In this Vimeo video, I go over a common question I get pertaining to the recoil effect of Airguns and Blank Guns. Many people want to know if Airguns and Blank Guns have similar recoil effects to a Real Guns and if so, how much recoil will you feel from an Airgun or Blank Gun?

The short answer is yes, there is some recoil with both Airguns and Blank Guns since whenever there is a force in one direction there will be a somewhat similar force in the opposite direction creating what we feel as recoil. With Airguns since the force from the CO2 or compressed air is rather small in comparison to that of the gun powder blast from a Real Guns or even a Blank Gun, the recoil is very slight. Blank Guns have similar gun powder charges to a Real Gun and so the recoil is more noticeable but unlike a Real Gun, a Blank Gun does not really push against a sizable object like a bullet, a Blank Gun only pushes against the air in front of the barrel which has very limited resistance and so there will be much less felt recoil from a Blank Gun than the recoil from a Real Gun pushing on a heavy grain bullet.

With semi auto Guns like Blowback Pellet and BB Guns and semi auto Blank Guns, there is also the momentum and mass of the slide to consider as it moves backwards and forwards which also gives the effect of recoil and in the case of an Airgun accounts for most of the recoil felt by the shooter.

Watch my Vimeo video on this subject where I go into much more detail and explain the effect of recoil when shooting Airguns and Blank Guns:

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

Some "not so new" CO2 Blowback 4.5mm Steel BB Pistols from Umarex, but still popular Replica BB guns that have received a lot of attention and to be honest have to date not had a real "proper" Field Test. So why not put the Umarex SA177 and Umarex HPP side by side for yet another installment of Head to Head Shootouts!

Right off the bat I have to say that one of these very fine Blowback Air Pistols has been retired by Umarex. Word on the street is that some suits from a company that sell real steel semi auto pistols that kind of share a similarity to the Umarex SA177 may have applied some pressure to Umarex and somehow the mold got broken and guess what... No more Umarex SA177's :(

On a positive note, you can still get the Umarex HPP which in my opinion was always a better shooter with a much heavier and snappier blowback along with a very smooth trigger. And yes we have it the HPP for sale in our Canada and US Replica Airguns Stores.

Getting back to this Field Test Head to Head Shootout for the Umarex SA177 and HPP CO2 Blowback 4.5mm Steel BB Pistols. I tested them both out on the Chronograph shooting 5 rounds in each gun using a brand new 12 gram CO2 in combination with 5.1 grain Umarex Zinc Coated Steel BB's. The SA177 average a bit higher at 395 fps while the HPP came in just a hair lower at a respectable 372 fps average.

In terms of accuracy from 30 feet out using a semi rested position (sand bag in the front, standing in the back), Both guns wanted to shoot just a bit to the left and they both had a definite internal tighter group that was about 1.5 inches with some strays that came outside opening the groups up to around 3 inches or so. Both BB Air Pistols worked flawlessly with no problems, again the Umarex HPP for me was more enjoyable to shoot with it's heavy blowback and lighter trigger over the SA177. You can also expect to get around 100 or even more shots out of a single CO2 cartridge.

Make sure to checkout my initial Table Top comparison video for these two Umarex Blowback BB Pistols, it goes back a few years for sure :)

Buy Umarex HPP gun in Canada   -   Buy Umarex HPP in the US

I was waiting for a magazine for my ASG STI Duty One 1911 to show up so I could finally do this "Head to Head" Field Test Shooting Review Video for the ASG STI Duty One versus the ASG CZ 75 P-07 Duty versus the ASG Bersa BP9cc. All of which are Blowback CO2 4.5mm Steel BB pistols.

This Shooting Field Test went fairly well and all guns performed as expected, I did have one slide lock back on a loaded magazine with my ASG STI Duty One 1911 and one failure to lock back on the last shot with my ASG Bersa BP9cc, but it did eventually lock back.

