View fullsize

Today, we are putting the Specna Arms SA-F249 to the test. If you haven't seen one yet, be sure to check out the detailed tabletop review and the outdoor shooting video I've already posted. Today, however, is all about the hard numbers. We are bringing it into the indoor sea can to check the chronograph performance and see what kind of accuracy we can squeeze out of this absolute beast on paper. Let's get right to it.

Chronograph Velocity Test

To start things off, I loaded up some quality 0.25g airsoft BBs to run through the chrony. This setup currently has a standard voltage adaptor, for the LED lighting system though my usual one died on me, so I’m running an adjustable voltage adapter.

After a brief, accidental full-auto burst (remember, this is a support weapon designed to lay down cover!), we dialed it in for some attempted single shots (super short trigger pulls) to get our baseline velocity readings.

Chronograph Results (0.25g BBs):

• Shot 1: 363 fps

• Shot 2: 364 fps

• Shot 3: 365 fps

• Shot 4: 362 fps

• Shot 5: 363 fps

• Shot 6: 365 fps

The consistency here is phenomenal. We are sitting right in that 363 to 365 fps sweet spot. For an AEG out of the box, seeing variance of only a couple of feet per second between shots is a testament to the internal air seal and overall build quality.

Full-Auto Accuracy Test

With the velocity dialed in, it was time to set up a paper target downrange. Because this is a sport based automatic weapon, there's no semi-auto selector that I could locate, it's meant to be fired in full auto, and that’s exactly how we tested it.

Instead of the massive 1500-round box magazine it comes with, I opted to run a standard AR-15 style magazine for this indoor test. I locked it in, aimed just below the center of the target, and let the spring unwind until the mag the spring could not push anymore Airsoft BB’’s out, dumping roughly 50 to 75 rounds in one continuous burst.

View fullsize

The Results: Absolutely incredible. For a full-auto dump of that size, you would normally expect the BBs to spray across the paper. a little bit Instead, the Specna Arms SA-F249 punched a jagged, blown-out hole right through the target, resulting in a remarkably tight 2-inch grouping.

To pump that many rounds into such a condensed area on full auto is outstanding. It proves that this gun isn't just about suppressing fire; it provides highly accurate, concentrated fire downrange.

Final Thoughts

The Specna Arms SA-F249 is an incredibly impressive piece of kit. It delivers laser-like consistency on the chronograph and lays down surprisingly tight groupings in full auto. If you are looking for a support weapon that doesn't compromise on accuracy, this one needs to be on your radar.

Where to Buy: If you want to pick one of these up for yourself, or check out our other gear, head over to our stores:

• Buy the Specna Arms SA-F249 FN Machine Gun AEG Airsoft Rifle in Canada

• Buy Airsoft Rifles in the US

Thanks for tuning in and supporting the channel! Be sure to like, subscribe, and follow us for more reviews and shooting tests across YouTube, Rumble, Vimeo, Facebook, Twitter, and Instagram.

Take care, and we'll see you in the next one!

View fullsize

Today, we are checking out the second-generation Lil' Sure Shot Annie Oakley BB Rifle. This is essentially a Red Ryder-styled, spring-powered BB rifle.

If you are interested in seeing how this looks up close along with the specifications and details, make sure to check out the table-top video. Today is going to be all about shooting it.

Chronograph Velocity Test

To get started, I needed to warm up the chrony, which took a little bit of troubleshooting. I had an ongoing voltage issue with my chronograph lighting and had to use a voltage regulator set to almost exactly 7 volts to get it to work properly without a proper adapter.

Once the chrony was up and running, I put several rounds through the rifle to test the velocity. The velocity remained pretty consistent in the mid-300s, with shots recording at 341, 340, 333, 329, 334, and 332 fps. averaging out at 334.

View fullsize

Target Accuracy Performance

For the accuracy portion of the test, I set up a paper target 30 feet down range. Here is how the rifle performed:

• Grouping: After firing about 10 shots, the rifle got just over a two-inch grouping.

• Placement: The shots were well-centered from left to right, though it shot a little high even when aiming just under the bullseye. I noticed a few stray BBs came back, which happens if they hit metal instead of the cloth backboard, causing some high flyers. (This could of been me as the bulk of the shots all grouped really nicely)

• Sights & Adjustability: It can be a little tough on the eyes aiming black front and rear sights on a target when you need readers for most things, which may have contributed to some of those shots hitting slightly higher. You can adjust the elevation slightly by moving a little piece on the sight backward and forward to raise or lower it. The rifle also features a dovetail, allowing you to mount a nice optical sight or a red dot.

Trigger Pull & Feel

• Pull Weight: The trigger pull comes in at around 5 to 6 pounds.

• Action: It is fairly short with a pretty predictable break.

• Usability: It requires a little effort, but it is not a super hair trigger, making it perfect for youngsters who are just starting out with shooting.

Conclusion

Overall, the Annie Oakley Lil' Sure Shot delivers exactly what you want out of a classic, Red Ryder-styled spring-powered BB rifle: it's straightforward, reliable, and just plain fun to shoot. While you aren't going to get competition-level precision out of a smoothbore BB gun, holding a solid two-inch grouping at 30 feet and putting out very consistent mid-300s fps velocities proves that it is more than capable of handling your everyday plinking or indoor target practice.

What really makes this rifle shine is its accessibility. With a predictable 5 to 6-pound trigger pull that requires deliberate effort without being a super hair trigger, it is a fantastic option for youngsters who are just learning the fundamentals of shooting. Plus, the inclusion of a dovetail mount means there is room to grow with the shooter, you can easily slap a red dot on there if the standard black iron sights prove a bit too tough on the eyes against various target. If you are looking for an entry-level plinker that performs right where it should, this second-generation Lil' Sure Shot is a great place to start.

If you want to pick one of these up, links are in the description to buy in both Canada and the US.

• 🇨🇦 ReplicaAirguns.ca

• 🇺🇸 ReplicaAirguns.us

View fullsize

The Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol takes the already popular P320 platform and adds a more tactical, competition-inspired look with the Spectre Comp styling. In this Field Test Review, I focused mainly on real-world shooting performance including velocity, accuracy, trigger feel, blowback action, and overall handling. If you want all the detailed specifications and close-up overview footage, make sure to also check out my Table Top Review video for this model.

For this test I used standard Sig Sauer lead pellets, estimated around 7–8 grains rather than lightweight alloy pellets, giving a more realistic idea of what shooters can expect during normal use. Despite some chronograph frustrations during testing, the pistol delivered fairly consistent velocities once everything settled down. Average readings for my five shots through the Chronograph came in at 270 FPS, with highs reaching about 286 FPS during the initial shots and my slowest shot was 260 FPS. Considering the cooling effect common with CO2-powered airguns, the consistency was actually quite respectable for a blowback pellet pistol.

Accuracy testing was performed at 30 feet using a standard paper target. I fired a full 10-shot group and overall results were solid for a blowback pellet pistol with a higher-capacity belt-fed magazine system. Most shots grouped within roughly 2 inches, although the full spread opened up closer to 2.5–3 inches when including a couple lower shots likely caused by slight velocity variation from CO2 cooldown. Horizontal consistency was very good, with only a slight tendency to drift left. For a rapid-fire capable CO2 pistol with blowback, the accuracy was more than acceptable.

View fullsize

One thing worth mentioning is the trigger feelof the Sig Sauer Spectre Comp. Since the trigger system also advances the pellet belt during firing, there is naturally a bit more friction and a slightly longer pull compared to some rotary magazine designs. Even so, the trigger never felt excessively heavy or unpleasant. Rapid follow-up shots were still easy to manage, and the realistic blowback action adds a lot to the shooting experience.

The 20-round belt-fed magazine system is one of the biggest advantages of the Spectre Comp over many traditional rotary magazine pellet pistols. Instead of dealing with smaller 8-shot or flip-around style magazines, you get a much more enjoyable shooting session with fewer reload interruptions. Combined with the realistic weight, solid balance, and satisfying blowback recoil impulse, this pistol ends up being a very fun and practical option for target shooting and action-style plinking.

If you are looking for a realistic training-style pellet pistol that combines blowback action, higher magazine capacity, and solid handling characteristics, the Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol is definitely worth checking out. It offers a nice balance between realism and shooting fun while still delivering respectable accuracy and consistency for casual target shooting.

You can find more information about Airguns, BB guns, Pellet guns, Airsoft guns, Blank guns, and accessories over at Replica Airguns Canada and Replica Airguns US.

• Buy the Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol in Canada

• Buy Sig Sauer P320 Blowback Pellet Pistol in the US

View fullsize

The Umarex T4E TP50 Gen 2 continues to impress as one of the more powerful and practical compact less-lethal pistols currently available. In this field test review, I tested the all-black version using .50 caliber rubber-steel core rounds to see how it performs in terms of velocity, energy, and real-world accuracy. The black version is essentially the same as the orange-marked variant, just marketed a bit differently, with a more tactical appearance that may appeal to those looking for a serious training or home defense-style option.

