Testing out the ASG - Marushin CZ 75 Blowback Shell Ejecting Airsoft Pistol was not an easy one but I did manage to get thorough it! First there was the setup, I could not shoot the ASG Shell Ejecting CZ 75 Airsoft pistol on my deck or I would have fore sure lost most of my shell casings for it. So I decided to setup camp in my pool area where I have a nice large flat area off to one side, I put down a ginormous tarp in hopes to catch the radically flying shells but even this failsafe did not catch them all as I later found out ;)
As with most of my Field Test Shooting videos, I usually do a bit of a pre test to make sure the gun is functioning properly and so I shot a full magazine of my brass shells through the ASG CZ 75 and it worked like a charm, of course when I started recording the live video it decided not to work at all and I still do not know why? I was able to revert back to the plastic shell casing that came with my ASG CZ 75 Blowback Shell Ejecting Airsoft Pistol and they seemed to be working so I went with them for my testing. Interestingly enough the brass shells got much higher fps (around 300+) when I did my pretest compared to around the 250 average fps I was getting with the plastic shell casings.
Shooting on target proved to be better than I though once I raised my sight point up a bit, the gun likes to shoot a bit low but once I found the sweet spot I got three rounds within about 3/4 of an inch from just over 20 feet away in a semi rested position.
I would not recommend this Airsoft gun as an everyday shooter and there is no way you could use it in any type of Airsoft simulation as the ejected shell casings would get lost for sure and the cost to shoot the ASG CZ 75 would get very high indeed! It would be good for use in a movie or video where you wanted the realistic look of shells being ejected and did not want to use a blank gun or render the shells in post. And of course it is just really cool to have an Airsoft gun that has ejecting shells :)
Materials: Plastic slide & frame, some metal parts.
Weight: 1.4 pounds (616 grams).
Barrel: Metalnon-rifled smooth bore.
Propulsion: Propane, green gas.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 8 rounds.
FPS: 279+ fps.
Trigger Pull: The trigger pull on the ASG CZ 75 Shell Ejecting Airsoft Replica is single action only, unlike the real steel version that actually has a single and double action trigger. The single action trigger has a light to medium pull but does have a fair bit of take-up to it.
Accuracy: I did not pre-test the ASG CZ 75 as the shells fly everywhere and you really need to be able to retrieve them afterwards as the cost to replace the shell casing is rather high. I do plan to do a full Shooting Field Test where I will shoot the ASG Shell Ejecting CZ 75 through the chronograph, place some shots on a target and also capture the action of this pistol in slow motion with a high speed camera. So stay posted for that. I can say that from the few shots taken in my house, that it seems to shoot pretty hard and the shells really com flying out of this gun with force, I also noticed that a BB does have to be loaded into each shell for there to be enough back pressure to allow for a full slide blowback and ejection of each shell.
Build Quality: Even though this gun is made mostly out of plastic and from what I can tell is also made in Taiwan, it has a very good overall fit and finish. The slide slop is next to none and the licensing and markings look great. There are metal parts where they really need to be like in the barrel, hammer, trigger, safety, slide catch, magazine and a few other internal parts.
Realism: The ASG Shell Ejecting CZ 75 Airsoft Pistol is one of the most ultra realistic Airsoft pistols I have seen and mimics a real steel gun right down to the shells being ejected, how cool is that! If it had more metal then that would really top it off. Even with the plastic slide and frame it is very realistic in almost every way and even field strips just like a real CZ 75 and is fully licensed. The only feature not true to the actual CZ 75 would be the single action only trigger.
Excellent fit and finish - tolerances are very good.
Very believable working replica of the real steel CZ 75.
Fully licensed.
Fully field strip-able.
Nice heavy full size drop out metal magazine helps give it some needed weight.
Has metal parts where they need to be.
Cons:
Plastic slide and frame.
A bit low in the FPS department.
Only 8 rounds in the magazine.
Can not really use in the field, would lose too many shells.
Comments:
The ASG CZ 75 Shell Ejecting Blowback Airsoft Pistol is a very unique Airsoft gun, not very many Airsoft guns actually have ejecting shells. Just because of that I had to have it! Overall it is a pretty decent gun but I have yet to really test it out and that is the biggest shortcoming with this gun, you can't just shoot it anywhere as you need to shoot it in a place where you can recover your spent shell casings, unless of course you have all the money and shell cases in the world... That said it has a lot going for it other than the ejecting shells; Fully licensed and trademarked, blowback operation, full size drop out metal magazine and it's fully field strippable. I am sorry to say we don't offer it in out Canada or USReplica Airguns Store but we do have a similar all metal CZ 75 Airsoft offering in the form of the KJWorks KP-09 which I have done both a Table Top and Shooting Review for.
