy testing and chronograph results are better handled in a field test once ammo weight is confirmed (rubber vs. paintball vs. hard plastic rounds will all change results). Initial “gut feel” shooting suggests the factory setting is already pushing hard for a training marker, with performance feeling consistent with the advertised 16J class.

Build Quality

The TC68 is largely polymer on the outside, but it doesn’t feel like a toy. The weight is substantial, controls feel solid, and the overall package is clearly built for training and repeated handling. You’re getting a robust platform designed to run multiple air sources and a wide range of .68 caliber projectiles without needing a bunch of aftermarket parts just to get started.

Realism / Ergonomics / Controls

Visually and ergonomically the TC68 leans into an AR-style layout:

• AR-style grip geometry (and AR-compatible grip fitment style)

• Full-length Picatinny top rail

• M-LOK on the handguard (sides and bottom) for lights, foregrips, etc.

• Ambidextrous selector (Safe / Semi / Full)

• Ambidextrous magazine release

It does not have real-steel operating controls like a charging handle or functional bolt/dust cover, this is a marker, not a firearm replica mechanism, but from a distance it reads like a modern sporting rifle pattern, which matters for training applications and general “presence.”

Safety systems are layered:

1. A “quick pierce / activation” setup (pressurizes the marker only when you choose)

2. A cross-bolt style safety that controls readiness to fire and can also depressurize when switched back (you’ll hear it vent)

3. Standard safe selector switch position

View fullsize

Air Source Flexibility (CO2 + HPA) and Included Hardware

This is one of the biggest selling points: it ships with a lot of the “bits and pieces” that usually cost extra.

You can run:

• Dual 12g CO2 (the configuration shown in the review)

• 88g CO2 (full-length stock configuration)

• HPA via included adapter (plus an alternate stock option that works well with compact tanks)

The included quick-pierce style setup is practical: you can stage the marker with CO2 installed without continuously bleeding gas, then activate it only when needed.

View fullsize

Feeding Options: Magazine-Fed or Hopper-Fed

Out of the box you get:

• A 20-round spring-assisted magazine designed to load easily (the spring can be held back during loading, then feeds when inserted)

• A hopper adapter system (hopper not included, but the adapter is), letting you run higher-capacity paintball-style feeding for volume use, especially relevant if you pair HPA + full auto

The magazine also supports First Strike–style shaped rounds (magazine-fed only), expanding the use-case options for training and scenario work.

Sights / Optics

No sights are included, no irons, no basics, nothing. That’s the odd omission on an otherwise “complete” kit. Plan on adding:

• a red dot (often easiest), and/or

• irons that sit higher, or a riser setup, depending on your preferred cheek weld and optic height.

View fullsize

Pros

• Multiple air source support (2x12g CO2, 88g CO2, or HPA via included adapters/stocks)

• Quick-pierce / staged-gas concept is practical for readiness without constant leaking

• Semi-auto and full-auto capability

• Adjustable power/velocity range to suit different training and ammo types

• Magazine-fed or hopper-fed flexibility (adapter included)

• Accepts First Strike–style shaped rounds (magazine)

• AR-style ergonomics and lots of accessory mounting (Picatinny + M-LOK)

• Strong “presence” and serious performance feel for a .68 platform

• In Canada especially, it fills a niche many users are actively looking for (training/marker/home safety versatility)

Cons

• Pricey in Canada (around the ~$600 CAD range at the time of the review)

• No sights included (you must budget for at least basic aiming equipment)

• Maximum performance potential may be restricted by factory tamper measures and local rules (and you should not assume higher settings are legal where you live)

View fullsize

Comments

If you want a .68 caliber platform that can legitimately be configured for multiple roles, paintball, training, scenario use, home safety use, the Umarex T4E TC68 stands out because it’s versatile right out of the box. The “complete kit” nature (CO2/HPA readiness + mag and hopper options) is rare at this price point.

The Umarex T4E TC68 is in probably one of the most powerful “Rubber Ball”Airguns you can get here in Canada right now with the ability to even turn it up a notch (at your own discretion). With Canadian legal gun owners losing their rights to own regulated Firearms more and more each day, being able to acquire something that is not regulated may be the best option for non-Firearms Licensed holders and Firearms Licensed holders.