For ammunition, I used the steel-core rubber balls rather than standard solid rubber rounds. These projectiles are slightly heavier and seem to carry noticeably more energy downrange without sacrificing too much velocity. In my opinion, they are probably some of the best ammunition choices for these types of pistols if maximum impact energy is your goal.

Velocity testing through the chronograph produced some very impressive numbers. The TP50 Gen 2 delivered readings of 319 FPS, 304 FPS, 310 FPS, 300 FPS, and 308 FPS, averaging just over 308 feet per second. With the steel-core rubber rounds weighing approximately 2.7 grams, the pistol produced roughly 12-13 Joules of muzzle energy using the Steel Core Rubber Balls but would have been closer the projected 15 Joules with all Rubber Balls, which is extremely respectable for a compact CO2-powered .50 caliber launcher. You can really hear and feel the power when firing this pistol, and it even generates noticeable recoil-like kick during shooting.

View fullsize

Accuracy testing was performed from 30 feet downrange using the six-round internal magazine. Paintball-style projectiles are naturally less precise than pellets or BBs due to their softer construction, surface ridges, and aerodynamic inconsistencies, but the Umarex T4E TP50 Gen 2 still delivered surprisingly solid grouping performance. After adjusting my aim slightly low due to the pistol shooting a little high initially, the remaining shots grouped well into the center portion of the target and produced clean, sharp holes through the paper target with about a 3 inch grouping.

In practical terms, this pistol clearly delivers enough impact energy to strongly discourage an attacker or aggressive threat. The steel-core rubber rounds hit extremely hard, especially considering the combination of high velocity and projectile mass. While heavy clothing would certainly absorb some impact, anyone wearing lighter clothing would absolutely feel these rounds. The all-black appearance also adds to the realistic tactical styling, which alone could act as a deterrent before a shot is ever fired.

Overall, the Umarex T4E TP50 Gen 2 proved to be accurate enough for close-range defensive-style use, delivered excellent power, and offered reliable operation throughout testing. The trigger feels good, the pistol handles nicely, and the performance with steel-core rubber ammunition was impressive across the board. For anyone looking for a compact CO2-powered less-lethal launcher with strong energy output and solid build quality, the TP50 Gen 2 is definitely worth considering.

You can find the Umarex T4E TP50 Gen 2 and other Airguns, BB guns, Airsoft guns, Pellet guns, Blank guns, and accessories at:

• Buy the Umarex T4E TP50 Gen 2 CO2 Paintball Pistol in Canada

• Buy Paintball Guns in the US

Despite a rocky start, my test with the Specna Arms SA-F249 machine gun did yield some eventual results. Initially, I set up multiple cameras (Three Sony Cameras, Insta360 X4, DJI Neo 2, Looki L1, Meta Ray-ban Gen 2) and planned a full-auto session aiming to empty the 1500-round magazine on a boat load of water filled cans. Unfortunately, the magazine’s feed malfunctioned, preventing the gun from firing as intended. Even so, I pivoted, swapping in an AR-15 magazine and still managed to get some satisfying shots on target. at the end of the video

It’s all part of the process: sometimes you get a lemon, but that doesn’t mean the day is totally lost. We did confirm that the gun itself works very well, and I hope to be revisiting this test with a new 1500 round magazine to give it a proper go. For now, at least we got a bit of action on those water-filled cans. Stay tuned for a follow-up, because I’m determined to show this LMG at its full potential!

• Buy the Specna Arms SA-F249 FN Machine Gun AEG Airsoft Rifle in Canada

• Buy Airsoft Rifles in the US

View fullsize

First Look & Overview

In this table top review, taking a detailed look at the Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol, a modern, competition-style airgun replica that closely mirrors its real steel counterpart. This model stands out with its aggressive styling, compensated muzzle, and optics-ready slide, making it one of the more premium-looking pellet pistols currently available.

This is a pellet-only airgun with blowback action, designed more for realism and handling than raw velocity. If already familiar with the Sig Sauer M17 pellet pistol, this one shares a lot of mechanical similarities, including the magazine system.

Specifications

• Caliber: .177 Pellet

• Action: Semi-auto, blowback

• Magazine: 20-round belt-fed rotary system

• Power Source: 12g CO2 (tool-free cam lever system)

• FPS: Claimed 340 FPS

• Weight: ~2.3 lbs

• Overall Length: 8.5 inches

• Barrel Length: 4.6 inches (rifled)

• Construction: Metal slide, polymer frame

• Sights: Fixed white dot front and rear

• Optics Ready: Yes (SIG Air RMR compatible)

• Rail: Picatinny accessory rail

• Safety: Ambidextrous manual safety

View fullsize

Build Quality & Design

The Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol delivers a solid mix of metal and polymer construction. The metal slide gives it realistic weight and feel, while the polymer frame helps keep things balanced. At around 2.3 pounds, it has a substantial presence in hand without feeling overly heavy.

The grip features enhanced texturing along with a flared magwell, adding to both aesthetics and usability. The slide includes light porting and is optics-ready, allowing for easy installation of a SIG Air RMR red dot.

One standout visual element is the compensated muzzle, which adds to the competition-style look. However, it also impacts field stripping, you’ll need to remove it to fully disassemble the slide.

View fullsize

Magazine & CO2 System

This pistol uses a 20-round belt-fed rotary magazine, which is housed within a drop-out mag body. Loading is straightforward:

• Remove the rotary belt insert

• Load pellets into each chamber

• Reinsert into the mag

CO2 is loaded using a tool-free cam lever system, which is fast and convenient compared to traditional screw-in designs.

Important note: the magazine needs to be firmly seated. A light insertion may not lock it properly, and due to the weight, it could fall out if not fully engaged.

Also worth noting, while the outer mag housing has some polymer components, the internal structure is mostly metal. Still, avoid dropping it on hard surfaces.

View fullsize

Handling & Controls

• Ambidextrous safety works from both sides, though visual indicators are only clearly marked on one side

• Trigger feels closer to double-action due to the rotary magazine indexing

• Slide cycles with blowback but does not lock back when empty

• Takedown lever is present, but full disassembly is limited by the compensator

The trigger has a solid feel and requires deliberate pull due to the indexing mechanism. This is normal for belt-fed pellet systems.

View fullsize

Sights & Optics

The pistol comes with fixed white dot sights, which are effective for quick target acquisition. However, they are not adjustable.

For those wanting more precision, the pistol supports SIG Air RMR optics, replacing the rear sight with an included plate.

Performance Expectations

The claimed velocity is 340 FPS, which is typical for blowback pellet pistols. Expect slightly lower speeds with lead pellets (recommended) compared to alloy pellets.

Blowback operation will also consume more CO2 than non-blowback models, trading efficiency for realism.

If looking for a performance reference, similar results can be expected to the Sig Sauer M17 pellet pistol due to shared internals.

View fullsize

Pros

• Excellent replica accuracy of the P320 Spectre Comp

• Realistic blowback with metal slide

• Good weight and balance (~2.3 lbs)

• 20-round high-capacity pellet magazine

• Tool-free CO2 cam lever system

• Rifled barrel optimized for pellet shooting

• Optics-ready (SIG Air RMR compatible)

• Flared magwell and enhanced grip texture

• Picatinny rail for accessories

• Magazine compatibility with M17

Cons

• Lower FPS compared to non-blowback pellet pistols

• Higher CO2 consumption due to blowback

• Fixed (non-adjustable) sights

• Pellet-only (no BB capability, though this protects rifling)

• Slide does not lock back when empty

• Field stripping requires compensator removal

View fullsize

Final Thoughts

The Sig Sauer P320 Spectre Comp pellet pistol is a strong option for anyone prioritizing realism, handling, and modern styling over raw power. It delivers a premium look with solid functionality, especially for training, backyard shooting, or collectors wanting a high-end replica.

While not the most powerful pellet pistol available, it excels in design, usability, and realism, especially if already a fan of the P320 platform.

For those in Canada, availability may already be live, with US availability likely to follow.

• Buy the Sig Sauer P320 Spectre Comp CO2 Blowback Pellet Pistol in Canada

• Buy Sig Sauer Airguns in the US

View fullsize

In this review, we are looking at two crossbows that honestly shouldn’t really be compared, but that’s exactly why this comparison is interesting. On one end, we have the Steambow M10, a compact, magazine-fed, fast-shooting crossbow built for fun, training, and high repetition shooting. On the other, the CenterPoint AT400, a full-size, high-powered compound crossbow designed for serious hunting applications.

Aside from both launching bolts/arrows, these two platforms sit at completely opposite ends of the spectrum. The goal here is not to declare a winner, but to help you decide which one actually fits your use case, or if you might want both.

Key Differences Overview:

Steambow M10

The Steambow M10 is a compact repeating crossbow designed more for fun, training, and high-volume shooting. It uses a magazine-fed system that can hold 10 bolts, allowing for very fast follow-up shots. Depending on the limb setup, it can reach speeds of up to around 200 FPS and produce approximately 10 to 15 foot-pounds of energy. Its lighter draw weight options and easy cocking system make it beginner-friendly and much less physically demanding to use. Overall, the M10 is best suited for target shooting, casual use, and potentially small game with the right setup.

