If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.

Main points covered:

• Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.

• What is an Uncontrolled Airgun and Airsoft Gun?

• What is an Uncontrolled Blank Gun / Starter Pistols?

• What about Fully Automatic Airguns and Airsoft Guns?

• What about Replica Guns?

NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate. 

MEMORANDUM D19-13-2

Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.

“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:

Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.

NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)

Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile. 

Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).

NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?

NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).

Replica firearms:

“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.

For a device to be a replica firearm it must meet all three requirements:

• (a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);

• (b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and

• (c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm. 

RCMP Website "Air Guns"

1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code

These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.

These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.

Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.

High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm. 

Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.

This YouTube video was made to touch upon the tragic shooting and death of a young man at the Beavercreek Walmart in the US. The tragedy was the result of poor judgment and misunderstanding of the situation that started with John Crawford (22) deciding to walk around a Walmart store with a very realistic looking replica Air Rifle. Subsequently in the midst of all the excitement as customers ran out of the store, Angela Williams (37) had a medical emergency that also cost her her life. 

Below is an outline of YouTube video that follows:

John Crawford 22 Years old was shot  by police in a Beavercreek Walmart while holding a Crosman MK-177 Pellet BB gun.

Another death as a result: Angela Williams, 37, was with her 9-year-old daughter and suffered a medical emergency and died as a result as people attempted to flee the store amongst the panic.

John Crawford is Survived by: LeeCee Johnson, 22 Mother of Crawford's children (Believe he had 2 children)

NOTES: 

• Walmart US keeps these guns on shelf in the box generally, but not locked up or behind glass.
• In Canada Most places keep even Airguns behind locked glass. 

The weapon (Crosman MK-177), which can shoot both pellets and BBs, had been removed from its original packaging, was this done by John Crawford or was it already unpackaged when he picked it up?

Ronald Ritchie made the original 911 call, I listened to two of the police 911 phone call recording and he seemed to be talking level headed and not making it out to be anything more than what he saw which was a black man walking around a Walmart with what looked like a real rifle. John Crawford was holding the rifle while he had his phone between his shoulder and ear, John was fiddling with the rifle and looked to be trying to load it. Ronald Ritchie said John was periodically pointing it at people (which may or may not have been intentional).

LeeCee Johnson, 22, who identified herself as the mother of Crawford’s children, said she was talking to Crawford on her cell phone at the time of the shooting:

“We was just talking. He (John) said he was at the video games playing videos and he went over there by the toy section where the toy guns were. And the next thing I know, he said ‘It’s not real,’ and the police start shooting and they said ‘Get on the ground,’ but he was already on the ground because they had shot him,” she said. She added she “could hear him just crying and screaming” and said officers “shot him down like he was not even human.”

First and Foremost, this event is very tragic and my condolences go out to the families and friends of John Crawford and Angela Williams.

Questions we need to ask ourselves:

• Why was John Crawford walking around the Walmart with what looked like an "assault rifle" in a very public location?
• With all the public shootings these days, why would you walk around a public Walmart with what looks like a very real and threatening rifle, similar to the kinds used in these types of shootings in the past?
• Why did the police seem so quick to shoot John down? Where they a bit eager or hyped up? It would be very interesting to see the surveillance video for this tragedy?
• Why are very realistic Airguns on open display and so easy to attain? Keep in mind even a regular break barrel Airgun looks like a real rifle to most people.

What is so damaging about all this:

• This will add "ammunition so to speak" for bureaucrats and authorities to question if Airguns should look realistic, or if they now need to have bright colored markings all over them so people will assume they are not reel? Or perhaps outlaw them completely or make them very hard to attain for the average person.
• Now the general public will have yet another reason to have a negative view on Airguns. I fear that putting more restrictions on airguns is just a stepping stone to more restrictions on real guns and more restrictions on our rights overall.

What ever happened to common sense? It has become uncommon these days…

 Based on how easy it is for a person to get their hands on very realistic looking Airguns in most US based retail stores, I am surprised this tragedy has not happened already, or more often.

Would you walk around your neighborhood with what looks like an Assault rifle? So why walk around a Walmart with one?

Unfortunately we can not protect everyone from themselves, the more failsafes we put in place, the less reasonability people have for themselves and the more responsibility it seems is placed on businesses, government, organizations, parks and events…

We even need warning labels on our coffee telling us it's hot, or to not put poison in our mouths, there are railing and barriers around any bit of water or slight ledge.

Society is programing people to think less fore themselves and trust that everything is going to be OK.

Well it's not true, there is still something called survival of the fittest no matter how many safety nest are in place.

We need to spend more time teaching our kids how to act and behave and how to think for themselves and not be so dependent on everyone else to protect them from themselves. Don't  leave it up to the TV, movies, video games or even their just as oblivious friends. 

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

Is an Airgun Good for Self Defense? Another one of those questions I get asked fairly often that's a bit hard to answer in a few sentences... Not all of us have easy access to a 9mm pistol or even a rifle but many of us can get our hands on an airgun fairly easily and they look real enough, I guess that is one thing they have going for them.