Field test follow-up (chronograph + practical shooting) will matter a lot with this one, because performance varies dramatically with projectile type and weight. That’s where it will be most interesting to quantify real fps and estimated energy across a couple common round types.

• Buy the Umarex T4E TC 68 Less Lethal Paintball Rifle in Canada

• Buy Airguns in the US

It’s been a little while since I’ve done an unboxing, so we’ll call this the February 2026 Mystery Box Unboxing Video.

First up: SHOT Show is officially wrapped on my end, interviews, teaser, the whole run. There should be a playlist available so you can binge everything in one place. Now that the heavy editing grind is done, I’m getting back into regular reviews, unboxings, tabletop breakdowns, and full field tests.

Also: we’re back on YouTube and I’m uploading like crazy. I’m moving the library over from Vimeo one-by-one (lots of clicks, lots of time). We’ve got roughly 1,300 videos total, and I’m already around 500 videos in, so if you’re hunting for something specific, use playlists and search because new uploads can get buried fast. If you can, subscribe and share the channel with other Airgun enthusiasts so we can build momentum again.

What was in the box?

View fullsize

1) SIG P229 (.177 Pellet, blowback)

I initially called it a P226, but it’s the P229 (compact). This is a pellet version (not BB), with:

• 16-round rotary stick magazine (8 per side)

• Blowback, semi-auto

• Claimed 380 FPS

• 3.9" barrel, 7.7" overall length

• 2.2 lb, hefty all-metal feel (mag is plastic)

No slide lock-back due to the rotary setup, but it looks great in-hand. Tabletop and field test videos are coming, and I’ll run it on typical lead pellets to see real-world performance.

View fullsize

2) T4E TC68 (.68 cal, CO2/HPA capable)

This is the TC68 trainer that shoots .68 caliber rounds (rubber, powder, paint, pepper ball options depending on what you choose). Specs and highlights:

• Claimed 330 FPS and 16 joules

• 20-round magazine-fed setup

• Supports dual 12g CO2, 88g CO2, and HPA options

• Includes multiple configurations (stocks/adapters) plus a hopper-fed option

I’ll confirm operating modes, setup options, and performance in the upcoming tabletop and field tests.

• Buy the Sig Sauer P229 Pellet Pistol in Canada

• Buy the T4E TC 68 Paintball Rifle in Canada

View fullsize

We stopped by the SABRE booth and spoke with Ashley about their Home Defense Pepper Launcher, specifically a second-generation version that (per Ashley) isn’t released yet. With less-lethal options getting more attention in Canada, I wanted to see what’s new, what specs we’re looking at, and whether it’s something we might be able to bring in for reviews and potential store availability.

What’s new with the Gen 2 (as described in the interview)

• “Quick Pierce” magazine system: Ashley demonstrated a faster “pierce and go” style setup, hit the control and you’re ready to aim.

• Pressure indicator: After piercing, an indicator pops out; as CO2 is depleted it retracts, giving you a visual cue that pressure is running out.

• CO2 release button: A control to vent the CO2, then remove the magazine.

Core platform details (current production specs for the .68 launcher family)

These are the commonly listed specs for the current .68 caliber SABRE launcher:

• .68 caliber projectiles

• 7-projectile magazine capacity

• Fiber optic sights (front/rear adjustable)

• Stated velocity up to ~350 FPS

• Range: direct impact effectiveness noted around 60 ft (18 m), with projectiles described as breaking/dispersion capability out to 175 ft (53 m)

Ashley also noted SABRE’s projectiles have a heavier payload than some competitors (in her words) to help with “strength” and accuracy.

Magazines, CO2, and shot count (from the interview)

• CO2 goes into the magazine

• 7 projectiles per magazine

• Two magazines per CO2 (so 14 shots)

Canada angle (what matters for importing)

• Ashley noted the current model is around ~20 joules, and said a Canadian version would likely need to be lower(depending on classification/import requirements).