CenterPoint AT400

The CenterPoint AT400 is a full-size compound hunting crossbow built for serious power and hunting use. Unlike the M10, it is a single-shot platform that focuses on accuracy, penetration, and range rather than fast repeat shooting. It sends arrows downrange at about 400 FPS and delivers close to 150 foot-pounds of energy, putting it in an entirely different class. With its roughly 200-pound draw weight, it requires much more effort to cock and reload, usually with a rope or crank system. This makes it better suited for medium to large game hunting, where power and shot placement matter far more than speed.

Side-by-Side Summary

If you want something lightweight, compact, fast, and easy to shoot often, the Steambow M10 is the better fit. If your main goal is hunting and you need maximum power, longer range, and serious downrange performance, then the CenterPoint AT400 is clearly the more appropriate choice. Even though both are crossbows, they are built for very different types of users and very different shooting experiences.

Power & Performance

The biggest separation between these two comes down to raw power.

• The Steambow M10 delivers up to about 10–15 foot-pounds of energy, depending on limb configuration and bolt weight. It’s comparable to higher-end airguns or paintball-level power.

• The CenterPoint AT400, by contrast, produces close to 150 foot-pounds of energy and launches arrows at around 400 FPS.

That’s not a small difference, it’s an entirely different category.

Real-world comparison:

• M10 = backyard shooting, small game potential

• AT400 = deer, and potentially even elk with proper shot placement

This is essentially the difference between a BB gun vs a hunting rifle in terms of role and impact.

View fullsize

Shooting Experience:

Steambow M10

• Magazine-fed (10 bolts)

• Extremely fast follow-up shots

• Break-action style cocking (very quick)

• Great for drills, repetition, and skill building

• Minimal effort required

You can realistically fire 10 shots in about 10 seconds, making it a very engaging and fun platform.

CenterPoint AT400

• Single-shot system

• Requires rope cocking or crank system

• Significant physical effort (200 lb draw)

• Slow reload (often 30–60+ seconds)

This is a deliberate shooting experience, not something designed for volume or speed.

Use Case Breakdown:

Steambow M10 – Best For…

• Backyard shooting (with proper backstop)

• Target practice

• Tactical-style drills

• High repetition training

• Casual and frequent use

• Lower-cost shooting (especially with rubber ball version)

View fullsize

You can even use:

• Rubber balls (low cost, reusable)

• Lightweight bolts

• Indoor-friendly setups (with proper safety)

CenterPoint AT400 – Best For…

• Hunting (deer and potentially larger game)

• Long-range accuracy

• Maximum penetration and power

• Purpose-driven shooting

This is not a casual-use product, you typically bring it out when it matters.

Ease of Use & Physical Demand:

Steambow M10

• Very easy to cock (even at lower draw weights)

• Beginner-friendly

• Lightweight (~compact platform)

• Minimal fatigue

View fullsize

CenterPoint AT400

• High effort required

• Needs cocking tools (rope or crank)

• Physically demanding

• Slower workflow between shots

Key takeaway:
Anyone can pick up and use the M10 easily. The AT400 requires more commitment, strength, and practice.

Size & Portability

Steambow M10

• Compact and lightweight

• Can be partially disassembled easily

• Backpack-friendly

• Ideal for mobile use

CenterPoint AT40

• Large, fixed structure

• Not easily transportable without a case

• Designed for field carry, not casual portability

Ammo & Cost of Ownership:

View fullsize

Steambow M10

• Bolts are smaller and cheaper

• Rubber ball version = extremely low cost

• Less wear and tear overall

• High reusability

CenterPoint AT40

• Arrows are larger and more expensive

• More prone to damage/loss at high speeds

• Requires maintenance and replacement over time

Value Consideration:

Interestingly, both fall into a similar price range (~$400–$500), but value depends on usage frequency:

• M10 → Likely used often → Higher practical value

• AT400 → Used less frequently unless hunting regularly

If something sits unused, its value drops regardless of price.

View fullsize

Who Should Buy Each?

Choose the Steambow M10 if you…

• Want fun, fast shooting

• Plan to shoot frequently

• Prefer low effort and ease of use

• Don’t need high power

• Enjoy tactical or training-style shooting

Choose the CenterPoint AT400 if you…

• Are hunting (especially deer or larger game)

• Need high power and penetration

• Value accuracy and range

• Don’t mind slower reload times

• Are comfortable with physical effort

View fullsize

Final Thoughts

These two crossbows are not competitors—they are tools for completely different jobs.

• The Steambow M10 is about frequency, fun, and versatility

• The CenterPoint AT400 is about power, precision, and purpose

If anything, this comparison highlights that you may not need to choose one over the other, you might actually benefit from having both ends of the spectrum covered.

If neither fits perfectly, then the real answer may be to look for something in the middle.

Where to Buy

Both of these crossbows (or similar models) are typically available through:

• Buy Steambow M10 in Canada

• Buy CenterPoint AT400 In Canada

• Buy in the US

View fullsize

In this table top review, we’re taking a look at the Umarex T4E TP50 Gen 2 CO2 Paintball Pistol, part of Umarex’s T4E (Training for Engagement) lineup. This version is marketed more as a tactical training pistol, while its nearly identical counterpart, the HDP50, is positioned toward home defense.

At first glance, the TP50 and HDP50 look almost identical. The main visual difference is that the TP50 comes in an all-black finish, while the HDP50 features an orange slide. Beyond that, the functionality, performance, and specs are essentially the same.

Key Features and Specifications

• Manufacturer: Umarex

• Model: T4E TP50 Gen 2

• Caliber: .50 caliber

• Power Source: 12g CO2 (quick piercing system)

• Action: Semi-auto, double action trigger

• Magazine Capacity: 6 rounds (internal inline magazine)

• Velocity: Rated up to 465 FPS

• Energy: Claimed 11 joules (can be higher depending on ammo)

• Barrel Length: ~4 inches

• Overall Length: ~8 inches

• Weight: ~1.5 lbs (0.7 kg)

• Construction: Polymer frame and slide with metal internals and barrel

• Safety: Integrated trigger safety

• Rail: Under-barrel Picatinny rail

• Sights: Fiber optic front and rear

View fullsize

Overview and First Impressions

The TP50 Gen 2 is a compact, .50 caliber paintball-style pistol designed for training, recreational shooting, and less-lethal applications. It has a solid feel in the hand, not too heavy, not too light, and resembles a full-size handgun profile, similar in size to a large-frame pistol.

Despite its polymer exterior, the internal components that matter, especially around the CO2 system—are metal, giving it durability where needed.

CO2 System (Quick Piercing Feature)

One of the standout features is the quick piercing CO2 system:

• Insert the CO2 cartridge (butt-first)

• Tighten the cap until snug

• When ready to use, give the bottom a firm “whack”

• A pin pops out on the back where you can see it to indicate the system is pressurized

This allows you to keep the pistol loaded but not activated, which is useful for storage or readiness situations.

View fullsize

Ammo Compatibility

The Umarex T4E TP50 Gen 2 CO2 Paintball Pistol supports a wide range of .50 caliber ammunition, including:

• Rubber balls

• Powder balls

• Paintballs

• Steel/rubber hybrid balls

• Pepper balls (limited availability in Canada)

Performance varies significantly depending on the weight of the projectile:

• Lighter rubber balls: ~450 FPS / ~13–15 joules

• Heavier projectiles: lower energy (down to ~7–11 joules)

View fullsize

What’s Included

• TP50 Gen 2 pistol

• Two tubes of 10 rounds each (powder + rubber balls)

• Barrel cleaning squeegee

• Instruction manual

• Cardboard packaging (blue “tactical pistol” branding)

View fullsize

Walkaround Highlights

• Fiber optic sights make target acquisition easy in various lighting conditions

• Textured grip and slide for solid handling

• Metal trigger with integrated safety

• Wide open barrel design

• Picatinny rail for adding lights or lasers

• Clear “Strike” marking for CO2 activation point

Overall, it’s a clean, functional design with a tactical look, especially in the all-black version.

View fullsize

Pros

• Compact size compared to other .50 cal pistols

• Wide variety of compatible ammo types

• Quick piercing CO2 system (very practical)

• Good power for its size (~11–15 joules range)

• Fiber optic sights improve usability

• Picatinny rail for accessories

• Realistic all-black tactical appearance

Cons

• Only 6-round capacity before reload

• Limited shots per CO2 (~3–4 reloads)

• Internal magazine (no quick mag swaps)

• Pepper ball ammo difficult to source in Canada

• Efficiency trades off for higher power

TP50 vs HDP50 (Quick Comparison)

• TP50: All black, marketed as tactical training

• HDP50: Orange slide, marketed for home defense

• Performance: Essentially identical

View fullsize

This difference is largely cosmetic and marketing-driven, so choosing between them comes down to preference and intended use.