Materials: Metal and plastic (polymer) construction.
Weight: 1 pound 10.5 ounces (752 grams).
Barrel: 3.3 inches, metal rifled.
Propulsion: CO2 x 1.
Action: Semi auto, single and double action.
Ammunition Type: .177 caliber pellets
Ammunition Capacity: 8 shot rotary magazine.
FPS: 360.
Trigger Pull: The trigger pull on the Umarex Walther CP99 is in the mid range for it's double action trigger pull with most of the effort at the beginning and middle stages as it cocks the hammer and indexes the rotary magazine, it does have a predictable release point making it easy to put pellets on target. By racking the rear slide you can put the CP99 in single action mode which makes the trigger pull much lighter and great for very accurate shots.
Accuracy: I shot this air pistol at a target from 20 feet away in a free semi rested position and it performed well getting a nice tight one inch eight shot grouping just to the left on the target. The sights can be adjusted for windage if your aim is off to one side or the other. With my preliminary Chrony Chronograph testing using 6.9 grain RWS lead pellets I got pretty close to the factory claim of 360fps with an average of right around 346 fps.
Build Quality: The Umarex Walther CP99 is a metal and polymer air gun with a good deal of metal components on the inside giving the Walther CPSport a decent overall weight and heft. It's worth mentioning that the Walther CP99 has a full size drop out magazine for holding the CO2 cartridge that gives the air gun some additional weight and functionality. The German made fit and finish is very good on the CP99 and the plastic quality is also very good.
Realism: The Umarex Walther CP99 is licensed by Walther and is based around the Walther P99. The frame is very similar to the P99 but the slide is not as accurate in terms of the real steel but you can definitely tell the Pellet shooting CP99 is a copy of a Walther P99. One of the biggest shortcomings is the safety, the real P99 does not have a safety but Umarex decided to put a rather large safety on the right hand slide area. I do however like the working de-cocker, slide catch for loading magazines and full size drop out magazine which give the Umarex CP99 a more realistic look and feel.
Slide catch and de-cocker are realistic and functional.
Rifled barrel.
Sights are adjustable for windage.
Slide catch and magazine release are fully functional.
Nice full size drop out CO2 magazine.
Good combination of power, accuracy and CO2 efficiency (I got about 100 shots from a CO2)!
Rail for accessories.
Walther licensing.
German Quality.
Cons:
Up in the higher price range.
Double action can have some stickier shots.
Kind of funny safety, not true to the real steel Walther P99.
No recessed barrel
Comments:
The Umarex Walther CP99 Pellet CO2 Air Pistol is a nice step up from the Walther CPSport I reviewed earlier. The CP99 is a much more accurate looking replica of the P99 and it also has more metal parts and a single and double action trigger. These added features do come with an additional $100 price tag but in my opinion are worth it. If you're a fan of the Walther line of pistols than you should probably take a look at the Umarex Walther CP99 as it would make a great addition to your airgun collection.
I don't often get to shoot my airguns out at the 100 foot mark but I purchased my Sheridan Silver Streak .20 Caliber Multi Pump Pellet Rifle mainly to shoot up to and even past this fairly distant range as the Silver Streak is my new vermin gun for pests around the farm. I get a lot of Crows that to be honest are just feathered bullies that pick on all the other friendly birds on the farm, they have also been known to get into my garbage and even attack the Eagles and Hawks in the area. Flying Rats I like to call them.
In this Field test Shooting video I test out my brand new Sheridan Silver Streak on the Chronograph to see just how powerful it really is not just at the maximum 8 pumps but also at 3 and 5 pumps. I was actually very surprised at the very decent power I got from only 3 pumps (460 fps), you could easily take out a small rat with the 14.3 grain .20 caliber lead pellets I was using for my Chrony test. At 5 pumps I gained close to another 100 fps and at 8 pumps I maxed out at just a hair under 640 fps respectively. With the 14.3 grain pellets I was using this worked out to right around 13 foot pounds of energy. (My Sheridan was purchased using a PAL)
I also shot my Sheridan Silver Streak .20 Caliber Pellet Rifle at a target setup 100 feet or just over 30 yards away and was able to get what I felt was a nice 1.5 inch 5 shot grouping. 4 of the 5 pellets where all within 1 inch of each other with my first shot being a bit lower and to the right of the rest spreading the group out to about 1.5 inches. Keep in mind I was also a bit winded from all the pumping and I could feel and see my heartbeat in my 9 power Bushnell scope making my crosshairs bob back and forth ever so slightly.
