View fullsize

In this Field Test Shooting Review I’m taking a look at the Umarex T4E TC68 .68 caliber paintball / less-lethal marker to see how it performs in terms of velocity, accuracy, and overall shooting experience.

I have already done a Table Top Review covering the specifications, features, and overall purpose of the TC68, so make sure to check that video out if you want the full breakdown of the gun itself. This field test review is focused strictly on real-world performance.

For this test the TC68 has been de-restricted, meaning the adjustment screw has been modified slightly so it can reach its full potential. Even with this adjustment it should still remain legally compliant here in Canada, since the velocity will remain under the 500 fps threshold.

For ammunition I used .68 caliber nylon rounds:

• Black rounds: approximately 2.8 grams

• Yellow rounds: approximately 2.6 grams

The TC68 in this test is powered using dual 12-gram CO2 cartridges, rather than the larger 88-gram CO2 cylinder, which will affect both shot consistency and total shot count.

View fullsize

Velocity Testing

For the velocity portion of the test I fired several shots through my chronograph.

Chronograph readings were somewhat tricky to capture at first, but once everything started working correctly I was able to record several shots.

Example readings included:

• 476 fps

• 463 fps

• 453 fps

• 445 fps

The velocity dropped slightly during the test, which is expected when using dual 12-gram CO2 cartridges, as they cool down fairly quickly during rapid shooting.

The slightly heavier 2.8-gram black rounds were also used for some of the shots, which can contribute to minor changes in velocity compared to the lighter 2.6-gram rounds.

Even with that drop, performance was still strong and suggests the TC68 could likely reach high-400 fps velocities with a fresh CO2 setup or an 88-gram CO2 cylinder, which provides much greater gas capacity and improved consistency.

View fullsize

Accuracy Testing

For the accuracy portion of the test I set up a paper target down range and loaded roughly 20 rounds into the magazine.

The first test consisted of 10 shots in semi-automatic mode using the heavier black nylon rounds. A red-dot optic was installed on the TC68 for aiming, though it had not been sighted in or adjusted beforehand.

Results were quite respectable for a marker shooting heavy .68 caliber rounds.

• Overall grouping was approximately 4 inches

• Most shots landed within a 2.5–3 inch cluster

• One shot landed slightly low outside the main group

Considering the optic was not adjusted and this was essentially a right-out-of-the-box test, the accuracy was quite good.

Full-Auto Shooting Test

After the semi-auto accuracy test I attempted a full-auto burst test, but quickly discovered the CO2 had been depleted.

After installing fresh CO2 cartridges, the full-auto test was repeated with approximately 20 rounds loaded.

The TC68 does not have an extremely fast rate of fire, but it still delivers a solid stream of rounds when the trigger is held down.

View fullsize

During full-auto fire:

• The gun remained fairly controllable

• Rate of fire was moderate but effective

• CO2 cooling became noticeable during sustained bursts

A fresh target confirmed that the TC68 was still accurate enough for defensive-style shooting, keeping the majority of rounds within the main target area even during burst fire.

Power and Energy

Using approximately 2.8-gram nylon rounds traveling around 475 fps, the TC68 is producing significantly more energy than its factory-rated 16-joule output. Closer to 30 joules!

The modification performed simply allows the power adjustment screw to reach its full depth, allowing the marker to operate closer to its maximum potential.

While exact energy figures will depend on projectile weight and velocity, the TC68 in this configuration appears capable of producing considerably higher energy levels than stock, while still remaining under the 500 fps legal limit in Canada.

Shooting Impressions

Overall the Umarex T4E TC68 proved to be a solid and reliable platform during testing.

Some observations from the field test:

What I liked

• Strong velocity potential

• Good accuracy for a .68 caliber marker

• Full-auto capability for rapid follow-up shots

• Compatible with multiple CO2 power options

Things to consider

• Dual 12-gram CO2 cartridges cool down quickly

• Larger 88-gram CO2 cylinders will provide better consistency

• The gun includes multiple safety mechanisms that require familiarity

The TC68 includes three levels of safety, which helps prevent accidental discharge but does require some practice to become comfortable with the controls.

View fullsize

Final Thoughts

The Umarex T4E TC68 performed well in this field test.

Velocity was strong, accuracy was respectable for a .68 caliber marker, and the full-auto capability adds an interesting dimension to the platform.

With proper setup and a fresh CO2 source, the TC68 has the potential to deliver high-energy shots while still remaining within Canadian legal limits.

Overall it’s a very capable paintball / less-lethal marker and definitely an interesting option for those looking for a high-power .68 caliber platform.

• Buy the Umarex T4E TC 68 Less Lethal Paintball Rifle in Canada

• Buy Paintball Guns in the US

Michael here from Replica Airguns with an important public announcement, especially for those of you who mainly follow us on Vimeo or Rumble.

If you are watching this on YouTube, then you probably already know the news, we are finally back on YouTube. However, a lot of our long-time viewers may not be aware of this yet, so if you have the opportunity to help spread the word, it would really mean a lot to us.

What Happened to Our Original YouTube Channel

Several years ago our original YouTube channel was suddenly terminated due to what YouTube described as a “counterfeit claim.” Unfortunately, we were never given any clear explanation about what specific video or product triggered the action.

At the time, the Replica Airguns channel had been built over many years and included over 1,000 videos, millions of views, and hundreds of thousands of subscribers. Losing the channel meant losing our entire YouTube audience overnight.

To this day, we still do not know exactly what product or video led to the termination. Replica Airguns does not sell counterfeit products. All of the airguns and replicas we review and sell come from legitimate manufacturers such as:

• Umarex

• ASG

• Crosman

• SIG Sauer

• and other major licensed manufacturers

These companies produce officially licensed replica versions of real firearms, which is why they look authentic. The difference is that they shoot BBs, pellets, airsoft, or paintball rounds, not real ammunition.

Unfortunately, once the termination occurred, there was no real way to speak with a person or properly dispute the decision. Like many others at the time in the airgun community, we were caught up in a period when gun-related channels were facing heavy restrictions or removals.