Final Thoughts

The Umarex T4E TP50 Gen 2 CO2 Paintball Pistol is a solid, compact .50 caliber CO2 pistol that delivers respectable power in a manageable platform. It’s not designed for high-capacity shooting or efficiency, but rather for impact, simplicity, and versatility in ammo choice.

If you’re looking for a less-lethal option or a training pistol with realistic handling and solid performance, the TP50 fits that role well, especially if you prefer the more discreet all-black tactical look.

Where to Buy

• 🇨🇦 Buy the T4E TP50 in Canada: ReplicaAirguns.ca

• 🇨🇦 Buy the T4E HDP50 in Canada: ReplicaAirguns.ca

View fullsize

In this table top review, we’re taking a close look at the Air Venturi Annie Oakley Lil’ Sure Shot Spring BB Rifle. While this is technically a “table top” review, lever-action rifles like this are always a bit easier to show off in-hand due to their length and proportions.

This model fits into a long lineage of classic lever-action BB rifles, alongside well-known options like the Daisy Red Ryder and the Marlin variants from Crosman and Umarex. These rifles all share a similar concept, simple, spring-powered, lever-action BB guns designed for training, plinking, and beginner shooters, but each brings its own subtle differences in materials, styling, and features.

Key Specifications

• Model: Air Venturi Annie Oakley Lil’ Sure Shot

• Type: Lever Action Spring Piston BB Rifle

• Caliber: 4.5mm Steel BB

• Power Source: Spring (No CO2 Required)

• Velocity: Up to 350 FPS

• Magazine Capacity: 550 Round Internal Reservoir (Gravity Fed)

• Action: Lever Action

• Safety: Cross Bolt Safety

• Barrel: Smoothbore

• Stock: Stained Solid Wood

• Construction: Primarily Metal with Some Plastic Components

• Weight: Approx. 3.3 lbs

• Overall Length: ~36.25 inches

• Optics Rail: Removable Weaver/Picatinny Style Mount

First Impressions & Build Quality

The Annie Oakley Lil’ Sure Shot stands out with its classic Western styling, enhanced by engraved Annie Oakley branding on the wood stock. It’s a step above many entry-level BB rifles thanks to its real wood stock and metal lever, giving it a more authentic and durable feel compared to fully plastic alternatives.

Most of the rifle is metal and wood, though there are a few plastic components:

• Trigger

• Front sight (on the newer version)

• Adjustable portion of the rear sight

• Removable scope rail

Overall, it feels solid in the hands, lightweight, and well-balanced, especially for younger shooters or anyone new to lever-action rifles.

View fullsize

How It Works

This is a spring-piston, lever-action BB rifle, meaning:

• No CO2 or gas is required

• Each shot is powered by cocking the lever

• BBs are stored in a large internal reservoir

• You must tilt the rifle upward to gravity-feed BBs into position

With a 550-round capacity, you can shoot for quite a while before needing to reload, your arm will likely get tired before you run out of ammo.

Handling & Usability

This rifle is clearly designed with accessibility in mind:

• Lightweight (3.3 lbs) makes it easy to handle

• Shorter length and pull fits smaller shooters well

• Moderate cocking effort is manageable for beginners

• Lever action slows firing rate, adding a safety advantage for new users

Rifles like this are excellent for training because:

• They are easier to aim than pistols

• They encourage controlled shooting

• They are not overly powerful

Even for experienced shooters, these are simply fun and inexpensive for backyard plinking.

Sights & Optics

Out of the box, the Air Venturi Annie Oakley Lil’ Sure Shot Spring BB Rifle includes:

• Fixed front sight (plastic on newer version)

• Adjustable rear sight (elevation only)

One notable feature is the removable Weaver-style rail, allowing you to:

• Mount a red dot or scope

• Or remove it for a more traditional look

Keep in mind the rail is plastic, so care should be taken when mounting optics.

View fullsize

Comparison to Similar BB Rifles

This rifle sits in the same category as:

• Daisy Red Ryder – The original classic

• Umarex Marlin Lever Action – Slightly more adult-oriented design

• Crosman Marlin (older models) – Direct Red Ryder competitor

All of these:

• Use lever-action spring systems

• Have internal BB reservoirs

• Shoot in the ~300–350 FPS range

The Annie Oakley version distinguishes itself with:

• Better visual styling

• Wood and metal construction

• Optional optics mounting

New vs Older Annie Oakley Version (Key Differences)

If you come across different versions, here are the main distinctions:

Newer Version:

• Longer barrel

• Plastic front sight

• Larger loading port (easier to load)

• Metal Lever

• Brighter, more polished wood finish

View fullsize

Older Version:

• Shorter barrel

• Metal front loading system (rotating port)

• Metal front sight (more durable)

• Plastic Lever

• Slightly darker, more matte wood

Both should perform similarly, but the newer version is a bit more refined with that quality all metal lever.

Pros

• Lightweight and easy to handle

• Real wood stock and metal lever construction

• Large 550-round capacity

• No CO2 required (low maintenance and inexpensive to shoot)

• Removable optics rail for flexibility

• Classic Western styling with Annie Oakley branding

• Great for beginners and younger shooters

Cons

• Plastic front sight (new version)

• Lower power compared to CO2 rifles

• Rear sight only adjustable for elevation

• Slightly higher price than some entry-level similar BB rifles

• Less realistic than shell-ejecting lever-action models

Final Thoughts

The Air Venturi Annie Oakley Lil’ Sure Shot is a well-built, visually appealing lever-action BB rifle that blends classic styling with modern usability.

It’s ideal for:

• Beginners and younger shooters

• Backyard plinking

• Anyone wanting a simple, reliable and fun BB rifle

While it doesn’t aim for full realism like higher-end shell-ejecting models, it delivers where it matters, ease of use, affordability, durability, and fun factor.

Available at:

• 🇨🇦 ReplicaAirguns.ca

• 🇺🇸 ReplicaAirguns.us

Also check out ReplicaAirguns.com for additional articles, photos, and video reviews.

Replica Airguns takes a step back in time to share how everything began, long before the channel, website, and stores grew into what they are today. The journey started around 2006, just a year after YouTube first launched. At the time, online video was still in its infancy, with low-resolution clips, shaky footage, and minimal production quality being the norm.

Mike created the very first video simply for fun. It featured a modified Umarex Walther PPK BB gun that Mike had altered for full-auto shooting. Edited in iMovie on a Mac and uploaded in low resolution (under 640×480), the video wasn’t intended to be anything more than a casual experiment. However, after sitting online for a few months, it unexpectedly reached around 100,000 views, an impressive number for that era, when far fewer creators were uploading content and viral videos were rare.

That early success revealed something important: there was real interest in Airguns and BB gun content. From there, Mike purchased more Airguns (to his wife’s disapproval), more videos were created, and the foundation for a focused channel began to take shape. A few years later, the project became more serious, evolving into a dedicated platform and eventually transitioning into the Replica Airguns brand you see today!

Over time, the brand expanded into multiple websites, ReplicaAirguns.com, ReplicaAirguns.ca, and ReplicaAirguns.us, along with a large video library. Although the channel faced setbacks, including being removed from YouTube at one point, the content continued to live on through platforms like Vimeo and Rumble. Now, with nearly all videos being restored back to YouTube, the library is close to fully rebuilt.

The original video that started it all was thought to be lost for years, buried on old storage drives. Recently rediscovered, it has been enhanced using modern AI tools to improve clarity while still preserving its original look and feel. Despite its dated quality, it represents the true starting point of the Replica Airguns journey.

For viewers interested in Airguns, including BB guns, Airsoft, Pellet guns, and more, the channel and websites continue to offer extensive content and product availability across both Canadian and U.S. online stores.

View fullsize

In this Video I perform the field test shooting review for the SIG Sauer P229 pellet pistol. If you’re interested in the full specifications, features, and a closer look at the pistol itself, make sure to check out my tabletop review where I go over all the details on this gun.

For today’s test I’m going to be shooting SIG Sauer lead pellets, roughly 7–8 grains. Because these are standard lead pellets and not lightweight alloy pellets, they’re not going to produce the highest velocity numbers this pistol can achieve. With lighter alloy pellets you will definitely see faster readings.

You could also shoot steel BBs through this gun, but BBs sometimes don’t seal quite as tightly in the barrel as pellets do. When that happens, some of the CO₂ can slip around the BB as it travels down the barrel which can actually reduce velocity slightly. BBs also generally don’t carry energy to the target as well as pellets, so pellets are usually the better option for accuracy and performance.

With these pellets, I’m expecting roughly around the 300 FPS range, so let’s see how it actually performs.

View fullsize

Velocity Test

For the velocity portion I’m going to put five shots through the chronograph to see what kind of numbers we get.