• SABRE’s own online store states they do not ship internationally, including Canada (so any Canada availability would likely be via distribution/import channels rather than direct-to-consumer shipment).

If we can make the Canada piece work, this looks like a strong candidate for a hands-on review, especially because it’s .68 caliber, 7-round, and built around visibility (fiber optics) and ease of use.

• Buy Replica Airguns in Canada

• Buy Replica Airguns in the US

View fullsize

We didn’t catch this one at the Steambow booth, we were out at the SHOT Show indoor range checking out Steambow again, Tyler walked us through their brand-new-for-2026 B08: a magazine-fed .68 caliber ball launcher/crossbow that’s just starting to hit availability.

• New B08 .68 cal “ball launcher” platform (2026): This is a .68 caliber system designed to run .68 spherical projectiles (paint, foam/nylon, and pepper/irritant-type balls were all discussed as compatible options, depending on local rules).

• 8-shot, removable, pre-loadable magazine: The B08 uses a spring-fed 8-round magazine that inserts at the front. Tyler’s demo made it clear you can pre-load multiple mags and keep shooting quickly.

• Simple, repeatable action (easy to learn fast): The manual of arms is very “repeat-and-go”: load the mag, cock it, shoot, then cycle and repeat. Steambow describes the system as their familiar AR-Series quick-tilt/quick-clamp style for fast reloading.

• Ships mild, but can be upgraded for more power: The one I tested was using a 35 lb limb, but it’s built to accept other AR-Series limbs (stronger options sold separately). Tyler specifically said swapping to a much heavier limb can turn it into a high-velocity setup (he referenced up to a 150 lb limb and around 300 fps in his talk).

• Projectile flexibility is the whole point: If you already have .68 cal paintballs or similar at home, that’s the target “ecosystem” this is built around (so long as they’re spherical).

• Important safety + legal reality check: Steambow is very explicit that once you move beyond the “low power + soft balls” envelope, the B08 can become very dangerous, they warn that harder/heavier projectiles (including steel balls) raise risks like severe injury/lethality and ricochets, and that irritant/pepper-type rounds may be legally restricted depending on country.

Tyler’s range demo made the main selling points obvious: magazine speed, easy operation, and a huge range of .68 ball options. If we can get it lined up for Canada, it looks like a very versatile multi use platform, especially for anyone who wants .68 cal fun adn then some, without relying on CO2 or HPA.

View fullsize

I caught up with Mark at the Umarex booth to check out a stack of new releases for 2026, ranging from backyard BB “fun guns,” to a major upgrade for the Thompson, plus a dual-fuel hunting/pest-control PCP concept and some serious less-lethal / training options.

• Storm Line BB Rifle (dual CO2, full auto): A traditional, “tamer-looking” BB rifle that’s anything but tame.

  • Capacity: 400-round main reservoir + 25-round ready magazine

  • Action: Full auto

  • Vibe: Affordable, high-volume backyard fun, while keeping the styling less “tactical,” which could help for markets like Canada.

• Ridge Tech Lever Action (CO2): Lever actions are hot, and this one leans modern while staying simple and budget-friendly.

  • Feed system: 8-round magazine + 120-round reservoir built into the mag

  • Use case: Tin-can plinking and family backyard sessions, “CO2 Red Ryder for adults” energy.

• Thompson M1A1 Drum Magazine Upgrade: The #1 request finally landed: a drum mag for the Thompson.

  • Capacity: 400 BBs

  • How it runs: Wind as needed to keep feeding similar to Airsoft High cap magazines

  • Best part: The drum magazine is planned to be sold separately and should work with the older stick-mag Thompson versions too, so existing owners can upgrade without buying the whole gun again.

• Outpost (25 cal) “Dual Fuel” PCP Concept: One of the most interesting items in the booth, a platform aimed at practical use over pure plinking.

  • Power source: Runs on a nitrogen cartridge or as a traditional PCP-style setup out of the box

  • Caliber: .25 only

  • Design notes: Side lever, folding stock for compact carry, onboard spare-mag storage (prototype shown)

  • Positioning: Built for small game / pest work and “preparedness” minded buyers

  • Canada angle: CO2 use (if supported) could drop velocity, but in this form it sounded like it may currently be on the “too fast for Canada” side, so detuned / CO2-focused variants were discussed as a possibility.