A Fresh Start on YouTube

The good news is that we are rebuilding.

Over the last couple of months I have been gradually uploading our videos back to YouTube. The process is a bit slow since it requires moving videos over individually, but it is working and the library is growing quickly.

So far:

• 800+ videos uploaded

• 1,300+ total videos planned

• 130+ new subscribers

• 10,000+ views and growing

Considering we are essentially starting from scratch again, this is encouraging progress.

Why Uploading Takes Time

Some viewers have asked why all the videos are not already up.

The main reason is that the transfer process from Vimeo to YouTube still requires a bit of manual work. Each video needs to be shared individually, which takes several clicks and some time for page refreshes and processing. Moving around 50 videos can take close to an hour or more, so it is something I do gradually every few days.

The good news is that once a video is sent to YouTube, the rest of the upload and processing happens automatically.

What to Expect

While the archive videos are being uploaded, new videos can sometimes get buried under the older uploads. Once the full library is back online, I will be reorganizing everything into playlists, including:

• Tabletop Reviews

• Field Test Shooting Videos

• Pellet Gun Reviews

• Airsoft Reviews

• Paintball Markers

• Other replica airgun categories

This will make it much easier to find specific content again.

Help Us Rebuild the Channel

If you have been following Replica Airguns for a long time, you know how much work went into building the original channel. Rebuilding it will take time, but with your help we can get the community back together again.

If you can, please help by:

• Subscribing to the new YouTube channel

• Sharing the channel with other airgun enthusiasts

• Letting people know Replica Airguns is back

You can find us on YouTube under:

RA Returns - @RAReturns

The name simply stands for Replica Airguns Returns.

Follow Replica Airguns

You can also find Replica Airguns here:

• Website & Blog: ReplicaAirguns.com

• Canada Store: ReplicaAirguns.ca

• US Store: ReplicaAirguns.us

We also post updates on Facebook, Twitter/X, and Instagram.

Thank you to everyone who has supported Replica Airguns over the years. We are excited to rebuild the YouTube channel and continue producing the airgun reviews, field tests, and content that this community has always enjoyed.

Stay tuned - there is a lot more content coming soon.

In this Table Top Review we’re taking a close look at the Sig Sauer P229 CO2 Blowback Pellet Pistol. This is the tabletop portion only, no shooting in this review as my Field Test Shooting Video will follow later on.

If you’re familiar with the Sig Sauer ASP P226 platform, the P229 version is the same general system in a more compact package, with one major upgrade: it’s optics-ready!

View fullsize

Specifications

• Manufacturer: SIG SAUER

• Power Source: 12g CO2

• Ammunition: .177 pellets (also supports steel BBs)

• Action: Semi-auto, blowback

• Trigger: DA/SA (double action / single action)

• Magazine: 16 rounds (twin 8-shot rotary clips, loaded on both ends)

• Barrel: Rifled inner barrel

• Sights: White dot sights

• Safety: Manual safety lever with de-cocker function

• Claimed Velocity: up to ~380 fps (real-world varies with temperature and cadence)

• Shots per CO2: roughly 50–60 (varies with temperature/cadence)

• Weight: 35.2 oz / 1.0 kg (2.2 lb)

• Overall Length: 7.7 in (P229)

• Optics: optics-ready slide / SIG AIR reflex-sight mounting provision

• Muzzle threads: M14x1 CCW

View fullsize

In the Box

• P229 CO2 blowback pellet pistol

• Manual

• Sight/plate parts for the SIG AIR reflex mounting setup (for red dot use)

P226 vs P229 - What’s Different?

These two share the same general operating system (CO2 blowback, DA/SA, rotary-mag that works with pellets/BBs), but the P229 version changes a few important things:

View fullsize

Key Differences

• Size: P229 is shorter (7.7 in) vs P226 (8.25 in).

• Weight: P229 is lighter (35.2 oz / 2.2 lb) vs P226 (~39.1 oz).

• Optics: P229 is optics-ready (SIG AIR reflex mounting provision); P226 platform is typically not.

• Muzzle threads: P229 uses M14x1 CCW (P226 commonly uses a different thread direction/size).

Bottom line: if you liked how the P226 handled and performed, the P229 should feel very familiar, just more compact, with the bonus of being set up for a dot.

Walk-Around & Handling

The P229 has that classic SIG profile and a very “real pistol” feel in the hand, helped by the mostly-metal build and full weight.

View fullsize

Notable features and controls:

• DA/SA trigger system: long/heavier first pull in double-action, then lighter single-action after the slide cycles.

• Safety + de-cocker lever: functions like the real-steel concept — you can decock the hammer and run it DA/SA.

• Accessory rail: for a light/laser (training-style setup).

• Optics-ready slide: set up to accept the SIG AIR reflex-style mounting system (sight sold separately).

CO2 System and Magazine Notes

One of the standout features on this platform is SIG’s cam-lever, tool-less CO2 loading system, designed to make cartridge swaps quick and easy.

The magazine is a 16-shot design using twin 8-shot rotary clips. Practical tip: make sure pellets are seated properly in the rotary clip so they don’t hang up during cycling.

View fullsize

Pros

• Mostly metal build with realistic weight and solid feel

• Compact P229 size (shorter than the P226)

• DA/SA trigger + functional safety/de-cocker system

• Blowback action for realism/training value

• Rifled inner barrel (pellet accuracy potential)

• Tool-less cam-lever CO2 loading system

• Optics-ready slide (big upgrade over older-style setups)

• Accessory rail for light/laser

Cons

• Fixed/non-adjustable sights

• CO2 performance is temperature + cadence sensitive (rapid fire cools the system and drops power)

• No last-round hold-open on this style of rotary-mag system

• Rotary clips require good pellet seating to avoid occasional feeding issues

View fullsize

Final Thoughts

The Sig Sauer P229 blowback pellet pistol is a very “SIG-like” training/plinking platform: realistic controls, DA/SA operation, snappy blowback, and a compact duty-pistol footprint. The biggest tabletop takeaway is the optics-ready slide, which makes this version feel more modern than older CO2 pellet pistol designs.