Chronograph Results:

Shot Velocities: 320 FPS - 296 FPS - 303 FPS - 286 FPS - 277 FPS (Average of 296 FPS)

As you can see, the readings are right about where expected, generally around the 300 FPS mark, with a slight drop toward the last shot. That’s fairly typical for CO₂ powered blowback pistols, since some of the gas is being used to cycle the slide.

View fullsize

Accuracy Test:

For the accuracy portion I’ve set up my paper targets at 30 feet downrange.

The SIG Sauer P229 pellet pistol uses a dual rotary 8-round magazine, so instead of the usual 10 shots I normally use in these tests, I’m going to fire eight shots to keep things simple and consistent.

One thing I like about this pistol is the trigger operation. When you start the trigger pull, the first stage rotates the rotary magazine. This part of the pull is very light and smooth, so there’s very little double-action feel. Once that’s done, you reach the single-action hammer release, which is nice and predictable.

To keep the trigger as light as possible I’m going to pre-cock the hammer, which eliminates most of that initial rotation effort and gives you a much lighter break.

View fullsize

Accuracy Results:

After eight shots at 30 feet, the group measured approximately 1.5 inches.

That’s actually pretty good accuracy for a blowback pellet pistol.

The pistol was shooting slightly low out of the box, roughly about two inches low and just a little to the left at this distance. My aim point was just underneath the bullseye so I could see the target above the sights.

The sights on this pistol are fixed, so you can’t adjust them directly. The easiest solution is simply to aim slightly higher and a bit to the right if you want to hit the bullseye consistently at this range.

View fullsize

Sight Upgrade Options:

If you want more precise adjustment, you do have a couple of options:

• Install a slide-mounted red dot using the removable optics plate

• Add a laser to the accessory rail under the barrel

Either of those options would allow you to dial in your point of aim exactly where you want it, which is a nice upgrade path for this pistol.

View fullsize

Shooting Impression

The trigger feels really good, and the blowback action is solid and snappy, though not overly fast.

The slide actually has a bit of that heavier, slightly slower 1911-style blowback feel, which I personally like. Some blowback pistols cycle extremely quickly and can feel a bit artificial, but this one feels more substantial because of the heavier slide weight.

The pistol itself also has good weight and balance, coming in a bit over two pounds, giving it a very realistic feel in the hand.

Overall, it’s a solid, well-built pellet pistol, and like many of the SIG Sauer Airgun products, it feels like a lot of attention went into the design.

SIG doesn’t actually manufacture these Airguns themselves, they design them and partner with manufacturers to produce them, but the quality across their pellet pistols and rifles has generally been very good.

View fullsize

Final Thoughts

The SIG Sauer P229 CO₂ blowback pellet pistol delivers:

• Around 300 FPS velocity with lead pellets

• Realistic blowback action

• Good weight and handling

• Approximately 1.5 inch accuracy at 30 feet

• Multiple options for optic or laser upgrades

Overall, it’s a very enjoyable pistol to shoot and a solid option if you’re looking for a realistic blowback pellet pistol.

Don’t forget to subscribe, and check us out on Facebook, Twitter, and Instagram.

If you’re interested in buying Airguns, BB guns, Airsoft guns, Pellet guns, Blank guns, and Accessories, be sure to visit our online Canada and US Stores.

Available in our Canada Replica Airguns Store. Also check out:

• Buy the Sig Sauer P229 in Canada

• Buy the Sig Sauer P226 in the US

View fullsize

In this Field Test Shooting Review I’m taking a look at the Umarex T4E TC68 .68 caliber paintball / less-lethal marker to see how it performs in terms of velocity, accuracy, and overall shooting experience.

I have already done a Table Top Review covering the specifications, features, and overall purpose of the TC68, so make sure to check that video out if you want the full breakdown of the gun itself. This field test review is focused strictly on real-world performance.

For this test the TC68 has been de-restricted, meaning the adjustment screw has been modified slightly so it can reach its full potential. Even with this adjustment it should still remain legally compliant here in Canada, since the velocity will remain under the 500 fps threshold.

For ammunition I used .68 caliber nylon rounds:

• Black rounds: approximately 2.8 grams

• Yellow rounds: approximately 2.6 grams

The TC68 in this test is powered using dual 12-gram CO2 cartridges, rather than the larger 88-gram CO2 cylinder, which will affect both shot consistency and total shot count.

View fullsize

Velocity Testing

For the velocity portion of the test I fired several shots through my chronograph.

Chronograph readings were somewhat tricky to capture at first, but once everything started working correctly I was able to record several shots.

Example readings included:

• 476 fps

• 463 fps

• 453 fps

• 445 fps

The velocity dropped slightly during the test, which is expected when using dual 12-gram CO2 cartridges, as they cool down fairly quickly during rapid shooting.

The slightly heavier 2.8-gram black rounds were also used for some of the shots, which can contribute to minor changes in velocity compared to the lighter 2.6-gram rounds.

Even with that drop, performance was still strong and suggests the TC68 could likely reach high-400 fps velocities with a fresh CO2 setup or an 88-gram CO2 cylinder, which provides much greater gas capacity and improved consistency.

View fullsize

Accuracy Testing

For the accuracy portion of the test I set up a paper target down range and loaded roughly 20 rounds into the magazine.

The first test consisted of 10 shots in semi-automatic mode using the heavier black nylon rounds. A red-dot optic was installed on the TC68 for aiming, though it had not been sighted in or adjusted beforehand.

Results were quite respectable for a marker shooting heavy .68 caliber rounds.

• Overall grouping was approximately 4 inches

• Most shots landed within a 2.5–3 inch cluster

• One shot landed slightly low outside the main group

Considering the optic was not adjusted and this was essentially a right-out-of-the-box test, the accuracy was quite good.

Full-Auto Shooting Test

After the semi-auto accuracy test I attempted a full-auto burst test, but quickly discovered the CO2 had been depleted.

After installing fresh CO2 cartridges, the full-auto test was repeated with approximately 20 rounds loaded.

The TC68 does not have an extremely fast rate of fire, but it still delivers a solid stream of rounds when the trigger is held down.

View fullsize

During full-auto fire:

• The gun remained fairly controllable

• Rate of fire was moderate but effective

• CO2 cooling became noticeable during sustained bursts

A fresh target confirmed that the TC68 was still accurate enough for defensive-style shooting, keeping the majority of rounds within the main target area even during burst fire.

Power and Energy

Using approximately 2.8-gram nylon rounds traveling around 475 fps, the TC68 is producing significantly more energy than its factory-rated 16-joule output. Closer to 30 joules!

The modification performed simply allows the power adjustment screw to reach its full depth, allowing the marker to operate closer to its maximum potential.

While exact energy figures will depend on projectile weight and velocity, the TC68 in this configuration appears capable of producing considerably higher energy levels than stock, while still remaining under the 500 fps legal limit in Canada.

Shooting Impressions

Overall the Umarex T4E TC68 proved to be a solid and reliable platform during testing.

Some observations from the field test:

What I liked

• Strong velocity potential

• Good accuracy for a .68 caliber marker

• Full-auto capability for rapid follow-up shots

• Compatible with multiple CO2 power options

Things to consider

• Dual 12-gram CO2 cartridges cool down quickly

• Larger 88-gram CO2 cylinders will provide better consistency

• The gun includes multiple safety mechanisms that require familiarity

The TC68 includes three levels of safety, which helps prevent accidental discharge but does require some practice to become comfortable with the controls.

View fullsize

Final Thoughts

The Umarex T4E TC68 performed well in this field test.

Velocity was strong, accuracy was respectable for a .68 caliber marker, and the full-auto capability adds an interesting dimension to the platform.

With proper setup and a fresh CO2 source, the TC68 has the potential to deliver high-energy shots while still remaining within Canadian legal limits.

Overall it’s a very capable paintball / less-lethal marker and definitely an interesting option for those looking for a high-power .68 caliber platform.

• Buy the Umarex T4E TC 68 Less Lethal Paintball Rifle in Canada

• Buy Paintball Guns in the US

In this Table Top Review we’re taking a close look at the Sig Sauer P229 CO2 Blowback Pellet Pistol. This is the tabletop portion only, no shooting in this review as my Field Test Shooting Video will follow later on.

If you’re familiar with the Sig Sauer ASP P226 platform, the P229 version is the same general system in a more compact package, with one major upgrade: it’s optics-ready!

View fullsize

Specifications

• Manufacturer: SIG SAUER

• Power Source: 12g CO2

• Ammunition: .177 pellets (also supports steel BBs)

• Action: Semi-auto, blowback

• Trigger: DA/SA (double action / single action)

• Magazine: 16 rounds (twin 8-shot rotary clips, loaded on both ends)

• Barrel: Rifled inner barrel

• Sights: White dot sights

• Safety: Manual safety lever with de-cocker function

• Claimed Velocity: up to ~380 fps (real-world varies with temperature and cadence)

• Shots per CO2: roughly 50–60 (varies with temperature/cadence)

• Weight: 35.2 oz / 1.0 kg (2.2 lb)

• Overall Length: 7.7 in (P229)

• Optics: optics-ready slide / SIG AIR reflex-sight mounting provision

• Muzzle threads: M14x1 CCW

View fullsize

In the Box

• P229 CO2 blowback pellet pistol

• Manual

• Sight/plate parts for the SIG AIR reflex mounting setup (for red dot use)

P226 vs P229 - What’s Different?