During the Chronograph 5 shot per pistol test I got fairly similar fps from all three guns with the STI Duty One getting the highest of 372 average fps, the Bersa BP9cc getting runner up with 353 average fps and the CZ 75 P-07 Duty trailing the field just a bit with a 346 average fps.

During the target portion of this Field Test Shooting Review from 30 feet back in a semi rested position, again the pistols shot fairly similarly with all of them getting pretty close to 2-3 inch groupings. I did have a double shot right after my slide lock back on the STI Duty One as I pressed the trigger twice, once when the slide was locked back and again when I released it, this chambered two BB's into the barrel making the gun shoot a bit low for that double shot. With that negative one against the STI Duty One 1911, I did however find it the most pleasing to shoot! It had the best blowback action and the smoothest trigger, plus I just like holding and sighting in 1911's :)

The CZ 75 P-07 had the next hardest blowback with the Bersa BP9cc coming in second in the trigger department. All of these CO2 blowback BB pistols should get somewhere around 100+ shots pre CO2 if you take your time a bit between reloading magazines.

Buy ASG BB Pistol From the Canada Store - Buy ASG BB Pistols from the US Store

I finally got some brand new Umarex pistols to share with you in this Vimeo video, all three of these CO2 4.5mm Steel BB pistols have blowback and use full size drop out magazines. They also all share single action only operation.

The Umarex Makarov Ultra (Legends Series) is an all metal pistol with very heavy blowback and a long but fairly smooth and medium pull single action trigger. Everything works just like the real steel version including the slide catch/release and safety. It is also fully field strip-able.

The Beretta 84 FS (Cheetah) also has a decent blowback feel but the trigger was a bit heavier on this model, perhaps the trigger will break in a bit over time? Still a really great full metal and fully licensed CO2 Blowback BB shooter with awesome weight to it. The Beretta 84 FS is fully field strip-able and has a working slide catch/release and safety.

Lastly I show you the Umarex Mauser C96 Boomhandle (Legends Series), although much of the external materials are plastic, there is lots of metal throughout like the barrel, bolt, rear sight, hammer, safety, trigger and most of the drop out magazine, giving this pistol a good overall weight to it. The blowback is super fast and crisp with a nice short and light single action trigger making rapid fire very quick.

Umarex Makarov Ultra CO2 Blowback 4.5mm BB Pistol 

• Full metal

• Blowback operation

• 4.5mm Steel BB

• 12 Gram CO2

• Single action only trigger

• Fixed sights

• 3.5 inch smooth bore barrel

• 1.4 pounds

• 16-17 round magazine

• 350 fps

Umarex Beretta Mod. 84 FS CO2 Blowback 4.5mm BB Pistol

• Full metal

• Blowback operation

• 4.5mm Steel BB

• 12 Gram CO2

• Single action only trigger

• Fixed sights

• 3.6 inch smooth bore barrel

• 1.5 pounds

• 16-17 round magazine

• 360 fps

Umarex C96 Mauser CO2 Blowback 4.5mm BB Pistol

• Metal & plastic

• Blowback operation

• 4.5mm Steel BB

• 12 Gram CO2

• Single action only trigger

• Adjustable rear sight

• 5.5 inch smooth bore barrel

• 1.8 pounds

• 19 round magazine

• 380 fps

Buy Umarex BB pistols in Canada - Buy Umarex BB pistols in the US

In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.

All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.

Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.

CO2 Airguns:

• CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.

• CO2 Airguns generally store enough CO2 for multiple shots per cartridge.

• CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.

• Some CO2 guns can also use pressurized air tanks in place of CO2.

Spring Piston Airguns:

• Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.

• Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.

• Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.

• Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.

• Spring Airguns can use either a mechanical spring or a gas spring.

Pump Airguns:

• Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.

• Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.

• Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun. 

Misc Airguns:

• Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.

• Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.

Pros:

CO2 Airguns:

• CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.

• CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.

• CO2 Airguns allow for true semi auto shooting ability. 

Spring Piston Airguns:

• Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.

• Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns. 

Pump Airguns:

• Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.

• Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

• Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.

Cons:

CO2 Airguns:

• CO2 Airguns require the purchase and use of CO2 or they simple do not work.

• CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.

• CO2 Airguns have a maximum set amount of power output.

Spring Piston Airguns:

• Spring Airguns require the pre-cocking of the spring for each shot.

• Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.

• Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions. 

Pump Airguns:

• Pump Airguns require pre-pumping to pressurize the air chamber for each shot.

• Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.

• Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.

In this Comparison video I go through the benefits and shortcomings of both Blowback and Non-Blowback Airguns. I focus mainly on Airguns but there is a definite crossover with Airsoft guns.

Here are some basic statements that best describe both Blowback and Non-Blowback Airguns.

Blowback Airguns:

• Blowback Airguns usually have a movable slide that moves back and forth with each shot.

• Sometimes the blowback operation is internal (Internal bolt) so there may not be an external moveable slide.

• Some CO2 is used to move the slide rearwards in a Blowback Airgun.

• The Blowback motion of the slide with some blowback airguns can also cock the hammer or internal striker allowing for true single action trigger pull. But not always!

• Some Blowback airguns have the potential for full auto capabilities since they can have a true semi auto action.

• There is some noticeable recoil from the Blowback action simulating the recoil of a real gun.

Non-Blowback Airguns:

• Non-Blowback Airguns can have fixed or movable slides but they will not cycle back and forth with each shot.

• Non-Blowback Airguns tend to have less working parts since no Blowback valves are required or even a moveable slide.

• There are some Blowback and Non-Blowback Airguns that field strip similarly to their real steel counterparts but this is most commonly found in Blowback Airguns.

• Non-Blowback Airguns require the shooter to cock the hammer for single action shooting or use a double action trigger pull for semi auto like performance.

Pros:

Blowback Airguns:

• Blowback Action causes a noticeable recoil which makes the airgun feel more realistic.

• Blowback Airguns in some cases have true semi auto action with true single action triggers which mimic the authenticity of the real steel versions of the guns they replicate much better making them better training tools.

• Having some recoil makes blowback Airguns potentially better training tools.

• Blowback Airguns look really cool when shooting them  and are great action prop guns.

Non-Blowback Airguns:

• Non-Blowback Airguns tend to have less working parts so less to go wrong and more reliability.

• Non-Blowback Airguns can be more accurate since the recoil from the blowback is not a factor.

• Non-Blowback Airguns have more potential power and more shots per CO2 since no CO2 is robbed for the blowback operation.

Cons:

Blowback Airguns:

• Blowback operation can rob some of the power and will also rob how many shots you get from the Airgun.

• Blowback Airguns are effected even more by cold weather and the cool down effect.

• The recoil from Blowback Airguns can effect accuracy for some shooters.

Non-Blowback Airguns:

• Non-Blowback airguns are generally double action when shooting semi auto and so the trigger pull will be longer and heavier.

• Non-Blowback Airguns do not replicate the recoil action of a real gun.

• Non-Blowback Airguns do not look as cool to shoot and are not as good of an action prop gun.

It seems like most Replica Airguns collectors are looking for their Replica Airguns to be made out of metal. I even get people complaining about the frames of their airguns being made out plastic (polymer), when in fact the real steel version the gun is designed to replicate also has a plastic or polymer frame.

Most modern real guns are made as light weight and compact as possible, utilizing high grade plastics (polymer) and light weight metals. Of course they use high grade hardened steel in areas where the gun receives the most pressure and continuous wear and tear.

In the real steel gun world, lighter is often better since carrying around a 3 pound pistol all day can be uncomfortable. On the other hand in the Replica Gun world it can be the other way around as replica airgun collectors want that heavy clanky gun that feels solid and real in the hand.