Field test shooting (chronograph + accuracy) will follow in the next video.

Available in our Canada Replica Airguns Store. Also check out:

• Buy the Sig Sauer P229 in Canada

• Buy the Sig Sauer P226 in the US

View fullsize

Type: .68 Cal Paintball / Training Marker Rifle /Less Lethal
Manufacturer: Umarex (T4E / Training for Engagement)
Model: T4E TC68
Made In: Taiwan
Materials: Polymer exterior with internal metal components (metal flash hider + various metal controls)
Weight: 2.5 kg (5.52 lb)
Overall Length: 84 cm (33")
Barrel: Approx. 31 cm (12") smoothbore (.68 cal)
Power Source: 2x12g CO2 (in-stock dual system), 88g CO2, or HPA (via included adapter)
Action: Semi-auto and full-auto
Ammo Type: .68 Cal paintballs, rubber balls (including heavier core types), powder/dust/chalk balls, glass balls, pepper balls (where legal), and First Strike–style shaped rounds (magazine-fed)
Ammo Capacity: 20-round spring-assisted magazine (plus hopper-fed option with included adapter)
Claimed Velocity Range: 240–480 fps (adjustable; depends heavily on ammo weight and air source)
Energy (Context): Marketed around 16J “out of the box,” with higher output possible via the built-in adjustment system (jurisdiction-dependent and often tamper-restricted)

View fullsize

Trigger Pull
The TC68 uses a semi-auto style trigger that feels closer to a single-action pull (it needs to work this way to support full-auto). The break is straightforward and predictable, and it suits the “training marker / utility” role well.

Accuracy

This table top review is focused on features, build, and usability. Accuracy testing and chronograph results are better handled in a field test once ammo weight is confirmed (rubber vs. paintball vs. hard plastic rounds will all change results). Initial “gut feel” shooting suggests the factory setting is already pushing hard for a training marker, with performance feeling consistent with the advertised 16J class.

Build Quality

The TC68 is largely polymer on the outside, but it doesn’t feel like a toy. The weight is substantial, controls feel solid, and the overall package is clearly built for training and repeated handling. You’re getting a robust platform designed to run multiple air sources and a wide range of .68 caliber projectiles without needing a bunch of aftermarket parts just to get started.

Realism / Ergonomics / Controls

Visually and ergonomically the TC68 leans into an AR-style layout:

• AR-style grip geometry (and AR-compatible grip fitment style)

• Full-length Picatinny top rail

• M-LOK on the handguard (sides and bottom) for lights, foregrips, etc.

• Ambidextrous selector (Safe / Semi / Full)

• Ambidextrous magazine release

It does not have real-steel operating controls like a charging handle or functional bolt/dust cover, this is a marker, not a firearm replica mechanism, but from a distance it reads like a modern sporting rifle pattern, which matters for training applications and general “presence.”

Safety systems are layered:

1. A “quick pierce / activation” setup (pressurizes the marker only when you choose)

2. A cross-bolt style safety that controls readiness to fire and can also depressurize when switched back (you’ll hear it vent)

3. Standard safe selector switch position

View fullsize

Air Source Flexibility (CO2 + HPA) and Included Hardware

This is one of the biggest selling points: it ships with a lot of the “bits and pieces” that usually cost extra.

You can run:

• Dual 12g CO2 (the configuration shown in the review)

• 88g CO2 (full-length stock configuration)

• HPA via included adapter (plus an alternate stock option that works well with compact tanks)

The included quick-pierce style setup is practical: you can stage the marker with CO2 installed without continuously bleeding gas, then activate it only when needed.

View fullsize

Feeding Options: Magazine-Fed or Hopper-Fed

Out of the box you get:

• A 20-round spring-assisted magazine designed to load easily (the spring can be held back during loading, then feeds when inserted)

• A hopper adapter system (hopper not included, but the adapter is), letting you run higher-capacity paintball-style feeding for volume use, especially relevant if you pair HPA + full auto

The magazine also supports First Strike–style shaped rounds (magazine-fed only), expanding the use-case options for training and scenario work.

Sights / Optics

No sights are included, no irons, no basics, nothing. That’s the odd omission on an otherwise “complete” kit. Plan on adding:

• a red dot (often easiest), and/or

• irons that sit higher, or a riser setup, depending on your preferred cheek weld and optic height.

View fullsize

Pros

• Multiple air source support (2x12g CO2, 88g CO2, or HPA via included adapters/stocks)

• Quick-pierce / staged-gas concept is practical for readiness without constant leaking

• Semi-auto and full-auto capability

• Adjustable power/velocity range to suit different training and ammo types

• Magazine-fed or hopper-fed flexibility (adapter included)

• Accepts First Strike–style shaped rounds (magazine)

• AR-style ergonomics and lots of accessory mounting (Picatinny + M-LOK)

• Strong “presence” and serious performance feel for a .68 platform

• In Canada especially, it fills a niche many users are actively looking for (training/marker/home safety versatility)

Cons

• Pricey in Canada (around the ~$600 CAD range at the time of the review)

• No sights included (you must budget for at least basic aiming equipment)

• Maximum performance potential may be restricted by factory tamper measures and local rules (and you should not assume higher settings are legal where you live)

View fullsize

Comments

If you want a .68 caliber platform that can legitimately be configured for multiple roles, paintball, training, scenario use, home safety use, the Umarex T4E TC68 stands out because it’s versatile right out of the box. The “complete kit” nature (CO2/HPA readiness + mag and hopper options) is rare at this price point.

The Umarex T4E TC68 is in probably one of the most powerful “Rubber Ball”Airguns you can get here in Canada right now with the ability to even turn it up a notch (at your own discretion). With Canadian legal gun owners losing their rights to own regulated Firearms more and more each day, being able to acquire something that is not regulated may be the best option for non-Firearms Licensed holders and Firearms Licensed holders.

Field test follow-up (chronograph + practical shooting) will matter a lot with this one, because performance varies dramatically with projectile type and weight. That’s where it will be most interesting to quantify real fps and estimated energy across a couple common round types.