These two share the same general operating system (CO2 blowback, DA/SA, rotary-mag that works with pellets/BBs), but the P229 version changes a few important things:

View fullsize

Key Differences

• Size: P229 is shorter (7.7 in) vs P226 (8.25 in).

• Weight: P229 is lighter (35.2 oz / 2.2 lb) vs P226 (~39.1 oz).

• Optics: P229 is optics-ready (SIG AIR reflex mounting provision); P226 platform is typically not.

• Muzzle threads: P229 uses M14x1 CCW (P226 commonly uses a different thread direction/size).

Bottom line: if you liked how the P226 handled and performed, the P229 should feel very familiar, just more compact, with the bonus of being set up for a dot.

Walk-Around & Handling

The P229 has that classic SIG profile and a very “real pistol” feel in the hand, helped by the mostly-metal build and full weight.

View fullsize

Notable features and controls:

• DA/SA trigger system: long/heavier first pull in double-action, then lighter single-action after the slide cycles.

• Safety + de-cocker lever: functions like the real-steel concept — you can decock the hammer and run it DA/SA.

• Accessory rail: for a light/laser (training-style setup).

• Optics-ready slide: set up to accept the SIG AIR reflex-style mounting system (sight sold separately).

CO2 System and Magazine Notes

One of the standout features on this platform is SIG’s cam-lever, tool-less CO2 loading system, designed to make cartridge swaps quick and easy.

The magazine is a 16-shot design using twin 8-shot rotary clips. Practical tip: make sure pellets are seated properly in the rotary clip so they don’t hang up during cycling.

View fullsize

Pros

• Mostly metal build with realistic weight and solid feel

• Compact P229 size (shorter than the P226)

• DA/SA trigger + functional safety/de-cocker system

• Blowback action for realism/training value

• Rifled inner barrel (pellet accuracy potential)

• Tool-less cam-lever CO2 loading system

• Optics-ready slide (big upgrade over older-style setups)

• Accessory rail for light/laser

Cons

• Fixed/non-adjustable sights

• CO2 performance is temperature + cadence sensitive (rapid fire cools the system and drops power)

• No last-round hold-open on this style of rotary-mag system

• Rotary clips require good pellet seating to avoid occasional feeding issues

View fullsize

Final Thoughts

The Sig Sauer P229 blowback pellet pistol is a very “SIG-like” training/plinking platform: realistic controls, DA/SA operation, snappy blowback, and a compact duty-pistol footprint. The biggest tabletop takeaway is the optics-ready slide, which makes this version feel more modern than older CO2 pellet pistol designs.

Field test shooting (chronograph + accuracy) will follow in the next video.

Available in our Canada Replica Airguns Store. Also check out:

• Buy the Sig Sauer P229 in Canada

• Buy the Sig Sauer P226 in the US

View fullsize

We didn’t catch this one at the Steambow booth, we were out at the SHOT Show indoor range checking out Steambow again, Tyler walked us through their brand-new-for-2026 B08: a magazine-fed .68 caliber ball launcher/crossbow that’s just starting to hit availability.

• New B08 .68 cal “ball launcher” platform (2026): This is a .68 caliber system designed to run .68 spherical projectiles (paint, foam/nylon, and pepper/irritant-type balls were all discussed as compatible options, depending on local rules).

• 8-shot, removable, pre-loadable magazine: The B08 uses a spring-fed 8-round magazine that inserts at the front. Tyler’s demo made it clear you can pre-load multiple mags and keep shooting quickly.

• Simple, repeatable action (easy to learn fast): The manual of arms is very “repeat-and-go”: load the mag, cock it, shoot, then cycle and repeat. Steambow describes the system as their familiar AR-Series quick-tilt/quick-clamp style for fast reloading.

• Ships mild, but can be upgraded for more power: The one I tested was using a 35 lb limb, but it’s built to accept other AR-Series limbs (stronger options sold separately). Tyler specifically said swapping to a much heavier limb can turn it into a high-velocity setup (he referenced up to a 150 lb limb and around 300 fps in his talk).

• Projectile flexibility is the whole point: If you already have .68 cal paintballs or similar at home, that’s the target “ecosystem” this is built around (so long as they’re spherical).

• Important safety + legal reality check: Steambow is very explicit that once you move beyond the “low power + soft balls” envelope, the B08 can become very dangerous, they warn that harder/heavier projectiles (including steel balls) raise risks like severe injury/lethality and ricochets, and that irritant/pepper-type rounds may be legally restricted depending on country.

Tyler’s range demo made the main selling points obvious: magazine speed, easy operation, and a huge range of .68 ball options. If we can get it lined up for Canada, it looks like a very versatile multi use platform, especially for anyone who wants .68 cal fun adn then some, without relying on CO2 or HPA.

View fullsize

In this Field Test Shooting Video I take a look at the KJ Works KP-19S. I’ve reviewed the KP-19 in the past, so this one should perform similarly, but it’s been a while and I wanted to get this one out for a proper range session.

I’ve already done a tabletop / close-up video for the KP-19S covering the specs, features, and up-close details, so if you want the full walk-around and all the technical info, make sure you check that out first.

For today’s session, I focused strictly on performance in the same basic field-test format: velocity testing, then a 10-shot accuracy group at 30 feet, and finally some overall shooting impressions.

Velocity Testing (Chronograph)

For the chronograph test, I ran 0.25g Airsoft BBs (not 0.20g), so expect the readings to come in a bit lower than what many people quote online.

My chronograph also decided to be difficult today, throwing “Error 2” messages and not registering shots consistently, so I had to keep working at it until it finally started giving me some readings.

Once it cooperated, I got five velocity readings:

• 312 fps, 304 fps, 293 fps, 288 fps, 284 fps:

• Average of 296 fps

A couple notes to keep things fair:

• If I had started the test with zero shots fired beforehand (the way I normally try to do it to maximize “fresh CO2” performance), the first shots could be a bit higher.

• Because this was with 0.25g BBs, if you ran 0.20g BBs, you’d likely see higher numbers, potentially into the low-to-mid 300s depending on conditions.

• This model also includes an extended barrel option that can push velocity higher, but I didn’t test it that way because most people run the pistol in its standard configuration (without a long exposed barrel sticking out).

Accuracy Testing (30 Feet)

For the accuracy test, I put a paper target at 30 feet and fired 10 rounds. The nice thing here is that the pistol should lock back on the last shot, so it makes it easy to confirm you’re done without having to count.

Results were excellent for a quick out-of-the-box test:

• With the exception of one flyer, everything was within about an inch

• The group was well-centered left-to-right

• Elevation was also very good without any sight adjustments

There isn’t much you can do for sight adjustment on this one unless you add a laser or optic, but you can tweak elevation slightly via hop-up, depending on your setup.

View fullsize

Final Thoughts

This pistol performed really well for me today.

The KJ Works KP-19S has that 1911-style trigger feel, light, short, and responsive, paired with a snappy blowback that makes it fun to shoot. Velocity was consistent once the chronograph started behaving, and the 30-foot grouping was far better than I expected without any tuning.

Aesthetically, it’s also a great-looking gun: a tactical, modern two-tone style with a double-stack magazine look that gives it that “2011 / hi-cap tactical 1911” vibe. If that’s the style you’re after, the KP-19S is a strong choice.

It should also work with most KJ Works tactical 1911 / double-stack style magazines, so if you already own similar KJ Works pistols, you may be able to mix and match mags. You can also run green gas magazines, but velocity will generally be lower. If you do choose to run the extended / threaded barrel setup, you can hide it with a mock compensator, but it will turn the pistol into a longer, bulkier package. Personally, I prefer it in the standard configuration.

Where to Buy

You can check this pistol out in our Canada Store (and possibly the US Store, depending on availability). I’ll include links where applicable, along with general store links where you can browse airguns, BB guns, airsoft guns, pellet guns, blank guns, and accessories.

Thanks for watching and reading, don’t forget to subscribe, and follow us on Facebook, Twitter, and Instagram. And yes, we’re back on YouTube after being gone for years. We’re re-uploading older content from Vimeo manually, so it’ll take a bit to get everything restored, but all new videos should be going up on YouTube as well going forward.

View fullsize

I had the chance to take the KWC 18 CO2 Blowback BB Pistol out for some shooting today to see how it performs. It’s a Glock-styled 4.5mm steel CO2 BB pistol with full blowback and selectable semi and full auto. It’s not an officially licensed Glock, but if you own (or have shot) Glocks, the controls and overall feel will be instantly familiar.

I’ve already done a close-up tabletop video for the KWC 18 covering specs and details, so if you want the up-close visuals and feature breakdown, make sure to check that out first.