• S68 (68 cal, CO2, ~16J): Compact launcher format with real punch for its size.

  • Power: 12g CO2

  • Magazine: 6-shot standard, extended option mentioned

  • Ballistics talk: Roughly ~360–380 fps with a ~46-grain projectile (as recalled in the interview)

  • Ammo pairing: Steel-core “core defense” style rounds were emphasized for hard impact; pepper options depend heavily on local rules.

• HDX 68 “Shotgun Style” (68 cal): A higher-capacity, higher-energy format.

  • Capacity: 16 rounds

  • Energy: ~36 joules mentioned

  • Use case: Home / business defense in jurisdictions where these products and ammo types are legal.

• HDC 68 (M4/Rifle Style, CO2, adjustable): A configurable platform that can run mag-fed or hopper-fed.

  • Tuning: Adjustable velocity

  • Feeding: Magazine or hopper (round ammo works well; shaped rounds can be used depending on orientation)

  • CO2 options: 88g CO2 or adapters for 12g

  • Why not nitrogen (yet): Too much pressure without regulation, risk of damaging projectiles in the barrel.

• New Ruger-Branded 1911 (CO2 blowback): A dressed-up 1911 variant with extra detail.

  • Notable features: Flared magwell, two-tone finish, extended beavertail, competition-style touches

  • Appeal: A strong trainer option for 1911 fans, great feel, realistic handling, and that classic 1911 cycling character.

• Competition-Style CO2 Pistol (single-shot): A purpose-built target/competition format with modern mounting options.

  • Loading: Single-shot

  • Ergonomics: Competition grip + competition styling

  • Mounting: Built-in rail (no “upgrade it just to mount stuff” hassle)

  • Caliber shown: .177, with the obvious question of a future .22 variant.

Watch the Full Interview Video:

View fullsize

I just got back from SHOT Show 2026 in Las Vegas, and let me tell you, it was an action-packed trip! Over on our channels, we’ve just dropped a fast-paced highlight reel that captures the best moments of our week long stay.

The SHOT Show took place at the Venetian Convention Center, and you’ll see plenty of footage capturing the scale and energy of the event itself: busy show floors, massive booths, indoor and outdoor areas, and the overall atmosphere of one of the largest firearms and shooting-sports events in the world, with Airguns and related gear naturally woven throughout.

But it’s not just airguns, we’ve got slices of Vegas! You’ll catch us strolling Fremont Street, lounging poolside, and soaking up those iconic Vegas vibes between interviews. Whether you’re here for the Airguns or the atmosphere, this video’s got it all, music, cuts, the show floor, and a taste of Las Vegas. Check it out now and immerse yourself in the SHOT Show experience!

I was in Las Vegas last week for SHOT Show, filming content for Replica Airguns, but I wanted to post a quick update so you know what I was up to.

I went to SHOT Show to connect with people in the industry and record a bunch of interviews with vendors and companies, Airgun and aintball brands included (and more). I ended up filming about seven interviews, and now that I’m home I’ve got a lot of great footage to go through.

I was in Vegas with my buddy Steve (the guy behind the camera). Once the filming was wrapped, we spent some time enjoying the city after a busy week. We also did a few things outside of SHOT Show, because if you’re in Vegas, you might as well experience it.

In this video, we’re at the Montecristo Cigar Bar inside Caesars Palace, winding down with a nice port and a cigar.

Stay tuned,now that I’m back, I’ll start editing and posting those interviews. If you want to watch the SHOT Show interview series, head over to Replica Airguns or watch on our Vimeo and YouTube channels as I post them…

This one’s really growing on me because it’s not your standard AR platform. We review a lot of AR-style rifles (and there’s nothing wrong with ARs, they’re popular for a reason), but this one has a very different vibe. It’s based on the SA80 British service rifle design and comes in a compact bullpup layout that gives you a long inner barrel without needing a long overall rifle.