• Buy the Umarex T4E TC 68 Less Lethal Paintball Rifle in Canada

• Buy Airguns in the US

It’s been a little while since I’ve done an unboxing, so we’ll call this the February 2026 Mystery Box Unboxing Video.

First up: SHOT Show is officially wrapped on my end, interviews, teaser, the whole run. There should be a playlist available so you can binge everything in one place. Now that the heavy editing grind is done, I’m getting back into regular reviews, unboxings, tabletop breakdowns, and full field tests.

Also: we’re back on YouTube and I’m uploading like crazy. I’m moving the library over from Vimeo one-by-one (lots of clicks, lots of time). We’ve got roughly 1,300 videos total, and I’m already around 500 videos in, so if you’re hunting for something specific, use playlists and search because new uploads can get buried fast. If you can, subscribe and share the channel with other Airgun enthusiasts so we can build momentum again.

What was in the box?

View fullsize

1) SIG P229 (.177 Pellet, blowback)

I initially called it a P226, but it’s the P229 (compact). This is a pellet version (not BB), with:

• 16-round rotary stick magazine (8 per side)

• Blowback, semi-auto

• Claimed 380 FPS

• 3.9" barrel, 7.7" overall length

• 2.2 lb, hefty all-metal feel (mag is plastic)

No slide lock-back due to the rotary setup, but it looks great in-hand. Tabletop and field test videos are coming, and I’ll run it on typical lead pellets to see real-world performance.

View fullsize

2) T4E TC68 (.68 cal, CO2/HPA capable)

This is the TC68 trainer that shoots .68 caliber rounds (rubber, powder, paint, pepper ball options depending on what you choose). Specs and highlights:

• Claimed 330 FPS and 16 joules

• 20-round magazine-fed setup

• Supports dual 12g CO2, 88g CO2, and HPA options

• Includes multiple configurations (stocks/adapters) plus a hopper-fed option

I’ll confirm operating modes, setup options, and performance in the upcoming tabletop and field tests.

• Buy the Sig Sauer P229 Pellet Pistol in Canada

• Buy the T4E TC 68 Paintball Rifle in Canada

View fullsize

I stopped by the Blue Line booth and Connor showed me a line of peppered gel deterrent products they’re hoping to bring into Canada as dog-spray style options (with stronger versions available in the U.S., depending on regulations).

The key difference vs typical pepper spray: these use a jet/propulsion system that fires a more directed stream, designed to reduce blowback and improve placement.

JPX2 Gen 2 (2-shot)

• Takes a 2-shot cartridge; each trigger pull fires one shot.

• The cartridge is replaceable after use (Connor emphasized it’s essentially disposable once fired).

• Connor said range is about 20 ft; manufacturer specs cite roughly 5–23 ft depending on conditions.

4-shot option (JPX4-style)

Connor also showed a 4-shot version aimed at law enforcement markets, but they’re hoping it can be available more broadly as well.

Guardian Angel 4 (compact 2-shot)

A small two-shot, pocketable option with a simple safety and clip—intended as a quick, lightweight grab-and-go device.

Connor also mentioned optional laser sight accessories for better aiming, and that all versions are around the same practical range envelope.

If these can be brought in cleanly for Canada, they look like a good fit for a store + review pipeline: JPX2 Gen 2 for the main feature set, JPX4 for the multi-shot crowd, and Guardian Angel 4 for people who want something ultra-compact and simple.

• Buy Replica Airguns in Canada

• Buy Replica Airguns in the US

View fullsize

We stopped by the SABRE booth and spoke with Ashley about their Home Defense Pepper Launcher, specifically a second-generation version that (per Ashley) isn’t released yet. With less-lethal options getting more attention in Canada, I wanted to see what’s new, what specs we’re looking at, and whether it’s something we might be able to bring in for reviews and potential store availability.

What’s new with the Gen 2 (as described in the interview)

• “Quick Pierce” magazine system: Ashley demonstrated a faster “pierce and go” style setup, hit the control and you’re ready to aim.

• Pressure indicator: After piercing, an indicator pops out; as CO2 is depleted it retracts, giving you a visual cue that pressure is running out.

• CO2 release button: A control to vent the CO2, then remove the magazine.

Core platform details (current production specs for the .68 launcher family)

These are the commonly listed specs for the current .68 caliber SABRE launcher:

• .68 caliber projectiles

• 7-projectile magazine capacity

• Fiber optic sights (front/rear adjustable)

• Stated velocity up to ~350 FPS

• Range: direct impact effectiveness noted around 60 ft (18 m), with projectiles described as breaking/dispersion capability out to 175 ft (53 m)

Ashley also noted SABRE’s projectiles have a heavier payload than some competitors (in her words) to help with “strength” and accuracy.

Magazines, CO2, and shot count (from the interview)

• CO2 goes into the magazine

• 7 projectiles per magazine

• Two magazines per CO2 (so 14 shots)

Canada angle (what matters for importing)

• Ashley noted the current model is around ~20 joules, and said a Canadian version would likely need to be lower(depending on classification/import requirements).

• SABRE’s own online store states they do not ship internationally, including Canada (so any Canada availability would likely be via distribution/import channels rather than direct-to-consumer shipment).

If we can make the Canada piece work, this looks like a strong candidate for a hands-on review, especially because it’s .68 caliber, 7-round, and built around visibility (fiber optics) and ease of use.

• Buy Replica Airguns in Canada

• Buy Replica Airguns in the US

View fullsize

We didn’t catch this one at the Steambow booth, we were out at the SHOT Show indoor range checking out Steambow again, Tyler walked us through their brand-new-for-2026 B08: a magazine-fed .68 caliber ball launcher/crossbow that’s just starting to hit availability.

• New B08 .68 cal “ball launcher” platform (2026): This is a .68 caliber system designed to run .68 spherical projectiles (paint, foam/nylon, and pepper/irritant-type balls were all discussed as compatible options, depending on local rules).

• 8-shot, removable, pre-loadable magazine: The B08 uses a spring-fed 8-round magazine that inserts at the front. Tyler’s demo made it clear you can pre-load multiple mags and keep shooting quickly.