For this session I concentrated solely on performance: a quick 5-shot chronograph run in semi-auto to record velocity, a 10-round semi-auto group at 30 feet, and then a full-auto mag dump to get a practical feel for controllability and “real world” accuracy—right out of the box (no tuning).

Velocity Testing (Chronograph)

For the chronograph testing, I ran five shots in semi-auto with a brand new CO2 in the magazine. The numbers came in at 293, 294, 282, 290, and 282 fps, for an average of about 288 fps. The spread was tight and the pistol felt extremely “snappy” while shooting, there’s a lot of pop in the blowback and you can feel it cycling hard.

One important note: this is a single-action-only style system, so you do need to rack the slide to cock it before it’ll fire (ask me how I know…).

View fullsize

Accuracy Testing (30 Feet)

For accuracy, I put a paper target out at 30 feet and fired 10 rounds in semi-auto. After a quick adjustment (the pistol was hitting very low at first), I aimed higher and got a roughly 3-inch grouping. The group was well centered left-to-right, but the pistol was still shooting noticeably low overall.

This is the kind of thing you’d simply keep in mind while shooting, and depending on the setup, you may be able to tweak elevation a little (but with steel BBs at short range, don’t expect miracles).

Full Auto (Mag Dump)

Then I loaded up and did a full-auto mag dump. As expected, it was basically spray-and-pray at 30 feet. The rate of fire is insane, and between that and the strong blowback, it was extremely difficult to keep rounds on target. I may have only landed a couple hits on paper.

Final Thoughts

All told, the KWC 18 is a really fun Glock-style blowback BB pistol if you want something that feels familiar in the hand and delivers a crisp trigger with serious recoil-like blowback. In semi-auto it’s manageable (even if it shoots low out of the box), but in full auto, at least at 30 feet, it’s more about the fun factor than practical accuracy.

• Buy the 18 CO2 Blowback Steel BB Pistol in Canada

• Buy 18 CO2 Blowback Steel BB Pistol in the US store

This one’s really growing on me because it’s not your standard AR platform. We review a lot of AR-style rifles (and there’s nothing wrong with ARs, they’re popular for a reason), but this one has a very different vibe. It’s based on the SA80 British service rifle design and comes in a compact bullpup layout that gives you a long inner barrel without needing a long overall rifle.

Today’s Table Top Review is the G&G L85A2 (A2 version) ETU Airsoft AEG Rifle — and yes, a full Shooting / Field Test Video will be coming shortly. I definitely want to get this one out and properly test it.

This model is available in our Canada store. At the time of recording this review, it wasn’t available in the US store, but I’ll add an equivalent/similar US option (or a list of comparable AEG rifles) in the post links.

View fullsize

Specifications:

• Manufacturer / Distributor: G&G (Made in Taiwan)

• Replica Of: SA80 / L85A2 (British 5.56×45 NATO service rifle family)

• Platform: Airsoft AEG (Electric)

• Ammunition: 6mm plastic airsoft BBs

• Operation: AEG with simulated blowback (reciprocating bolt for a slight “tap” feel)

• Fire Modes: Semi / Full Auto (and programmable for 3-round burst via MOSFET programming)

• ETU System: Programmable MOSFET + Electronic Trigger Unit (ETU)

• Motor: High-torque motor (rated around 25,000 RPM)

• Gearbox / Internals: Full metal gearbox, heat-treated metal gear set

• Bushings: 8mm oilless bushings for smoother gear rotation

• Hop-Up: Adjustable hop-up (access via dust cover)

• Trigger: AEG electric trigger (single-action-only style in practical terms)

• Safety: Cross-bolt safety

• Sights: Metal, fully adjustable front & rear

  • Front: elevation

  • Rear: windage

  • Rear peep sight includes two aperture sizes

• Weight: 6.0 lbs (2.7 kg)

• Overall Length: 27.5 in (70 cm)

• Inner Barrel Length: 16 in (40.6 cm)

• Magazine: 450-round high-cap AR-style AEG magazine (AR/M4-style AEG mags should fit)

• Velocity: Approx. 370–400 FPS with 0.20g BBs (varies by setup/conditions)

• Top Rail: Yes (carry handle/rear sight assembly sits here; optics possible with a riser)

• Flash Hider: Metal AR-style, black (no orange tip on this one)

• Sling Mounts: Multiple mounting points; front appears reversible L/R, rear has mounts on both sides

View fullsize

Build Quality & Materials:

This rifle has a really solid, substantial feel and is nicely balanced. There’s a lot of metal here.

Notable metal parts include (from what you can see and feel):

• Upper & lower receiver areas

• Carry handle / rear sight assembly

• Front & rear sights

• Magazine (metal high-cap)

• Trigger guard (metal for sure)

• Barrel, flash hider

• Sling mounts, pins/screws, switches and assorted hardware

View fullsize

Polymer / rubber components include:

• Handguards

• Pistol grip

• Cheek rest area (polymer)

• Butt plate (rubber)

Overall: it looks great, feels great, and doesn’t feel “toy-ish” at all.

In the Box:

• G&G L85A2 ETU AEG rifle

• 1× metal high-cap magazine

• Cleaning rod

• Product brochure / extra paperwork

• Transport muzzle cover / cap

• Manual access via QR scan (links to G&G’s online manual)

View fullsize

Walk Around Notes:

A few highlights from handling it up close:

• Bullpup layout: compact overall, but the barrel/inner barrel length is still substantial.

• Sighting system: the carry handle doubles as the rear sight platform with flip apertures.

• Optics compatibility: you can mount an optic on the top rail, but you’ll likely want a riser so your eye line sits naturally.

• Dust cover + hop-up access: you can open the cover and access hop-up adjustments the normal AEG way.

• Charging handle note: my rifle did not come with the charging handle piece. I checked my unboxing footage and it wasn’t on there and it wasn’t in the box. It’s not essential for function, but at this price point it’s something you’ll want to confirm is included on yours.

View fullsize

Battery Compartment:

The battery area is under the handguard, and here’s the main downside:

• If you’re running a larger battery, you’ll likely need to remove hardware (including the sling mount and a bolt) to open the lower handguard section.

• With smaller nunchuck-style batteries, you may be able to fit them in with less disassembly, but bigger packs will probably require tools.

So yes: it works, but it’s not a quick tool-free battery swap design.

Quick Function Check:

I did a quick dry-fire demo using a 9.6V battery, and honestly it felt a bit underpowered/odd (some partial taps and inconsistent behavior). That could be the battery itself (mine was not great), but I would suggest this rifle will really come alive with a proper 11.1V LiPo and hope to use this setup in the field test video.

I’ve seen demos where the rate of fire is very high using an 11.1V setup, so that’s what I’ll be testing with for the shooting video.

View fullsize

Pros:

• Lots of metal in the construction with a super solid weight, feel, and balance

• Unique bullpup British-style rifle (not just another AR build)

• Simulated blowback adds a bit of feedback vs. standard AEGs

• Works with AR/M4-style AEG magazines (easy to find replacements/midcaps/highcaps)

• Good optics flexibility on the top rail (carry handle sight system included, or add your own)

• Programmable fire mode: Full Auto or 3-round burst

• No orange tip (and if you prefer one for visibility, you can always add your own)

Cons:

• Limited accessory mounting options (mostly just the top rail; not a modern “add rails everywhere” setup)

• Battery access can require tools and disassembly, especially for larger batteries

• Priced on the higher side (around $600+ CAD)

• My sample was missing the charging handle part, check yours when it arrives

View fullsize

Final Thoughts:

This is a really nice AEG. It feels premium in the hands, the two-tone green looks great, and it’s a cool change from the sea of AR platforms, while still keeping things practical with AR-style AEG mag compatibility.

The simulated blowback isn’t going to replace the feel of a true gas blowback rifle, but it’s a nice touch, and paired with the ETU/MOSFET system and upgraded internals, it helps justify why this model sits in a higher price bracket.

Next up: the field test / shooting video, ideally with a proper 11.1V battery so we can see what this rifle really does when it’s running at its best.

Availability:

• Canada Store

• United States Store

And remember we carry air guns, BB guns, airsoft guns, pellet guns, blank guns, and accessories in both our Canada and US stores.

Thanks for watching and reading! Don’t forget to subscribe, and follow us on Facebook, Twitter, and Instagram. More videos coming soon…

View fullsize

In this Table Top Review, we’re taking a detailed look at the KJ Works KP-19S CO2 Blowback Airsoft Pistol. I’ve already reviewed the standard KP-19 in the past, and while the two pistols share a lot in common, there are some important differences between the KP-19 and the KP-19S that are worth covering.

I’m not entirely sure what the “S” officially stands for, possibly Sport—but interestingly, I’d actually argue that the non-S KP-19 is the more competition-oriented version, especially for IPSC-style Airsoft shooting. That said, the KP-19S still offers excellent performance, strong build quality, and a feature-rich design.

As always, this is a Table Top Review only. A full Shooting / Field Test Video will follow later.

This pistol is currently available in our Canada Replica Airguns store, and if a similar model is available in the US store, links will be provided in the video description.