Today’s Table Top Review is the G&G L85A2 (A2 version) ETU Airsoft AEG Rifle — and yes, a full Shooting / Field Test Video will be coming shortly. I definitely want to get this one out and properly test it.

This model is available in our Canada store. At the time of recording this review, it wasn’t available in the US store, but I’ll add an equivalent/similar US option (or a list of comparable AEG rifles) in the post links.

View fullsize

Specifications:

• Manufacturer / Distributor: G&G (Made in Taiwan)

• Replica Of: SA80 / L85A2 (British 5.56×45 NATO service rifle family)

• Platform: Airsoft AEG (Electric)

• Ammunition: 6mm plastic airsoft BBs

• Operation: AEG with simulated blowback (reciprocating bolt for a slight “tap” feel)

• Fire Modes: Semi / Full Auto (and programmable for 3-round burst via MOSFET programming)

• ETU System: Programmable MOSFET + Electronic Trigger Unit (ETU)

• Motor: High-torque motor (rated around 25,000 RPM)

• Gearbox / Internals: Full metal gearbox, heat-treated metal gear set

• Bushings: 8mm oilless bushings for smoother gear rotation

• Hop-Up: Adjustable hop-up (access via dust cover)

• Trigger: AEG electric trigger (single-action-only style in practical terms)

• Safety: Cross-bolt safety

• Sights: Metal, fully adjustable front & rear

  • Front: elevation

  • Rear: windage

  • Rear peep sight includes two aperture sizes

• Weight: 6.0 lbs (2.7 kg)

• Overall Length: 27.5 in (70 cm)

• Inner Barrel Length: 16 in (40.6 cm)

• Magazine: 450-round high-cap AR-style AEG magazine (AR/M4-style AEG mags should fit)

• Velocity: Approx. 370–400 FPS with 0.20g BBs (varies by setup/conditions)

• Top Rail: Yes (carry handle/rear sight assembly sits here; optics possible with a riser)

• Flash Hider: Metal AR-style, black (no orange tip on this one)

• Sling Mounts: Multiple mounting points; front appears reversible L/R, rear has mounts on both sides

View fullsize

Build Quality & Materials:

This rifle has a really solid, substantial feel and is nicely balanced. There’s a lot of metal here.

Notable metal parts include (from what you can see and feel):

• Upper & lower receiver areas

• Carry handle / rear sight assembly

• Front & rear sights

• Magazine (metal high-cap)

• Trigger guard (metal for sure)

• Barrel, flash hider

• Sling mounts, pins/screws, switches and assorted hardware

View fullsize

Polymer / rubber components include:

• Handguards

• Pistol grip

• Cheek rest area (polymer)

• Butt plate (rubber)

Overall: it looks great, feels great, and doesn’t feel “toy-ish” at all.

In the Box:

• G&G L85A2 ETU AEG rifle

• 1× metal high-cap magazine

• Cleaning rod

• Product brochure / extra paperwork

• Transport muzzle cover / cap

• Manual access via QR scan (links to G&G’s online manual)

View fullsize

Walk Around Notes:

A few highlights from handling it up close:

• Bullpup layout: compact overall, but the barrel/inner barrel length is still substantial.

• Sighting system: the carry handle doubles as the rear sight platform with flip apertures.

• Optics compatibility: you can mount an optic on the top rail, but you’ll likely want a riser so your eye line sits naturally.

• Dust cover + hop-up access: you can open the cover and access hop-up adjustments the normal AEG way.

• Charging handle note: my rifle did not come with the charging handle piece. I checked my unboxing footage and it wasn’t on there and it wasn’t in the box. It’s not essential for function, but at this price point it’s something you’ll want to confirm is included on yours.

View fullsize

Battery Compartment:

The battery area is under the handguard, and here’s the main downside:

• If you’re running a larger battery, you’ll likely need to remove hardware (including the sling mount and a bolt) to open the lower handguard section.

• With smaller nunchuck-style batteries, you may be able to fit them in with less disassembly, but bigger packs will probably require tools.

So yes: it works, but it’s not a quick tool-free battery swap design.