But what if the mere sight of what looks like a gun does not scare an intruder off? If you where hoping that would be enough, you may just be out of luck and what if you just brought an Airgun to a "real" gun fight? You are going to be drastically "outgunned" pun intended and here's why. A 4.5mm Steel BB weighs about 5.1 grains and generally you are looking at about 2-3 foot pounds of energy from a CO2 BB gun. Even a .177 caliber lead pellet is only marginally heavier at around 7-8 grains and if you're really lucky you might just get 4 foot pounds of energy out of a CO2 pellet pistol.

So let's take a look at a fairly conservative "real pistol" rounds, the 9mm. The 9mm rounds come in different bullet weighs but you can get a 120 grain 9mm in a plus p ammo with as much as 400 foot pounds of energy and even with that much raw power, many people claim that a 9mm round does not always have enough stopping power to put down a person even when shot multiple times center mass. It just depends what vital organs or arteries you hit that determines if he gets lucky or you get lucky.

Your 5.1 grain 4.5mm Steel BB is not going to do anything if it hits any type of clothing and even if you find some flesh it's just going to piss off the intruder.

My suggestion is to consider a bat or a golf club or a really big knife or just about anything other than an airgun because if the sight of the airgun replica does not scare an intrude away then you are really buggered.

Keep in mind that you need to abide by any laws regarding the use of self defense in your areas. Even just physical force could be considered a crime and at the end of the day you are ultimately accountable for your actions.

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.

This is take 2 of my Modification to my F1 Chrony Chronograph. The purpose of this modification is to improve the low light FPS readings. In my first attempt I used LED Puck Lights but they where the kind that used flat panel LED's and they only had 4 panels per LED Puck which made each LED panel kind of bright. I did get OK with my first mod using LED Puck Lights but not as good as I would like to see.

So here we are with take 2 of F1 Chrony Chronograph LED Puck Light modification and this time around I am using standard bulb styled LED lights and to improve my chances of this working I went with and LED Puck that contained 24 LED bulb lights per puck, this way each light on it's own is a bit dimmer which I feel will give a more diffused lighting effect and hopeful consistent fps readings.

By the way I got these LED Puck Lights at my local dollar store for $2.50 each so not a very expensive modification, especially if they work.

Well... Watch the video and see how they perform...

This video was made to show you the results I got by mounting LED puck lights to the top of my F1 Chrony Chronograph defuser panel in order to improve the low light Feet Per Second readings when using 4.5mm Steel BB's.

I have been struggling with my F1 Chrony Chronograph during the fall and winter months as tit becomes overcast and dark where I live. There have been days where I have gone out to shoot my field test shooting video and not been able to get any Chronograph fps results which is very frustrating because much time and effort goes into the planning setup of each video.

I was given advice from several of my viewers to mount an LED puck style light on the back side of my Chronograph defuser panel and that this helps the Chronograph to read much better in low light situations.

I bought a multipack of the LED puck lights from my local Costco but they did not work as well as I expected them to as they had a panel style of LED rather than the bulb shaped LED which I think may diffuse the light a bit more. My next experiments will be done using LED Puck lights but with the bulb styled LED.

You can watch my video to see how my first attempt using an LED Puck light with my F1 Chrony Chronograph worked out.

In this informative video I go over the very basics of gun "handling" safety. I don't talk about gun storage or even shooting of the gun, I strictly go over the main aspects of handling a gun in a safe manor.

These are the four main points I demonstrate in this video:

• Fingers off the trigger till you are ready to shoot.

• Keep the gun unloaded till you are ready to shoot it.

• Assume your gun is loaded at ALL times.

• Always point your gun in a safe direction.

Hopefully this video will prevent some unfortunate accidents, even airgun related accidents can cause serious injuries which in most cases can be prevented with the correct gun handling information.

I have made a

similar safety video

where I talk about general gun safety and speak more about storing and also some gun shooting safety tips.

You really need to watch my Vimeo Video to see how easy it is to take a brand new out of the box gun and give it that weathered, old, worn and used look that you would find in a classic vintage gun like a Luger P.08, Colt 45 1911 or any other classic firearm. Of course this is something you would do to a new gun that you want to make look old :)

This is a great way to take a gun that already has some wear marks on it and really give it the full worn in look, kind of an alternative to having to touch it up or refinish it.

Here is a hint... I use something magical to do it!

Buy the Umarex Luger P.08

One of the most important keys to shooting accurately is how you grip the gun! In this video I show you the two handed grip that I use and that I have learned from watching other accurate shooters. I also talk about arm and shoulder placement which is more important when shooting large caliber pistols but even when shooting airguns that have virtually no recoil you may as well practice the correct hand arm and shoulder placement for when and if you do start shooting heavy recoil guns.

The main hand grip points I talk about in this video are how to overlap your finders and thumbs and also the pressure used by each hand that will make all the difference down range when shooting at targets.