View fullsize

Specifications:

• Manufacturer: KJ Works

• Made In: Taiwan

• Power Source: 12g CO2

• Ammunition: 6mm Airsoft BBs

• Action: Semi-auto, full blowback

• Trigger: Single-action, skeletonized, adjustable (1911-style)

• Magazine: Full-size dropout metal magazine, 25-round capacity

• Weight: 1.96 lbs (890 g)

• Overall Length: 9.84 inches (250 mm)

• Inner Barrel Length: 4.25 inches (108 mm)

• Claimed Velocity: 366+ FPS

• Hop-Up: Adjustable

• Rail: Under-barrel Picatinny rail

• Sights: Fiber-optic front and rear

• Safety: Ambidextrous

• Magazine Release: Reversible

• Threaded Barrel: Inner and outer threading

• Field Strippable: Yes (1911-style takedown)

The pistol includes a removable inner barrel extension, which may be required to reach the higher advertised FPS—something we’ll confirm in the upcoming field test.

View fullsize

In the Box:

• KP-19S CO2 Blowback Airsoft Pistol

• Full-size metal CO2 magazine

• Inner barrel extension

• Allen keys

• Small bag of Airsoft BBs

• Instruction manual (Usually!)

The pistol comes packaged in a basic cardboard box, but all essential accessories are included.

KP-19 vs KP-19S – What’s Different?

The KP-19S shares most of its core design with the standard KP-19:

• Same frame, grip, slide profile, trigger guard

• Same skeletonized trigger and hammer

• Same magazine compatibility

View fullsize

Key Differences

• KP-19 (Non-S):

  • Flared magwell

  • Compensator

  • Removable rear plate for mounting a red dot

  • More competition-oriented configuration

• KP-19S:

  • No flared magwell (cleaner, more streamlined look)

  • Fixed rear sight

  • Two-tone appearance

Performance between the two should be nearly identical, and if you’ve already watched the field test for the standard KP-19, expect similar results from the S version.

Walk-Around & Handling:

The KP-19S is a large pistol with a fairly wide grip. Shooters with smaller hands may find it bulky, but balance and weight distribution are excellent. At just under two pounds, it feels solid without being overly heavy.

Notable features include:

• Slide cutouts on the top and sides

• CNC-style gold/brass-colored fluted barrel visible through the slide

• Fiber-optic sights that are extremely easy to pick up

• Ambidextrous safety

• Reversible magazine release

• Dual threaded barrel system (inner and outer threads)

The full blowback action is strong, crisp, and satisfying, with excellent slide movement and reset.

View fullsize

Field Strip:

Field stripping follows a classic 1911 takedown:

1. Align the slide notch

2. Push out the takedown pin

3. Remove the slide assembly

Once opened, you gain easy access to:

• Inner barrel

• Recoil spring

• Hop-up adjustment wheel

Reassembly is quick and straightforward, making cleaning and maintenance easy.

View fullsize

Pros:

• High metal content with excellent weight and balance

• Strong, realistic full blowback action

• Excellent fit and finish typical of KJ Works pistols

• High-capacity 25-round metal magazine

• CO2 or gas compatibility (with appropriate magazines)

• Dual threaded barrel for accessories and extensions

• Bright fiber-optic sights (easy to acquire on any background)

• Short, light, adjustable 1911-style trigger

• Ambidextrous safety and reversible mag release

• Easy field stripping and hop-up access

Cons:

• Grip is wide and may not suit shooters with smaller hands

• Higher price point compared to similar KWC 1911 models

• Rear sight is not adjustable and does not accept a red-dot plate

  • Optics would need to be rail-mounted from underneath

View fullsize

Final Thoughts:

The KJ Works KP-19S is a high-quality, full-featured CO2 blowback Airsoft pistol with excellent build quality, strong recoil, and competition-inspired styling. While it lacks some of the modular competition features of the KP-19 non-s version, it offers a cleaner, streamlined look and the same reliable performance.

If you’re looking for a quality CO2 Airsoft pistol with a fantastic trigger, solid blowback, and premium construction, the KP-19S is a strong contender.

A full shooting and field test video will be coming soon.

Where to Buy:

🇨🇦 Canada:
https://www.replicaairguns.ca/kp-19s-hi-capa-gbb-airsoft-pistol

🇺🇸 United States:
https://www.replicaairguns.us
(A similar model may be linked if the KP-19S is not currently available)

View fullsize

More Reviews & Articles

Visit our blog for written reviews, photos, and additional info:
https://www.replicaairguns.com

Thanks for watching and reading.
Don’t forget to subscribe, and follow us on Facebook, Twitter, and Instagram.

View fullsize

This isn’t an airgun, but it will show up in a least some of my airgun videos, you just won’t usually see it. The DJI Neo 2 is my new AI camera drone that I’ll be using for outdoor shooting segments, walk-around tests, and any time I need moving shots without a camera operator.

Up until now I’ve been using the original DJI Neo and the HoverAir X1 Pro Max. The HoverAir still has slightly better pure video quality, and the original Neo had decent AI features, but together they meant more gear to carry and more batteries to manage. The Neo 2 is the first drone that can realistically replace both for what I do on this channel.

I picked up the Fly More Combo, which includes the Neo 2, the RC-N3 controller, three batteries, a charging hub, and the antenna/transmitter module pre-installed. With three packs I can get roughly 35–40 minutes of real-world flying, which is more than enough to cover a shooting session.

View fullsize

The biggest upgrade over the original Neo is the two-axis gimbal. Instead of cropping the image to keep the horizon level when the drone tilts in the wind, the camera physically moves side-to-side and up/down. Combine that with updated processing and you get up to 4K 60 fps (and even 100 fps in 4K), which is perfect for smoother tracking shots when I’m walking, moving between targets, or doing action-style footage.

The Neo 2 is also loaded with sensors and obstacle avoidance: fisheye cameras on multiple sides plus a front LiDARunit. It does a great job of seeing trees, branches and other obstacles and routing around them, which is exactly what I need when I’m focused on shooting and talking, not flying.

View fullsize

For control, I can either use the phone app for quick AI “follow me” and smart shots, or the RC-N3 for longer-range, more traditional drone flying and higher altitude shots. There’s also a very cool gesture control system (I call it “Jedi mode”) where I can move the drone up, down, left, right, closer or further just by using hand signals, no need to stop recording or dig through menus.

Bottom line: you probably won’t see the DJI Neo 2 in many of my videos, but you’ll definitely see what it captures. It lets me add smoother tracking shots, aerial views and more dynamic angles to my Replica Airguns content, all without needing a dedicated camera person. For a solo creator who films a lot outdoors, it’s a very handy tool to have in the bag.

View fullsize

I tested another Steambow model in this Field Test Shooting Video, the Steambow AR Series M10 Tactical Crossbow. Like my other Crossbow Field Test videos, I recorded the Chronograph velocity while I was shooting the target so there was no need for separate segments, everything was done in one go with four cameras rolling. I didn’t put a dedicated camera on the Chronograph because I wanted a camera on the target; my camera glasses generally pick up the chrono readings anyway. I only have so many cameras, but everything recorded as planned. If you want the full specs and a closer look at the M10, watch my dedicated Table Top video.

Steambow quotes about 190–200 fps for the AR Series M10. My six chrono readings were 189, 191, 189, 189, 190 and 191, which worked out to a 190 fps average. Using the included 142-grain, 6.5-inch aluminum bolts produced roughly 11.4 foot-pounds of energy, so both velocity and FPE were basically on target with Steambow’s numbers. That’s adequate for small pests, but humane shots always come down to accuracy, you’ll want head or shoulder placement, and I’m not ready to declare any compact crossbow a guaranteed solution for that. Test accuracy for yourself.

View fullsize

For accuracy I shot six rounds at a paper target 30 feet downrange from my usual seated in the back, hands rested up front shooting position. The first shot from the Steambow AR Series M10 Tactical Crossbow was a few inches low, so I adjusted my point of aim up and ended up with an impressive 1-inch, 4-shot group just left of center. One bolt missed the target entirely, could have been me or a bad bolt (I’ll blame the bolt on that one). Still, for a compact crossbow this was an excellent result, comparable to some pellet rifles.

Overall the Steambow AR Series M10 Tactical Crossbow performed really well. I like the cocking and bolt-feeding system, cocking is simple: shoulder the stock, press the release, then pull the front down using the foregrip for leverage. Even with the higher power of this model you don’t need a lot of strength, and with practice follow-up shots can be quick. I’d add a red dot to the rail to help dial in accuracy and buy a few extra bolts for target practice and hunting. The M10 is one of Steambow’s pricier offerings, but it also has the highest ammo capacity and the most customization options. If you want the ultimate compact crossbow setup, the ability to preload multiple bolts and have extra 10-shot magazines on hand makes the M10 the one to consider.

• Buy the Steambow M10 Tactical Recurve Crossbow in Canada

• Buy Compact Recurve Crossbow in the US