Quick Function Check:

I did a quick dry-fire demo using a 9.6V battery, and honestly it felt a bit underpowered/odd (some partial taps and inconsistent behavior). That could be the battery itself (mine was not great), but I would suggest this rifle will really come alive with a proper 11.1V LiPo and hope to use this setup in the field test video.

I’ve seen demos where the rate of fire is very high using an 11.1V setup, so that’s what I’ll be testing with for the shooting video.

View fullsize

Pros:

• Lots of metal in the construction with a super solid weight, feel, and balance

• Unique bullpup British-style rifle (not just another AR build)

• Simulated blowback adds a bit of feedback vs. standard AEGs

• Works with AR/M4-style AEG magazines (easy to find replacements/midcaps/highcaps)

• Good optics flexibility on the top rail (carry handle sight system included, or add your own)

• Programmable fire mode: Full Auto or 3-round burst

• No orange tip (and if you prefer one for visibility, you can always add your own)

Cons:

• Limited accessory mounting options (mostly just the top rail; not a modern “add rails everywhere” setup)

• Battery access can require tools and disassembly, especially for larger batteries

• Priced on the higher side (around $600+ CAD)

• My sample was missing the charging handle part, check yours when it arrives

View fullsize

Final Thoughts:

This is a really nice AEG. It feels premium in the hands, the two-tone green looks great, and it’s a cool change from the sea of AR platforms, while still keeping things practical with AR-style AEG mag compatibility.

The simulated blowback isn’t going to replace the feel of a true gas blowback rifle, but it’s a nice touch, and paired with the ETU/MOSFET system and upgraded internals, it helps justify why this model sits in a higher price bracket.

Next up: the field test / shooting video, ideally with a proper 11.1V battery so we can see what this rifle really does when it’s running at its best.

Availability:

• Canada Store

• United States Store

And remember we carry air guns, BB guns, airsoft guns, pellet guns, blank guns, and accessories in both our Canada and US stores.

Thanks for watching and reading! Don’t forget to subscribe, and follow us on Facebook, Twitter, and Instagram. More videos coming soon…

View fullsize

In this Table Top Review, we’re taking a detailed look at the KJ Works KP-19S CO2 Blowback Airsoft Pistol. I’ve already reviewed the standard KP-19 in the past, and while the two pistols share a lot in common, there are some important differences between the KP-19 and the KP-19S that are worth covering.

I’m not entirely sure what the “S” officially stands for, possibly Sport—but interestingly, I’d actually argue that the non-S KP-19 is the more competition-oriented version, especially for IPSC-style Airsoft shooting. That said, the KP-19S still offers excellent performance, strong build quality, and a feature-rich design.

As always, this is a Table Top Review only. A full Shooting / Field Test Video will follow later.

This pistol is currently available in our Canada Replica Airguns store, and if a similar model is available in the US store, links will be provided in the video description.

View fullsize

Specifications:

• Manufacturer: KJ Works

• Made In: Taiwan

• Power Source: 12g CO2

• Ammunition: 6mm Airsoft BBs

• Action: Semi-auto, full blowback

• Trigger: Single-action, skeletonized, adjustable (1911-style)

• Magazine: Full-size dropout metal magazine, 25-round capacity

• Weight: 1.96 lbs (890 g)

• Overall Length: 9.84 inches (250 mm)

• Inner Barrel Length: 4.25 inches (108 mm)

• Claimed Velocity: 366+ FPS

• Hop-Up: Adjustable

• Rail: Under-barrel Picatinny rail

• Sights: Fiber-optic front and rear

• Safety: Ambidextrous

• Magazine Release: Reversible

• Threaded Barrel: Inner and outer threading

• Field Strippable: Yes (1911-style takedown)

The pistol includes a removable inner barrel extension, which may be required to reach the higher advertised FPS—something we’ll confirm in the upcoming field test.

View fullsize

In the Box:

• KP-19S CO2 Blowback Airsoft Pistol

• Full-size metal CO2 magazine

• Inner barrel extension

• Allen keys

• Small bag of Airsoft BBs

• Instruction manual (Usually!)