• Simple, repeatable action (easy to learn fast): The manual of arms is very “repeat-and-go”: load the mag, cock it, shoot, then cycle and repeat. Steambow describes the system as their familiar AR-Series quick-tilt/quick-clamp style for fast reloading.

• Ships mild, but can be upgraded for more power: The one I tested was using a 35 lb limb, but it’s built to accept other AR-Series limbs (stronger options sold separately). Tyler specifically said swapping to a much heavier limb can turn it into a high-velocity setup (he referenced up to a 150 lb limb and around 300 fps in his talk).

• Projectile flexibility is the whole point: If you already have .68 cal paintballs or similar at home, that’s the target “ecosystem” this is built around (so long as they’re spherical).

• Important safety + legal reality check: Steambow is very explicit that once you move beyond the “low power + soft balls” envelope, the B08 can become very dangerous, they warn that harder/heavier projectiles (including steel balls) raise risks like severe injury/lethality and ricochets, and that irritant/pepper-type rounds may be legally restricted depending on country.

Tyler’s range demo made the main selling points obvious: magazine speed, easy operation, and a huge range of .68 ball options. If we can get it lined up for Canada, it looks like a very versatile multi use platform, especially for anyone who wants .68 cal fun adn then some, without relying on CO2 or HPA.

View fullsize

We stopped by KWA at SHOT Show 2026 and I caught up with Jonathan to check out one of their hottest new releases for 2026: a licensed Kel-Tec Sub 2000 Replica coming in both Airsoft and BB Airgun variants, with blowback-style fun and that signature folding design.

• EMG x KWA Licensed Kel-Tec Sub 2000 (folding rifle)

  • Variants: Airsoft + Airgun/BB version (already confirmed)

  • Magazine: Uses ATT/ATP GT mags

  • Gas options: Green Gas model shown, with CO2 magazines also planned/available

  • Fire modes: Semi + full auto

  • Controls/rails: Ambidextrous charging handle, M-LOK side rail, Picatinny top + bottom

  • Capacity: ~35 rounds (with potential for slightly higher capacity on the BB version)

  • Timing: Announced at the show; expected late Q2 to early Q3 shipping window

This one looks like a perfect fit for anyone into compact, foldable PCC-style Replicas, especially if you want that “Kel-Tec vibe” with modern rails and full-auto capability.

Watch the Full Interview Video:

View fullsize

I caught up with Mark at the Umarex booth to check out a stack of new releases for 2026, ranging from backyard BB “fun guns,” to a major upgrade for the Thompson, plus a dual-fuel hunting/pest-control PCP concept and some serious less-lethal / training options.

• Storm Line BB Rifle (dual CO2, full auto): A traditional, “tamer-looking” BB rifle that’s anything but tame.

  • Capacity: 400-round main reservoir + 25-round ready magazine

  • Action: Full auto

  • Vibe: Affordable, high-volume backyard fun, while keeping the styling less “tactical,” which could help for markets like Canada.

• Ridge Tech Lever Action (CO2): Lever actions are hot, and this one leans modern while staying simple and budget-friendly.

  • Feed system: 8-round magazine + 120-round reservoir built into the mag

  • Use case: Tin-can plinking and family backyard sessions, “CO2 Red Ryder for adults” energy.

• Thompson M1A1 Drum Magazine Upgrade: The #1 request finally landed: a drum mag for the Thompson.

  • Capacity: 400 BBs

  • How it runs: Wind as needed to keep feeding similar to Airsoft High cap magazines

  • Best part: The drum magazine is planned to be sold separately and should work with the older stick-mag Thompson versions too, so existing owners can upgrade without buying the whole gun again.

• Outpost (25 cal) “Dual Fuel” PCP Concept: One of the most interesting items in the booth, a platform aimed at practical use over pure plinking.

  • Power source: Runs on a nitrogen cartridge or as a traditional PCP-style setup out of the box

  • Caliber: .25 only

  • Design notes: Side lever, folding stock for compact carry, onboard spare-mag storage (prototype shown)

  • Positioning: Built for small game / pest work and “preparedness” minded buyers

  • Canada angle: CO2 use (if supported) could drop velocity, but in this form it sounded like it may currently be on the “too fast for Canada” side, so detuned / CO2-focused variants were discussed as a possibility.

• S68 (68 cal, CO2, ~16J): Compact launcher format with real punch for its size.

  • Power: 12g CO2

  • Magazine: 6-shot standard, extended option mentioned

  • Ballistics talk: Roughly ~360–380 fps with a ~46-grain projectile (as recalled in the interview)

  • Ammo pairing: Steel-core “core defense” style rounds were emphasized for hard impact; pepper options depend heavily on local rules.

• HDX 68 “Shotgun Style” (68 cal): A higher-capacity, higher-energy format.

  • Capacity: 16 rounds

  • Energy: ~36 joules mentioned

  • Use case: Home / business defense in jurisdictions where these products and ammo types are legal.

• HDC 68 (M4/Rifle Style, CO2, adjustable): A configurable platform that can run mag-fed or hopper-fed.

  • Tuning: Adjustable velocity

  • Feeding: Magazine or hopper (round ammo works well; shaped rounds can be used depending on orientation)

  • CO2 options: 88g CO2 or adapters for 12g

  • Why not nitrogen (yet): Too much pressure without regulation, risk of damaging projectiles in the barrel.

• New Ruger-Branded 1911 (CO2 blowback): A dressed-up 1911 variant with extra detail.

  • Notable features: Flared magwell, two-tone finish, extended beavertail, competition-style touches

  • Appeal: A strong trainer option for 1911 fans, great feel, realistic handling, and that classic 1911 cycling character.

• Competition-Style CO2 Pistol (single-shot): A purpose-built target/competition format with modern mounting options.

  • Loading: Single-shot

  • Ergonomics: Competition grip + competition styling

  • Mounting: Built-in rail (no “upgrade it just to mount stuff” hassle)

  • Caliber shown: .177, with the obvious question of a future .22 variant.