I have not shot my Sheridan Silver Streak all that much and plan to hone my skills further so when the time comes I will be ready for them pesky crows.
Stay tuned for my future Table Top review of my Sheridan Silver Streak, for now you can checkout my Preview video that has some preliminary info.
For the most part, this video is to test out some cameras and using them all together in a multi-camera scenario. I wanted to see how many camera angles I could shoot at one time and see how they would all work together when editing the video.
Cameras used:
My new Pivothead Recon Camera Glasses.
Sony HDR-AS15 Action Cam.
Drift HD170 Point of View Camera.
Nikon 1 with 10mm fixed lens.
Casio TRYX.
*All cameras where shooting in 1080p for this video.
I hope to use camera setups like this in the future, maybe not all at once but at least a couple at a time to give you some viewing options.
I picked out my WE SCAR GBB Airsoft Rifle for this test as it had a lot of mounting points and the Gas Blow Back makes for some great video action. Unfortunately My WE SCAR was not working at 100% but I still think I was able to pull off this test video either way.
Watch my Multi-Camera-Angle Test Video shooting the WE SCAR GBB AIrsoft Rifle:
ALL GUNS ARE NOW SOLD - THANKS FOR THE AWESOME RESPONSE!
This is a first for me but I guess you could say I have to make room for some more guns ;) I have some duplicate guns and a couple I juts don't have a need for anymore so instead of having them sit around collecting dust, I thought I would offer them up for sale and get them in the hands of someone who can really appreciate and get some use out of them...
Here is a list of the items up for sale:
Baikal IZH-61 .177 Caliber Spring Piston Pellet Rifle: $115
Baikal MP-655K Pellet/BB CO2 Pistol (missing pellet magazine): $125
Umarex CP99 Compact CO2 BB Blowback Pistol: $50
Swiss Arms Sig Sauer GSR 1911 CO2 BB Pistol: $30
ASG CZ 75 P-07 DUTY Dual Tone CO2 BB Blowback Pistol: $125
Umarex Beretta M92FS .177 Caliber CO2 Pellet Pistol - Nickel with Wood Grips: $200
(2x) AK47 BB Gun Magazines: $50 Each
Crosman 2240 .22 Caliber CO2 Pellet Pistol (14 inch barrel, RJMachine Breach/Brass Bolt, Wood Grip, NcSTAR 6x32 Scope): $225
Shipping/Handling is $15 Canadian and $25 to the US and you must be 18 or over to buy. You will need to email me at mike@replicaairguns.com to let me know what gun/guns you want to buy - first come first serve, I will send a PayPal request to the person with the first offer to buy and give them 24 hours to pay or I move on to the next buyer.
You can watch my YouTube Video to get a good look at each pre-owned item up for sale:
I like to show off some of my acquisitions from time to time even if they are guns I don't necessarily have for sale, I am a collector and some items are not always common enough or even popular enough to keep in our Replica Airguns Store.
Today I show you two blank guns I picked up from a recent gun show I attended in Chilliwack BC. There where not many blank guns at the show, the two I found may have been the only blank guns there, at least that I saw? The ROHM RG300 .22 Caliber Blank Pistol and RST MOD. 1966 .22 Caliber Blank Revolver I picked up for a pretty good price, at least in my mind, $55 for the ROHM and $20 for the RTS. A nice addition to my blank gun collection!
I have been contemplating between a PCP (Pre Charged Pneumatic) or a really good Multi-pump air rifle for pest control around my house, I have been using a spring piston rifle but the combination of my limited skills with spring piston rifles and the fact that most pests in my area stay a good 50+ yards back, means I need an airgun with pin-point accuracy. At the end of the day I decided on the Sheridan Silver Streak because it was a bit more affordable than a PCP air rifle and also the Sheridan is such a classic air rifle but still with the right amount of power and accuracy to get the job done.