This begs the question - Do Airguns really need to be made out of metal? For strength reason generally not since high pressure is not a factor even in blank guns as there is no bullet holding the pressure in the barrel and when talking about an Airgun or Airsoft Gun, there is even less pressure on the internal parts. For this reason most companies use low grade metals that have a higher content of zinc, often called pot metal. Even though it looks and feels like gun steel it is not nearly as strong and will scratch and break much easier and not be able to handle high pressure. So even though you may think metal is a better option for an Airgun, the reality is that plastic can sometimes be a better option, at least in terms of durability.

What are the benefits to Plastic components:

• Lighter weight.

• More flexible, can take a bit of a beating without breaking.

• Does not show scratches or dents as much as metal. 

What are the benefited to Metal components:

• Gives the gun a more realistic weight, feel & sound.

• In some situations will wear better than plastic. 

What are the cons to Plastic components:

• Can be less realistic in weight, feel and sound.

• Can wear quicker than metal parts in some situations.

What are the cons to Metal components:

• Shows scratches and wear more.

• Lower quality metals can break or crack fairly easily. 

What do I prefer?

• I prefer realism so I like to have metal parts where they would be in the real version of the same gun.

• I like my Replica Guns to have a similar weight and feel as their real steel counterparts.

• I like higher quality metals to be used in the mechanical parts like: (pins, triggers, hammers, barrels, screws, springs, catches…)

• I don't mind the use of plastic when it is high quality plastic and again when used in a similar manor to the real steel version of the gun.

Watch my Vimeo video on What is Better - Plastic or Metal Replica Airguns?

I finally answer the question... Which Airgun is the Best? There has to be a best airgun out there right? So let's cut to the chase and stop waisting everyones time and money buying the third Best Airgun or even the second best Airgun! Why would you even want anything other than the very best Airgun available to mankind!

I really hope you weren't one of the gullible ones that actually bought something other than the Best Airgun, well I guess you're going to have to watch my YouTube video to find out which Airgun is the Best Airgun of all time...

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.

Type: Airsoft AR M16 Styled Rifle.

Manufacturer:G&G.

Model:CM16 Carbine GBB.

Materials: Metal and plastic/fiber construction.

Weight: 5 pounds.

Barrel: 10 inches, metal non-rifled.

Propulsion: GBB

Action: Semi & full auto blowback.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 30+ round magazine.

FPS: 370+.

I could pretty much copy and paste my review of my G&G CM16 Raider GBB since both of these guns are pretty much the same Airsoft Rifle with different finishings. Instead I will place a link to my G&G CM16 RaiderVersion 2 GBB AR Airsoft Rifle Review and insert some nice photos of the  G&G CM16 Carbine version for you to admire :)

Buy the G&G CM16 Raider GBB Airsoft Rifle in Canada - Buy G&G Airsoft Rifles in the US

This is take 2 of my Modification to my F1 Chrony Chronograph. The purpose of this modification is to improve the low light FPS readings. In my first attempt I used LED Puck Lights but they where the kind that used flat panel LED's and they only had 4 panels per LED Puck which made each LED panel kind of bright. I did get OK with my first mod using LED Puck Lights but not as good as I would like to see.

So here we are with take 2 of F1 Chrony Chronograph LED Puck Light modification and this time around I am using standard bulb styled LED lights and to improve my chances of this working I went with and LED Puck that contained 24 LED bulb lights per puck, this way each light on it's own is a bit dimmer which I feel will give a more diffused lighting effect and hopeful consistent fps readings.

By the way I got these LED Puck Lights at my local dollar store for $2.50 each so not a very expensive modification, especially if they work.

Well... Watch the video and see how they perform...

This video was made to show you the results I got by mounting LED puck lights to the top of my F1 Chrony Chronograph defuser panel in order to improve the low light Feet Per Second readings when using 4.5mm Steel BB's.

I have been struggling with my F1 Chrony Chronograph during the fall and winter months as tit becomes overcast and dark where I live. There have been days where I have gone out to shoot my field test shooting video and not been able to get any Chronograph fps results which is very frustrating because much time and effort goes into the planning setup of each video.