Watch the Full Interview Video:

View fullsize

We made it to the Barra Booth here at SHOT Show 2026 and once again I caught up with Jacob to check out what’s new for 2026, lots of “modern western” energy this year, plus some serious PCP development and even a very functional slingshot.

• New “cowboy” premium single-action revolver (PCP cartridge-powered): Unlike most revolvers in this category that run on CO2, this one uses refillable air cartridges (small pressure chambers) filled to ~2000 PSI. You load a pellet into the nose cone, charge multiple cartridges at once using a charging manifold (up to six at a time), then drop the loaded cartridges into the cylinder just like shells.

  • Caliber shown: .22

  • Hand pump fill estimate: roughly ~10 pumps (quick top-offs), with a tip to pump → degas → pump againfor more consistent cartridge pressure.

  • Frame/version: brass frame first, with other versions planned.

  • Positioning: premium / highest-quality cowboy-style item in their lineup; made in Italy.

  • Early price talk: roughly $400–$500 range (with cartridges), but still TBD.

• 1866 CO2 Lever Action – Tactical version (launching this year): Built off their popular CO2-powered 1866 lever action (two CO2 cartridges in the buttstock, shells load into the gun, lever cycles and ejects).

  • Updates: black stock, M-LOK fore-end, larger Picatinny section, and paracord wrap on the lever for comfort.

  • Calibers: .22 is the focus (with .177 also planned/available).

• New slingshot (with internal grip magazine): A compact, foldable slingshot that stores ammo in the grip and feeds by gravity—engineered so it releases one steel shot at a time.

  • Uses flat bands (easy to swap/upgrade for strength/velocity).

  • Sighting: built-in sight plus fiber optic references for left/right-handed use and different ranges.

• Replica-style break barrels (AK + M16 formats): Two new break-barrel rifles styled after an AK and an M16 with non-functional replica controls, but standard break-barrel operation.

  • Sights/optics: adjustable iron sights plus Picatinny rail for optics.

  • Calibers mentioned/planned: .177 / .22 / .25.

• New PCP platform: “300Z” (pre-production prototype in hand): A more serious, modern tactical PCP design with:

  • Folding stock, 1913/Picatinny rear, dual gauges, 2-stage trigger

  • Externally adjustable regulator

  • Ambidextrous side lever (convertible)

  • Rotary magazine (prototype shown in .30 cal, 8 rounds)

  • Power testing target: up to ~80 ft-lb in .30 cal

  • Notes: barrel shroud look—not a suppressor; Canada discussion included licensing/detune possibilities.

• Updated PCP: “270Z” (built off the 250Z, redesigned internals): A redesigned system meant to feel more like a traditional bolt action, with increased plenum volume (machined from a solid block of aluminum) targeting ~20% more power than the 250Z.

  • Features: adjustable cheek rest, M-LOK fore-end

  • Timing: Q2 target for the 270Z; Q3 target for the 300Z.

Jacob also emphasized an ongoing push toward higher workmanship, better materials, and improved performance, and it shows, especially in the new premium western revolver and the next-gen PCP lineup.

Watch the Full Interview Video:

We visited the ASG booth with Bob (his 13th SHOT Show) to check out what’s new for 2026, with several updates aimed at Canadian buyers.

• New budget AR AEG line (April/May target): three versions planned (all-polymer, polymer receiver w/ metal rail, and all-metal). Target pricing is about $150 USD (polymer) and $210–$220 USD (all-metal). Includes battery + charger, plus two springs (one outdoor/Canada-legal and one ~330 FPS), with easy spring swaps. Some models include an ETU.

• GL06 40mm launcher: an older favorite that keeps selling, highlighted for its durable build, long barrel, and long firing pin designed for better reliability with a wider range of shells.

• Canada-focused HPA solution (in development): ASG is working on an HPA setup to help gas blowback models meet Canada’s import threshold (they referenced 367 fps) so more options can be brought into the country.

• Canada version P-10 CO2 (March/April target): updated with a higher-velocity valve aiming around ~380 fps, making it Canada import legal. Comes in black and FDE, full blowback, and includes an optics plate for red dots.

• Blaster BBs refreshed: BB lineup is consolidated into Blaster / Alpha Blaster (premium) / Beta Blaster (budget/field), with options like bio and tracer. US availability is expected early February.

Watch the Full Interview Video:

View fullsize

I just got back from SHOT Show 2026 in Las Vegas, and let me tell you, it was an action-packed trip! Over on our channels, we’ve just dropped a fast-paced highlight reel that captures the best moments of our week long stay.

The SHOT Show took place at the Venetian Convention Center, and you’ll see plenty of footage capturing the scale and energy of the event itself: busy show floors, massive booths, indoor and outdoor areas, and the overall atmosphere of one of the largest firearms and shooting-sports events in the world, with Airguns and related gear naturally woven throughout.

But it’s not just airguns, we’ve got slices of Vegas! You’ll catch us strolling Fremont Street, lounging poolside, and soaking up those iconic Vegas vibes between interviews. Whether you’re here for the Airguns or the atmosphere, this video’s got it all, music, cuts, the show floor, and a taste of Las Vegas. Check it out now and immerse yourself in the SHOT Show experience!

I was in Las Vegas last week for SHOT Show, filming content for Replica Airguns, but I wanted to post a quick update so you know what I was up to.

I went to SHOT Show to connect with people in the industry and record a bunch of interviews with vendors and companies, Airgun and aintball brands included (and more). I ended up filming about seven interviews, and now that I’m home I’ve got a lot of great footage to go through.

I was in Vegas with my buddy Steve (the guy behind the camera). Once the filming was wrapped, we spent some time enjoying the city after a busy week. We also did a few things outside of SHOT Show, because if you’re in Vegas, you might as well experience it.

In this video, we’re at the Montecristo Cigar Bar inside Caesars Palace, winding down with a nice port and a cigar.

Stay tuned,now that I’m back, I’ll start editing and posting those interviews. If you want to watch the SHOT Show interview series, head over to Replica Airguns or watch on our Vimeo and YouTube channels as I post them…

View fullsize

In this Field Test Shooting Video I take a look at the KJ Works KP-19S. I’ve reviewed the KP-19 in the past, so this one should perform similarly, but it’s been a while and I wanted to get this one out for a proper range session.