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
Trigger Pull: The trigger pull on the KJWORKS KP-09 CZ 75 Airsoft Replica is surprisingly light in single action but incredibly sticky at first in double action, with that said you really will not be shooting very often in double action unless you happen to de-cock the gun for some reason, at least you have the ability to shoot with the hammer down in double action when required. In signal action it took me a bit to get used to the very light trigger pull as I was letting some shots go off early.
Accuracy: I shot the KJWORKS KP-09 from 20 feet out in semi rested position and got very satisfactory results. I was able to place 10 rounds under 2 inches almost getting a 1 inch group with the exception of one flyer. Shot placement was also well centered but just a bit high which could easily be corrected by adjusting my aim point just a bit down. The KJWORKS CZ 75 Airsoft Replica shot right around the 360 fps range while conducting my 5 shot average chrony testing which is right where this gun is supposed to be. I also got three full 24 round magazines worth of shots with a bit of CO2 left over for a partial mag, so this gun can easily get 75 shots out of a 12 gram CO2 - not bad at all for this style of full heavy blowback airsoft design.
Build Quality: I am extremely impressed with the build quality of pretty much all the KJWORKS Airsoft guns, the fit and finish is the best I have seen on any of my guns including my 4.5mm steel BB shooters. Even after shooting several magazines worth of BB's, the painted metal friction areas show very light wear which is not always the case with metal built blowback airguns. (there was some wear present within the ejection port but this is common even with real steel guns as metal on metal will wear down the finish). The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining.
Realism: The KJWORKS KP-09 6mm Airsoft pistol is a replica of the real steel CZ 75 and is a great looking and functioning copy. You will not find actual licensing on this version and the CO2 magazine does stick out a bit to accommodate the 12 gram CO2 but other than that this Airsoft pistol looks and works near exactly like the real mccoy and is full field strip-able. Even the safety operates just the same with safety available on half cock and full cock only.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Excellent fit and finish - best I have seen.
Excellent fps and CO2 efficiency (three plus full 24 round magazines)
Good accuracy and well centered on target.
Very believable working replica of the real steel CZ 75.
Fully field strip-able.
Cons:
Does not have official CZ 75 licensing.
CO2 magazine is long to accommodate the 12 gram CO2.
Did get some finish wear in the ejection port area.
Comments:
The KP-09 CZ 75 is another wonderful full blowback Airsoft pistol from KJWORKS. The CZ 75 is a classic semi auto pistol and deserves the attention to detail the KJWORKS version demonstrates. I found the CO2 usage to be very good on the KP-09 considering the rather high 360+ fps I was abel to get with it. Top this off with high marks in the accuracy department and you have a real winner here. So if you're looking for a quality Airsoft Replica of the classic CZ 75 that shoots straight and hard and looks and operates just like the real steel version then the KJWORKS KP-09 should just do the trick for you.
Here's a heads up on some new items we will be adding to the Canada Replica Airguns Store very soon so keep checking back if you're interested in them!
Your best bet is to Watch My Vimeo Video as I go over them all and show you around the new products, but for now here is some basic info on each item:
I am happy to report back to you on all the new cool stuff I got to see at this years 2013 SHOT Show in Las Vegas. Make sure to also watch my Vimeo video at the bottom of this post for some first person styled play by play of my experience at the Vegas SHOT Show 2013. (like you're there with me ;)
First up I want to cover a new gun from ASG, I have been wanting to get my hands on the 4.5mm Bersa BP9CC and I finally got to, not only did I get my hands on it but ASG was kind enough to supply me with one to take home for review. You can get the Bersa BP9CC in both Blowback and non-blowback versions and also in either BB or Airsoft. I opted for the 4.5mm BB Blowback version. I will be reviewing this BB gun very soon!
ASG also had a very cool prototype of an Airsoft CZ Scorpion EVO 3A1 hopefully coming out soon.
While roaming around SHOT Show 2013, I came across an interesting booth from FlashFog Security. I often get people asking me about using an airgun as a home defense weapon and I strongly advise against this. If the intruder is not scared off by the gun there is little an airgun can do to actually stop them. The FlashFog system works by rapidly filling a room with dense fog combined with a strobe light effect which blinds and disorients intruders completely. There is little an intruder can do other then try and get the heck out of there!