The pistol comes packaged in a basic cardboard box, but all essential accessories are included.

KP-19 vs KP-19S – What’s Different?

The KP-19S shares most of its core design with the standard KP-19:

• Same frame, grip, slide profile, trigger guard

• Same skeletonized trigger and hammer

• Same magazine compatibility

View fullsize

Key Differences

• KP-19 (Non-S):

  • Flared magwell

  • Compensator

  • Removable rear plate for mounting a red dot

  • More competition-oriented configuration

• KP-19S:

  • No flared magwell (cleaner, more streamlined look)

  • Fixed rear sight

  • Two-tone appearance

Performance between the two should be nearly identical, and if you’ve already watched the field test for the standard KP-19, expect similar results from the S version.

Walk-Around & Handling:

The KP-19S is a large pistol with a fairly wide grip. Shooters with smaller hands may find it bulky, but balance and weight distribution are excellent. At just under two pounds, it feels solid without being overly heavy.

Notable features include:

• Slide cutouts on the top and sides

• CNC-style gold/brass-colored fluted barrel visible through the slide

• Fiber-optic sights that are extremely easy to pick up

• Ambidextrous safety

• Reversible magazine release

• Dual threaded barrel system (inner and outer threads)

The full blowback action is strong, crisp, and satisfying, with excellent slide movement and reset.

View fullsize

Field Strip:

Field stripping follows a classic 1911 takedown:

1. Align the slide notch

2. Push out the takedown pin

3. Remove the slide assembly

Once opened, you gain easy access to:

• Inner barrel

• Recoil spring

• Hop-up adjustment wheel

Reassembly is quick and straightforward, making cleaning and maintenance easy.

View fullsize

Pros:

• High metal content with excellent weight and balance

• Strong, realistic full blowback action

• Excellent fit and finish typical of KJ Works pistols

• High-capacity 25-round metal magazine

• CO2 or gas compatibility (with appropriate magazines)

• Dual threaded barrel for accessories and extensions

• Bright fiber-optic sights (easy to acquire on any background)

• Short, light, adjustable 1911-style trigger

• Ambidextrous safety and reversible mag release

• Easy field stripping and hop-up access

Cons:

• Grip is wide and may not suit shooters with smaller hands

• Higher price point compared to similar KWC 1911 models

• Rear sight is not adjustable and does not accept a red-dot plate

  • Optics would need to be rail-mounted from underneath

View fullsize

Final Thoughts:

The KJ Works KP-19S is a high-quality, full-featured CO2 blowback Airsoft pistol with excellent build quality, strong recoil, and competition-inspired styling. While it lacks some of the modular competition features of the KP-19 non-s version, it offers a cleaner, streamlined look and the same reliable performance.

If you’re looking for a quality CO2 Airsoft pistol with a fantastic trigger, solid blowback, and premium construction, the KP-19S is a strong contender.

A full shooting and field test video will be coming soon.

Where to Buy:

🇨🇦 Canada:
https://www.replicaairguns.ca/kp-19s-hi-capa-gbb-airsoft-pistol

🇺🇸 United States:
https://www.replicaairguns.us
(A similar model may be linked if the KP-19S is not currently available)

View fullsize

More Reviews & Articles

Visit our blog for written reviews, photos, and additional info:
https://www.replicaairguns.com

Thanks for watching and reading.
Don’t forget to subscribe, and follow us on Facebook, Twitter, and Instagram.

Type: BB Rifle.
Manufacturer: Umarex.
Model: AER16.
Materials: Metal and plastic build.
Weight: 4.9 pounds (2.2 kilograms).
Length: 32.25-35.5 inches (82-90.2cm).
Propulsion: AEG (with Deans Connectors).
Battery: Comes with an 11.1 V 120 Mac Battery and USB Charger.
Action: Semi & Full Auto.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 55 rounds. (650 shots per battery charge Aprox.)
FPS: 430fps.
Rate of Fire: 450+ rounds per minute in full auto (depending on battery voltage).