I’ve already done a tabletop / close-up video for the KP-19S covering the specs, features, and up-close details, so if you want the full walk-around and all the technical info, make sure you check that out first.

For today’s session, I focused strictly on performance in the same basic field-test format: velocity testing, then a 10-shot accuracy group at 30 feet, and finally some overall shooting impressions.

Velocity Testing (Chronograph)

For the chronograph test, I ran 0.25g Airsoft BBs (not 0.20g), so expect the readings to come in a bit lower than what many people quote online.

My chronograph also decided to be difficult today, throwing “Error 2” messages and not registering shots consistently, so I had to keep working at it until it finally started giving me some readings.

Once it cooperated, I got five velocity readings:

• 312 fps, 304 fps, 293 fps, 288 fps, 284 fps:

• Average of 296 fps

A couple notes to keep things fair:

• If I had started the test with zero shots fired beforehand (the way I normally try to do it to maximize “fresh CO2” performance), the first shots could be a bit higher.

• Because this was with 0.25g BBs, if you ran 0.20g BBs, you’d likely see higher numbers, potentially into the low-to-mid 300s depending on conditions.

• This model also includes an extended barrel option that can push velocity higher, but I didn’t test it that way because most people run the pistol in its standard configuration (without a long exposed barrel sticking out).

Accuracy Testing (30 Feet)

For the accuracy test, I put a paper target at 30 feet and fired 10 rounds. The nice thing here is that the pistol should lock back on the last shot, so it makes it easy to confirm you’re done without having to count.

Results were excellent for a quick out-of-the-box test:

• With the exception of one flyer, everything was within about an inch

• The group was well-centered left-to-right

• Elevation was also very good without any sight adjustments

There isn’t much you can do for sight adjustment on this one unless you add a laser or optic, but you can tweak elevation slightly via hop-up, depending on your setup.

View fullsize

Final Thoughts

This pistol performed really well for me today.

The KJ Works KP-19S has that 1911-style trigger feel, light, short, and responsive, paired with a snappy blowback that makes it fun to shoot. Velocity was consistent once the chronograph started behaving, and the 30-foot grouping was far better than I expected without any tuning.

Aesthetically, it’s also a great-looking gun: a tactical, modern two-tone style with a double-stack magazine look that gives it that “2011 / hi-cap tactical 1911” vibe. If that’s the style you’re after, the KP-19S is a strong choice.

It should also work with most KJ Works tactical 1911 / double-stack style magazines, so if you already own similar KJ Works pistols, you may be able to mix and match mags. You can also run green gas magazines, but velocity will generally be lower. If you do choose to run the extended / threaded barrel setup, you can hide it with a mock compensator, but it will turn the pistol into a longer, bulkier package. Personally, I prefer it in the standard configuration.

Where to Buy

You can check this pistol out in our Canada Store (and possibly the US Store, depending on availability). I’ll include links where applicable, along with general store links where you can browse airguns, BB guns, airsoft guns, pellet guns, blank guns, and accessories.

Thanks for watching and reading, don’t forget to subscribe, and follow us on Facebook, Twitter, and Instagram. And yes, we’re back on YouTube after being gone for years. We’re re-uploading older content from Vimeo manually, so it’ll take a bit to get everything restored, but all new videos should be going up on YouTube as well going forward.

View fullsize

I had the chance to take the KWC 18 CO2 Blowback BB Pistol out for some shooting today to see how it performs. It’s a Glock-styled 4.5mm steel CO2 BB pistol with full blowback and selectable semi and full auto. It’s not an officially licensed Glock, but if you own (or have shot) Glocks, the controls and overall feel will be instantly familiar.

I’ve already done a close-up tabletop video for the KWC 18 covering specs and details, so if you want the up-close visuals and feature breakdown, make sure to check that out first.

For this session I concentrated solely on performance: a quick 5-shot chronograph run in semi-auto to record velocity, a 10-round semi-auto group at 30 feet, and then a full-auto mag dump to get a practical feel for controllability and “real world” accuracy—right out of the box (no tuning).

Velocity Testing (Chronograph)

For the chronograph testing, I ran five shots in semi-auto with a brand new CO2 in the magazine. The numbers came in at 293, 294, 282, 290, and 282 fps, for an average of about 288 fps. The spread was tight and the pistol felt extremely “snappy” while shooting, there’s a lot of pop in the blowback and you can feel it cycling hard.

One important note: this is a single-action-only style system, so you do need to rack the slide to cock it before it’ll fire (ask me how I know…).

View fullsize

Accuracy Testing (30 Feet)

For accuracy, I put a paper target out at 30 feet and fired 10 rounds in semi-auto. After a quick adjustment (the pistol was hitting very low at first), I aimed higher and got a roughly 3-inch grouping. The group was well centered left-to-right, but the pistol was still shooting noticeably low overall.

This is the kind of thing you’d simply keep in mind while shooting, and depending on the setup, you may be able to tweak elevation a little (but with steel BBs at short range, don’t expect miracles).

Full Auto (Mag Dump)

Then I loaded up and did a full-auto mag dump. As expected, it was basically spray-and-pray at 30 feet. The rate of fire is insane, and between that and the strong blowback, it was extremely difficult to keep rounds on target. I may have only landed a couple hits on paper.

Final Thoughts

All told, the KWC 18 is a really fun Glock-style blowback BB pistol if you want something that feels familiar in the hand and delivers a crisp trigger with serious recoil-like blowback. In semi-auto it’s manageable (even if it shoots low out of the box), but in full auto, at least at 30 feet, it’s more about the fun factor than practical accuracy.

• Buy the 18 CO2 Blowback Steel BB Pistol in Canada

• Buy 18 CO2 Blowback Steel BB Pistol in the US store

I was away for a bit on a well needed vacation in Kona Hawaii but I’m back now and ready to dive back into things so get ready for more reviews! In this December Massive Mystery Unboxing, I crack open a stack of newer Airsoft and BB guns that landed in the Replica Airguns inventory. Full shooting reviews are coming later – this is your quick spec rundown so you can see what’s what at a glance.