UPDATE: FlashFog just added a new section to their website specifically for School Security to help keep our schools safer from potential safety threats! So check it out: School Security Smoke Screen
I was a bit surprised by Gamo this year, they tend to stay away from actual Replica's and generally make BB/Pellet guns that look like popular guns but not any gun in particular. Gamo has a new BB/Pellet MP9 based machine pistol that uses a similar mechanism to their P-25 and PT-85 so it can shoot both 4.5mm BB's and .177 caliber Pellets using a double ended 16 shot rotary magazine. It also has an internal blowback system so it should have some recoil feel to it! I am pretty sure it is semi auto only but still a nice addition to their lineup!
Gamo also brought out a new 4.5mm BB Blowback pistol called the C-15 which has a metal slide and plastic frame, it kind of reminds me of the Umarex HPP in how it looks and feels.
Umarex had several new products that I am sure everyone is going to like! One that I think will do really well is the Steel Force, the Steel Force is designed around the 4.5mm BB shooting Steel Storm platform so it has a 6 round burst blowback operation and holds the 2x12 gram CO2 in the magazine while the BB's go in a 300 round hopper that feeds into a 30 round spring fed internal magazine. Like the Steel Storm it will shoot around 430 fps. The Steel Force has the advantage of being styled after the AR platform so it has a collapsible stock which will make shooting very easy.
Another often asked for airgun replica is the historic German Luger. This year Umarex stepped up to the plate and introduced the Umarex P.08 4.5mm BB pistol. Sorry, no blowback or even a working slide on this one but it is all metal and has a very good weight and feel to it.
If you're a fan of the entry level Umarex XBG then you may be interested in the new Umarex T.D.P. 45 which is very similar to the XBG in looks and features but with a slightly different look to it.
If you've ever wanted to turn your pistol into more of a PDW styled gun, you may be able to depending on which Umarex gun you have? Umarex added a very cool accessory called the T.A.C Converter that converts your Umarex HK USP (BB-Airsoft), SW MP40 (BB), XBG (BB), CZ Enforcer (Airsoft) and Walther P99 DOA (Airsoft) into more of a tactical (PDW) or Personal Defense Weapon complete with for-grip, adjustable rear sight, lots of rail options and a foldable stock.
I am assuming the Crosman M4-177 Pellet/BB Rifle has been doing well for Crosman as they have expanded with some more similar assault styled air rifles. The Crosman MSR77NP pretty much looks like a classic M16 but is in fact a Nitro Piston break barrel pellet rifle able to shoot .177 caliber pellets at 1200 fps (I hope there is a 499 fps Canada version planned too?).
A new takeoff of the M4-177 is the MK-177 which also shoots .177 caliber pellets and 4.5mm BB's using a multi-Pump System but it uses an upgraded more efficient pump system that squeaks out more fps with less pumps. The Crosman MK-177 is designed after the FN SCAR and is available in an adjustable iron sight version or a Red Dot equipped kit version.
One thing you can never get enough of in my opinion is another 1911 pistol! Crosman is introducing their GI Model 1911BB Blowback 4.5mm CO2 pistol, the one they had on hand was more of a prototype so the slide was not operational but it will feature an all metal design, blowback operation, 450 fps and a 20 round drop out magazine. I am sorry to say but it looks like the Crosman C51 has been dropped from Crosman's lineup but if you want a similar styled gun you can checkout the KWC SW40F which is a very close airsoft version.
We recently started carrying G&G Armament Airsoft guns, you can checkout my review of the Xtreme 45. I did stop by their booth and they had some new products on display, the M1 Grand (all wood stock) Airsoft had it's magwell all wrapped up as G&G had a propriety magazine system they did not want their competition to see. G&G also had some very interesting targets that light up, when shot they would react by individually turning off so you could see if you hit it or not.
There was a rather large crowd at the KWA booth but it was a shared booth so it's hard to say what everyone was looking at, the KWA area was pretty full, I did talk to the KWA rep and asked him point blank if KWC and KWA where the same or sister companies and the answer was not at all. There are often a lot of guns that look like they could be from the same company, I guess there is a lot of copying going on ;) One gun from KWA I would love to get my hands on is the Kriss SMG!
Now keep in mind many of these guns I have highlighted today are not available yet and a lot of them should be coming out in the spring time frame so please try to refrain from repeatedly asking when I will review them and have them in the store, it takes time and as much as we all want them now, they get here when they get here!