Watch my Vimeo Tutorial Video on the Best Two Handed Pistol Grip:

Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.

The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...

In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.

Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.

Buy KWC/Cybergun 1911 BB in Canada   -   Buy KWC/Cybergun 1911 BB in the US

I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...

Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

I have been asked so many times to make a "How To Video" on cleaning Airguns and Blank Guns so I thought I better make the video so people stop asking me to make one :) and if they do ask, which I am sure they still will, then I will be able to direct them to this awesome video tutorial...

So basically in this video I clean an Airgun that can be field stripped and I also clean an Airgun that can not easily be field stripped. I then clean a blank gun even thought the process is very much the same.

I also talk a bit about cleaners and general air gun maintenance but for the most part I just show you how to clean the guns so watch the video!

The CBSA (Canada Customs) has posted some good news for a change about the Reclassification of Airsoft Guns that shoot over 366fps! (Customs Notice 12-005)

So what does this mean? In a nutshell, any Airsoft gun that shoots a .20 gram airsoft BB at over 366 fps is now considered an uncontrolled firearm just like a regular airgun. And so it can be made out of full metal and look exactly like a real gun even without the red tip. (before the threshold was .22 gram BB had to shoot over 407 fps)

This means we will now be able to bring a lot more "All Metal Replica" Airsoft guns into Canada that where previously not allowed because of our much higher feet per second restrictions.

Here is the official statement from the CBSA:

1. The purpose of this notice is to advise of changes affecting the classification of 6mm calibre airsoft guns.

2. Section 2 of the Criminal Code defines a firearm as “a barrelled weapon from which any shot, bullet or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barrelled weapon, as well as anything that can be adapted for use as a firearm”.

3. As outlined in Memorandum D19-13-2, Importing and Exporting Firearms, Weapons and Devices, it was previously established that an airsoft gun, firing a .22g 6mm plastic pellet, must have a muzzle velocity in excess of 124 m/s (407 fps), in order to be considered a firearm.

4. Based on the latest research, it is now established that the muzzle velocity at which a .20g 6mm plastic airsoft projectile is capable of causing serious bodily injury is 111.6 m/s (366 fps).

5. Airsoft guns, firing a .20g 6mm plastic pellet, with a muzzle velocity above 111.6 m/s (366 fps), will be classified as firearms. Please refer to D19-13-2 for the import requirements of low muzzle velocity firearms, including low muzzle velocity “uncontrolled” firearms.

6. If an airsoft gun, firing a .20g 6mm plastic pellet, shoots below 111.6 m/s (366 fps), and resembles with near precision an existing make and model of a firearm, other than an antique firearm, it will be classified as replica firearm. Replica firearms are prohibited devices and must meet import requirements as listed in D19-13-2.

7. Inquiries and comments about this notice should be directed to: Other Government Department Programs Unit Programs Branch Canada Border Services Agency E-mail: faw-aaf@cbsa-asfc.gc.ca

Update on 2012-03-03 07:19 by Michael Kaye

Here is the direct link to this Customs Notice 12-005 on the CBSA website!

I have found one of the more confusion aspects of guns is what defines the trigger action, and I confused this a lot at first but now feel I have a good understanding of what makes a gun Single Action Only, Double Action Only or Single and Double Action.

Your best bet is to watch my attached Vimeo video as it not only describes trigger actions but also has the added benefit of the visual examples of each type of trigger action.

Here is a very quick explanation of what constitutes each type of trigger action:

First off the action is based on the role of the trigger in how it effects the action, not how the slide or the hammer can effect the action of the gun.

A Single Action Only gun does one action (a single action) and that is generally the releasing of the hammer or striker or what have you... Single Action Only guns can not fire without first manually pre-cocking the external hammer or manually pulling the slide or charging handle back first to chamber a round and also pre-cock the action of the gun. Keep in mind that the blowback of the slide or bolt in semi and full auto guns effectively cocks the action of the gun allowing for single action trigger release.

A Double Action Only gun performs dual functions, the pre-cocking of the hammer or striker in the first stage and the releasing of the hammer or striker in the second stage, therefore performing two actions. Double Action Only guns do not have the ability to pre-cock the hammer or striker fully and therefore generally have a heavier trigger pull as the first stage of the trigger is to cock the sprung hammer or internal action.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Single and Double Action guns have the ability to do both, meaning they can be pre-cocked and then fired or fired without pre-cocking simply by pulling the trigger.

Keep in mind that there are some guns that fall in to their own category, take for example the Glock. Glock has been known to actually describer their guns as Double Action Only, when in fact they can not be fired without the slide first being pulled back to partially pre-cock the internal striker - similar to a single action gun. But when you pull the trigger on a Glock you do not simply release the action but rather the trigger first pulls the striker action back the final stage in order to release it, similar to a double action gun.

Again, watch my Vimeo video as I hope the visuals will help you to understand the differences between Single Action Only, Double Action Only and Single and Double Action trigger.