View fullsize

Trigger Pull: The trigger on the Umarex AER16 AEG full-auto BB Carbine, like most AEGs, isn’t a purely mechanical trigger. It works as an electrical on/off switch, so it feels more like a light, short single-action pull. You’ll notice a small delay between pulling the trigger and the BB firing because the trigger starts a motor that first pulls the spring and piston back. Once the spring is fully drawn and released, it compresses air that propels the 4.5 mm steel BB. Using a higher-voltage battery reduces that delay, since the motor spins faster and returns the spring more quickly, which also raises the full-auto rate of fire.

View fullsize

Accuracy: I have not Field Test Reviewed the Umarex AER16 AEG full-auto BB Carbine or even tried it out yet so far, I hope to make my Field Test Shooting Video for it as soon as I can as I am very interested in how the AER16 performs compared to the Barra 400e which is a very similar AEG 4.5mm BB firing Airgun. If the AER16 shoots anything like the Barra 400e,I can expect it to shoot pretty close to 400 fps, with near 1 inch 10 round groupings in semi auto and slightly larger groups in full auto. You can checkout my Barra 400e Field test here.

View fullsize

Build Quality: The Umarex AER16 AEG full-auto BB Carbine is metal and Plastic in design with a plastic hand guard and receiver. That said, it does have a lot of metal parts including the barrel, buffer tube, magazine, trigger, charging handle, magazine release, dust cover, inner bolt shield, selector switch, sling mount and other bolts and pins! It feels very solid when holding it and the fit and finishes is really good. Since there is less metal all around then you find with the Barra 400e, this makes the AER16 a fair bit lighter coming around 5 pounds versus the Barra’s 7.5 pounds.

View fullsize

Realism: The Umarex AER16 AEG full-auto BB Carbine is based on the AR platform in terms of its overall design without any specific licensing other than Umarex branding. It does have a lot of working parts including the charging handle which opens the dust cover showing the simulated bolt. There is no Hop-up like you would find in a similar Airsoft Rifle but with BB’s this is not so much of a requirement. You will also find a working magazine release for the all metal magazine along with a working selector for semi and full auto shooting. The all metal buffer tube allows for an AR style rear adjustable stock which I would assume you can swap out for just about any AR buffer tube based rear stock.

View fullsize

Pros:

• No CO2 required so cost to shoot is less.

• Comes with high volt LiPo battery and charger

• Very consistent velocity as there is no cool down effect from CO2 cooling the gun (Just like an AEG Airsoft rifle).

• Have the option to shoot in semi or full auto modes.

• Lots of metal in construction (buffer tube, magazine, barrel, trigger, dust cover, charging handle, safety switch, magazine release sling mount.

• Lots of rail option for mounting accessories.

• Flip up removable sights with fully adjustable rear peep sight (single aperture).

• 6 position adjustable rear stock.

• Nice high capacity 55 round magazine, easy and fast to reload with speed loader.

• Lots of working parts including the charging handle, dust cover, magazine release, selector switch.

• Comes with safe storage bag for LiPo battery (no fear of burning your house down).

View fullsize

Cons:

• No blowback operation as with some other Full Auto BB Rifles like the Crosman AR Series.

• Receiver is plastic not metal.

• When battery is installed you can not use all the shorter positions of the adjustable rear stock.

View fullsize

Comments:

The Umarex AER16 AEG full-auto BB Carbine is a nice addition from Umarex to what Barra came out with a year or so ago with their 400e AEG Rifle. I like that the AER16 is a true AR Replica which is a very popular design and it is a lot lighter than the kind of heft 7.5 pound Barra 400e which may be a bit much for some smaller or lighter shooters to handle. The Umarex AER16 AEG full-auto BB Carbine also has the advantage that it comes with an included 1.11V 1200mAH LiPo batter and USB Charger so no further purchasing is required to shoot it other than some BB’s which most Air gunners will normally have on hand. One last point to make is that the AER16 is the less expensive option over the Gen 2 Barra 400e that come in both metal and polymer version.

• Buy the Umarex AER16 AEG full-auto BB Carbine in Canada

• Buy the Umarex AER16 AEG full-auto BB Carbine in the US