Watch my Vimeo video of the Replica Aiguns at SHOT Show Vegas 2013
I've already done a KJWORKS review on the KP-02, KP-07 and Elite 1A and they turned out to be very high quality Airsoft pistols so the extra price does get you a higher quality gun. So in this preview we are simply looking at some more models that from the looks of things I expect to be more of the same in terms of high quality and excellent functionality.
The KJWorks models we are looking at today are the KP-05 (1911 HI-CAPA), the KP-09 (CZ 75) and the M9 (Beretta M9). Even though none of them are licensed, they are very detailed and realistic copies of the original real steel versions with full blowback operation, heavy metal drop out magazines and lots of metal throughout. You would be hard pressed to tell them apart from the real powder versions.
All version in this preview load CO2 in the magazine along with 6mm Plastic Airsoft BB's, none of them have any orange markings or translucent parts as they fall into the uncontrolled firearms category here in Canada.
I look forward to doing my full review of these three very nice KJWorks Airsoft pistols.
In this part of the review I test the Smith & Wesson 357 CO2 Pellet Revolver using my Chronograph to see what the 5 shot feet per second average is using a brand new CO2. I got pretty close to the factory (even a bit over) claimed 425 fps using RWS 7 grain lead pellets on this rather cold day so you can expect better fps on a nice warm summer day.
I also take the Smith & Wesson 357 686 CO2 Pellet Revolver back 30 feet and shoot it at a target using a semi rested position (sand bag up front, standing in the back) and again although I did not get teh same half inch grouping I got in my preliminary testing, I did manage to get a nice tight grouping , keep in mind the Umarex Smith & Wesson 357 is an action shooter but is capable of target pistol like accuracy.
All in all the Umarex Smith & Wesson 357 686 CO2 Pellet Revolver performed very well. That said I was able to get tighter groups and higher fps so expect this Umarex high grade CO2 pistol to perform very well for you.
Watch my Field Test Shooting Vimeo Video Review for the Umarex Smith & Wesson 357 686:
It would not be the end of another year without another Airgun, Airsoft Gun and Blank Gun Collection video for you. This year I'm not showing all my guns, I started to take them out and quickly realized there where just way too many and this years video would have been several hours long and would have taken most of the week for me to shoot and edit...
So this year I have hand picked some of my top favorites and most notable replica Airgun, Airsoft Gun and Blank Guns. They may not all be the best made or hardest shooters or even all that accurate but each one has some significants to me.
Trigger Pull: The trigger pull on the Umarex Smith & Wesson 357 686 Revolver is very light and smooth in both single and double action. Single action is much shorter and a bit lighter with just a very short take up to it. In double action it does get a hair heavier and much longer as is expected but still very usable and easy to shoot quickly and with accuracy.
Accuracy: I found the Umarex S&W 686 pellet revolver to have some of the best accuracy I have tested out of a pistol, getting about a half inch grouping from 30 feet out in a semi rested position (sand bag up front, standing in the back). I also put 5 rounds through my Chrony Chronograph and the Umarex 357 686 averaged right around 450 fps using RWS 7 grain lead pellets which is even better than the claimed 425 fps from Umarex.
Build Quality:The Umarex Smith & Wesson 357 686 CO2 Pellet Revolver is almost entirely metal with the acceptation of the rubber grips and front removable sight, it has a very substantial overall weight and feel to it coming in at just under three pounds. Keep in mind this is one of the higher end German made Umarex guns and you can tell in the workmanship and fit and finish. All the mechanical parts work flawlessly and have very tight tolerances, the finish is also superb. Yes the price is up there but this is a an airgun you will most likely be passing down to future generations one day as a collectors item, and I would imagine also in working condition.
Realism:The Umarex S&W 686 is a replica of the real stell Smith & Wesson 357 Magnum and overall looks pretty similar in shape and style. It would have been nice to have seen a full swing our cylinder but this would have meant a more complicated design with potentially less performance? In a perfect world, loadable shell casings like the Dan Wesson would have been very cool but keep in mind this is an airgun that really performs in terms of power and accuracy. Mine was the silver version, I would have liked to have seen a color matched magazine but since it is metal it could be color matched after the fact. The Smith & Wesson licensing and markings along with the heavy weight, hidden CO2 Tab and recessed barrel help to give the Umarex S&W 686 a very believable look and feel.
Pretty much all metal, has a nice solid feel and good weight.
Higher than claimed fps (right around 450 fps)
Amazing accuracy, one of my best pistols tested to date.