View fullsize

A&K M1873R M-LOK Lever Action Airsoft Gas Rifle

Modern M-LOK handguard wrapped around a classic 1873 lever-action with real wood furniture. Western vibes with tactical mounting options.

• Type: Lever-action airsoft rifle (gas, non-blowback)

• Ammo: 6mm plastic airsoft BBs

• Power: Green gas (internal reservoir)

• Weight: ~2180 g / 4.8 lb

• Velocity: ~350–400 fps with 0.20 g BBs

• Magazine Capacity: 25-round internal magazine

View fullsize

ESG B-10 Gas Airsoft Shotgun

Bullpup “evolutionary shotgun” with a single barrel, selectable 5 or 10-round burst, and an internal gas reservoir in the stock. Uses standard M4-style AEG mags for capacity.

• Type: Gas-powered bullpup airsoft shotgun (single-barrel, burst)

• Ammo: 6mm airsoft BBs

• Power: Green gas (internal reservoir in stock, HPA-convertible)

• Weight: ~3140 g / 6.9 lb

• Velocity: Roughly mid-300s fps, often listed around 370–400 fps with 0.20 g BBs

• Magazine Capacity: 105-round mid-cap G&G GOM V2 magazine

View fullsize

G&G L85 Carbine ETU Airsoft AEG Rifle

British bullpup classic with modern electronics – ETU, MOSFET, and selectable semi / full-auto or semi / 3-round burst, plus blowback for added realism.

• Type: Airsoft AEG rifle (with ETU and blowback)

• Ammo: 6mm airsoft BBs

• Power: Electric (LiPo-ready AEG)

• Weight: ~6 lb / 2.7 kg

• Velocity: ~370–400 fps with 0.20 g BBs (store range 350–400 fps)

• Magazine Capacity: 450-round hi-cap magazine

View fullsize

G&G PCC45 Pro M-LOK Airsoft AEG SMG

Compact .45-style SMG with a lightweight polymer receiver, slim M-LOK front end, and G&G’s Gen.4 MOSFET & ETU. Great choice for a fast, modern CQB/field hybrid build.

• Type: Airsoft AEG SMG

• Ammo: 6mm airsoft BBs

• Power: Electric

• Weight: ~4.44 lb / 2.0 kg

• Velocity: ~360 fps (overall range 350–400 fps with 0.20 g BBs)

• Magazine Capacity: ~105-round mid-cap PCC45 mag

View fullsize

KJWorks KP-19S Hi-Capa GBB Airsoft Pistol

A race-style Hi-Capa with ported slide, fiber-optic sights, threaded barrel and an adjustable “speed” trigger. Runs on both green gas and CO2, with a non-blowback system for efficiency and consistency.

• Type: Hi-Capa style gas airsoft pistol (non-blowback)

• Ammo: 6mm airsoft BBs

• Power: Green gas or CO2 (compatible mags)

• Weight: ~0.9 kg / ~2.0 lb (listed as 0.89 kg)

• Velocity: ~366 fps (FPS range 350–400 fps)

• Magazine Capacity: 25-round magazine

View fullsize

KWC K18 CO2 Blowback Steel BB Pistol

Glock-18 style CO2 BB pistol with select-fire (semi and full-auto), metal slide, polymer frame, and full blowback. Great fun-factor steel BB blaster with 4.5mm ammo.

• Type: CO2 blowback BB pistol (select-fire, semi / full-auto)

• Ammo: 4.5mm (.177) steel BBs

• Power: 12 g CO2

• Weight: ~0.8–0.9 kg / ~1.7–2.0 lb

• Velocity: ~314 fps with steel BBs

• Magazine Capacity: 18-round drop-out magazine

This will be my final Interview Video for SHOT Show 2025. I did get to talk with someone from Crosman but the Daisy rep was not around totally with so I did my best to talk about a couple of the Daisy products that I felt were interesting. If you are not aware, Crosman and Daisy have now joined forces together along with Gamo, Benjamin and SPLATRBALL so all of these product were on display at the Crosman Daisy Booth. I focussed on the Crosman M1 Full Auto Carbine and their updated all black ST1 Full Auto BB Rifle. We then took a look at some of the Game Face Airsoft Products and then I performed my own Interview/Review for Daisy talking about the Woodland Trail Model 1911 and Model 25 Lever and Pump Action BB Rifles.

• Buy Replica Airguns in Canada

• Buy Replica Airguns in the US

I had the pleasure of interviewing Mark from Umarex again at SHOT Show 2025 and Mark went over some of the new products from Umarex coming out this year. Make started of by showing me two new MOS (Modular Optic System) Gen 5 Glocks in a Glock 17 and Glock 19 versions. Both come with Umarex based red dot sights but you can change them up for something different if you choose to down the road. We then took a look at the new Umarex AER16 AR AEG Rifle in 4.5mm Steel BB rather than 6mm Airsoft similar to the Barra e400 that came out last year. In a nutshell it is a battery/spring operated 4.5mm Steel BB Full Auto AR Replica. Mark then showed us some A&L AK based AEG Airsoft Rifles they are now distributing that feature Full steel body construction with high-quality real laminated wood handguard and skeletal folding stocks. These are one to one in terms of size and weight adn very detailed. We then finished up the interview taking a look at the Legends Saddle Lever Action Shell Loading Rifle and the Umarex Smith & Wesson Competitor Shell Loading revolver.

Luckily I was able to find some time with James again this year and James gave us all the new details on some of the KWA updated and new products. Starting with the KWA ATP-Z Blowback Airsoft Training Pistol added recently to the KWA lineup, James also showed us a few versatile Carbine Pistol Kits made specifically for the ATP-Z and ATP-GT Pistols. Not yet fully released, James went over their updated TAC-9 hopefully coming out this year. We then got a nice tour of the updated Radian Model 1 AEG Airsoft Rifle with built in recoil system also built into KWA’s Q10 AEG Airsoft Rifle.