I was given advice from several of my viewers to mount an LED puck style light on the back side of my Chronograph defuser panel and that this helps the Chronograph to read much better in low light situations.

I bought a multipack of the LED puck lights from my local Costco but they did not work as well as I expected them to as they had a panel style of LED rather than the bulb shaped LED which I think may diffuse the light a bit more. My next experiments will be done using LED Puck lights but with the bulb styled LED.

You can watch my video to see how my first attempt using an LED Puck light with my F1 Chrony Chronograph worked out.

Moving on to the head to head comparison of the Tanfoglio Gold Custom versus the Sig Sauer X-Five Sight Rail (Open version). Again like my previous video of the KWC Model M1911 Tac A1 versus the Cybergun-KWC GSG 92-M92, these two Air Pistols feature full size drop out metal magazines that hold the CO2 and 4.5mm steel BB's, along with full blowback with working slide catches, safeties and magazine releases. Both are field Strippable and both have the addition of sight rails with red dot sights for quick target acquisition.

I did not find either sight rail pistol to be all that much more accurate than similar open sight pistols like the KWC Model M1911 Tac A1 and Cybergun-KWC GSG 92-M92, but I did find that target acquisition was much quicker and even when I accidentally double tapped the trigger, the second round was right on target.

In this field test comparison I shoot both guns through my Chronograph to see what kind of feet per second performance each one shoots, I also take them back 30 feet and shoot 10 rounds on a paper target using a semi rested position for true accuracy results.

Watch my Field Test Head to Head Shootout for the Tanfoglio Gold Custom versus the Sig Sauer X-Five Sight Rail:

Buy BB Pistols in Canada 
Buy BB Pistols in the US

Buy KWC Sig P226 X-Five in Canada
Buy KWC Sig P226 X-Five in the US

Here is the third video in a series of Head to Head Air Pistol Shootouts. In this video place the KWC Model M1911 Tac A1 head to head versus the Cybergun-KWC GSG 92-M92.

Both CO2 4.5mm Replica Air Pistols feature full size drop out metal magazines that hold the CO2 and 4.5mm steel BB's. These super realistic BB guns also have full blowback with working slide catches, safeties and magazine releases and they can both be field stripped juts like the real steel versions.

In this field test comparison I shoot both guns through my Chronograph to see what kind of feet per second performance each one shoots, I also take them back 30 feet and shoot 10 rounds on a paper target using a semi rested position for true accuracy results.

Watch my Field Test Head to Head Shootout for the KWC Model M1911 Tac A1 vs Cybergun-KWC GSG 92-M92:

Buy the Swiss Arms P92 in Canada

Buy the Swiss Arms P92 in the US

Buy the KWC Model M1911 A1 Tac Blowback 4.5mm BB Pistol in Canada

Buy the KWC Model M1911 A1 Tac Blowback 4.5mm BB Pistol in the US

I get many question over on my Vimeo Channel, lots of times people asking me which gun is better and in most cases it really comes down to personal preference. But in some situations the comparisons are really close and to be honest it's even hard for me to decide which gun I think is better.

I get asked which one has higher fps, or is more accurate, or has harder blowback recoil... the list goes on. Without actually taking both gun outside and doing a head to head test using the same exact situations, I really can not honestly tell you! So that's exactly what I am going to do. Take some of the most commonly asked about gun comparisons and have a showdown.

Over the next while I will be making a total of five separate videos where I compare the following CO2 BB pistols head to head:

• The Tanfoglio Gold Custom versus the Sig Sauer P226 X-Five Sight Rail Version

• The KWC Model M1911 Tac A1 versus the Cybergun/KWC GSG 92/M92

• The ASG Dan Wesson 8 inch Revolver versus the Umarex Smith & Wesson 327 TRR8

• The ASG CZ 75 P-07 Duty versus the ASG Bersa BP9CC versus the ASG STI Duty One 1911

• The Gamo PT-85 versus the Umarex Beretta PX4 Storm

Make sure to come back and check out these upcoming head to head field test shooting videos!