Very high quality German made workmanship.
Very comfortable rubber grips.
Fully adjustable rear sight (windage and elevation).
Well hidden CO2 tab.
Full S&W licensing, good overall replica.
Single and double action with a nice trigger in both SA and DA.
Magazines are removable for easy loading and have a high 10 shot load capacity.
Cons:
A bit on the expensive side of things.
Rotary magazine is not color matched on the Silver version.
On the low side of shots per CO2 (About 60-70).
No rail mount for a accessories of any type.
Comments:
The Umarex Smith & Wesson 686 CO2 Pellet Revolver is not for everyone and I say that because the $250 plus price point is going to be just too much for many buyers. If you can find a way to get past the price then you will have a very high quality German made air gun on your hands, not only are the Smith & Wesson 568/686 CO2 Pellet revolvers very well made but they also perform as good if not better in terms of accuracy and velocity then even some dedicated target air pistols I have tested. Looks will not let you down either and I would not be surprised that this gun if well taken care of can be passed down to future generations as a working collectors item. If you are looking for a high quality, excellent performing replica pellet revolver then make sure to consider the Umarex Smith & Wesson 586 and 686 line of CO2 replica pellet revolvers.
Sometimes we all get caught up in which gun is brand new and has the most realistic features. I wanted to put the focus back on a few high quality German made Umarex Airguns that where designed from the ground up to be very good replicas but also take into consideration that yes, they are airguns and so they should be designed to operate like an airgun and have excellent build quality, and performance. Quality and performance sometimes gets sacrificed on newer guns that just go after realism and can sacrifice form over function.
Sure these German made Umarex air pistols are not cheap, but hold one in your hand and shoot it and you will quickly see that they are built to last a lifetime, these guns are an investment!
I have already reviewed the Colt Government 1911 A1 (Satin version), I wanted to also show you how it looks in the all black model. Two other Umarex German made guns I have been asked often to review are the Walther CP99 and Smith & Wesson 586/686 Revolvers. I am happy to inform you that I have these guns on hand and will be reviewing them shortly for you.
You can watch my Update video to see a bit of a preview of these very fine German made Umarex pellet shooters:
This Update video addresses the similarities between the KWC and Cybergun product lines, specifically the KWC Model 1911 vs. the Cybergun Tanfoglio Witness 1911 and the KWC Taurus PT99 vs. the Cybergun GSG 92. In a nutshell, they are all made by KWC and are exactly the same with the exception of some of the licensing and branding that goes on the slides. Cybergun simply contracts KWC to make the guns for them and add some slight different printing. All parts are interchangeable.
I also show you the Silver Finish Blowback Airsoft KWC Desert Eagle and mention again that the licensing on this one is kind of hit and miss depending on what KWC sends us. So when you order one there is an additional surprise waiting for you when you open the box :)
Lastly, I show for the first time a G&G Airsoft product, the G&G Xtreme 45 Blowback that looks an awful lot like the Umarex Colt Special Combat chambered in 4.5mm Steel BB. The main differences are that the Colt Special Combat is a BB gun and the Xtreme 45 is an Airsoft gun. The G&G has blowback where as the Colt Special Combat does not have blowback.
Make sure to checkout my Vimeo video of this product update for even more info!
As with most new items I pickup, I like to share them with everyone. I am checking into some more ROHM blank guns, an RG-59 and RG-88, the RG-59 is a lot like the ROHM RG-56 .22 caliber blank revolver I sell in the Canada Replica Airguns Store but in .380 caliber and the one I show off here is a 5 shot two-tone model. Other than that they use the same frame and mechanical parts throughout.
I also received a black/blued ROHM RG-88 which is kind of like a Walther PPK in design, it field strips the same, has a similar safety setup and even has a similar size and look to it although it is definitely not a replica of a Walther PPK. I am impressed with the overall quality of the ROHM blank guns, material used, fit and finish is very good.
Lastly, I acquired a pre-owned Umarex CP99 CO2 Pellet Pistol from a customer of mine. It is in pretty much in new condition and is one of the Umarex guns I was missing in my collection and have been looking to add. The Umarex CP99 is a pretty good replica of the Walther P99 and uses the standard Umarex metal 8 shot rotary magazines and shares the same CO2 grip fed magazine as the CPSport. The CP99 is German made so it's not one of the lower cost Umarex pistols out there but you do get what you pay for ;)
