In this "head to head to head" pistol shootout I compare three of my more powerful, or you could say effective air pistols against each other. Shooting at some pop cans from about 30 feet away to see how destructive each one is. I don't generally recommend air pistols for pest control simply because they tend to be less accurate and powerful than rifles, especially out at the longer ranges where a magnified scope is required and notably where the pesky vermin like to hang out.
I would have to say out of the three tested in this video comparison, the Webley Alecto in .22 caliber and the Modified Drozd Full Auto BB Gun would for sure get the job done at closer ranges. The Webley Alecto simply because it can hurl a heavy grain .22 caliber lead pellet right around the 500 fps mark which will take down small pests, again at close ranges.
My second choice or even first choice depending on how active the pest are would be my modified full auto 1200 rounds per minute Drozd that hurls 4.5mm Steel BB's at over 500 fps (under 4.2 foot pounds) at a rate of 20 BB's per second! A 4.5mm Steel BB traveling at 500 fps will penetrate fur and feathers very well and with most of the 20 BB's hitting a target in a matter of 1 second, that is going to humanly put a small to even medium sized pest down for sure. And yes the Drozd becomes a pistol when yuo take the rear stock off ;)
My last choice for the job is the Xisico XSP180 in .177 caliber since like the Webley Alecto it is only a single shot, so you got to make it count and being that it has less overall energy than the Webley Alecto again I would prefer the Alecto over the XSP180.
Watch my "head to head to head" Vimeo video to see how these three pellet pistols compare:
Another quick revisit of the KWC/Cybergun M92 Beretta - Taurus full metal, full blowback, CO2 4.5mm Steel BB pistol series. They come in several flavors but are all made by KWC and in many cases redistributed licensed by Cybergun. This Field Test Shooting Video Review focuses on the Cybergun Swiss Arms P92 version.
Now that I have a more standardized Field Test Shooting format, I though I would revisit this series of KWC/Cybergun Beretta - Taurus Replica BB Pistols and do a follow up Field Test to get some more camera angles and hopefully a nice tight target grouping using my standard semi rested position from 20 feet away.
I also incorporate some high speed video near the end of this Field Test Shooting video Review to go along with the Chronograph and target portion of the Filed Test Shooting review.
The KWC - Cybergun Full Blowback All metal serious of Replica CO2 BB Pistols has been hugely popular over here at Replica Airguns and for good reason, they are very realistic in looks and operation, are priced very respectably and replicate several of the more popular semi auto pistols.
Action: Semi auto, double action only with blowback.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 15 round stick magazine.
FPS: 380.
Trigger Pull: The Double Action Only trigger pull on the Umarex Walther P99 CO2 Blowback Airsoft Pistol is long but not overly heavy for a double action trigger, it does have a break point mid way where it locks partway back, I presume this is the point in which a BB is loaded from the magazine into the barrel? The rest of the pull is still medium but much shorter with a distinct release point.
Accuracy: I did do a quick preliminary test before I made this table top review to get an idea of where this gun performs in terms of FPS and accuracy, I shot 5 rounds through my Chronograph on a fresh CO2 and got an average of 333FPS which was a bit lower than the claimed 380 but it was not the hottest of days. I also stepped back 20 feet and from a semi rested position I was able to get 9 shots within 2 inches of each other which was not bad for a DAO gun that I have never shot before. I did shoot a bit down and to the left with the set sights.
Build Quality: The Umarex Walther P99 is well built for its rather low price tag, it may not have all the bells and whistles but it does get the job done with good fit and finish and materials used. You will find a plastic/polymer frame but there is a lot of metal where it would normally be found on the real steel version like in the slide, magazine, trigger, slide catch, magazine release, inner barrel and many other internal parts. No real complaints here!
Realism: The Umarex Walther P99 CO2 Blowback Airsoft Pistol is pretty close in looks to a real steel Walther P99 with the exception of a missing decocker, but I'm pretty sure this is the same with the real steel DAO version? There is also the funny looking safety on the right side of the frame found on many Umarex airguns. I have to mention the red tip but again this can be removed and even when removed the barrel it is still recessed which adds to the realism. The Blowback action, Walther licensing and nice heavy weight all add up to make this Airsoft pistol look and feel the part.
Metal slide and internal parts gives it decent weight.
Rail for accessories.
Well hidden CO2 screw.
Walther licensing.
Recessed inner barrel.
White dot sights, easy to use.
Right amount of power for indoor CQB style airsoft games.
Cons:
Comes with a red tip even in Canada.
Double action only, so trigger is a bit heavier.
Kind of funny safety, not like the real gun.
Blowback was a bit sluggish.
Comments:
Overall the Umarex Walther P99 CO2 Blowback Airsoft Pistol is a very good buy, it's a decent replica of the real steel Walther P99 with blowback operation, lots of metal parts, good fit and finish, decent performance and full Walther licensing and trademarks. All at a very affordable price tag. It may lack some of the extras you will find on more expensive and more functional Airsoft pistols but the simplicity of the Umarex Walther P99 CO2 Blowback Airsoft Pistol means it will most likely be a bit more reliable with less to go wrong down the road. If you have been looking for a nice Walther styled replica in an Airsoft version this may be just be the ticket!
My Vimeo Video Review for the Umarex Walther P99 CO2 Blowback Airsoft Pistol:
I will be doing proper Table Top and Field Test Videos for each of these Airsoft guns as soon as I can get to them all, starting with the Umarex Gas Blowback H&K MP7 A1 Airsoft PDW so stay posted for these upcoming video reviews...
After many many requests to show how the Umarex Walther PPK CO2 Tab Modification is done I have relented to public demand. I don't actually cut my tab in this PPK CO2 Tab Modification Video but I do go step-by-step in detail and compare my modified Umarex PPK to my unmodified Umarex PPK. It is really very basic on how this is done and only a hack say and perhaps a file are all that is required to make the modifications to the PPK CO2 tab in order to make it flush with the bottom of the handle area.
Your best bet is to simply watch my YouTube Video located below and follow the steps there but here it is in text form:
Place an empty (already pierced) CO2 into your Umarex Walther PPK and tighten the unmodified CO2 tab until fully tightened, just like you would tighten a fresh CO2.
Take note at how many threads are exposed between the bottom of the handle and the top of the plastic CO2 tab, there should be about 2-4 threads exposed.
Unscrew the CO2 tab all the way, place the PPK BB Pistol so it is secure (in a vice of some sort) and use a hacksaw or dremel to shorten the CO2 screw just above the plastic tab at the thread location you previously noted. Be conservative as you can always cut or file the screw a bit shorter if your first cut was not short enough.
Now use the same hacksaw or dremel to cut a notch in the exposed cut area of the CO2 screw so that you can use a slot screwdriver to tighten the CO2 screw.
That's it - Enjoy your modified Umarex Walther PPK CO2 BB Pistol!
Watch my Vimeo Video of the Umarex Walther PPK CO2 Tab Modification Tutorial:
This is not meant to be a full review of either the BB or Airsoft version of the Cybergun - KWC CO2 Blowback Mini UZI's but I do talk about specifications, show you around both guns, and put them both through a full Field Test so I guess in a way, perhaps it can be considered to be a full review ;)
I will list the specifications here for you but I am not going to get into details like Trigger Pull, Build Quality, Accuracy and Realism. You can check out my other video reviews for more information on the Mini UZI:
As I said you can check out all my other videos for info on these very accurate Mini UZI Replicas, I mainly want to go over some of the main differences and similarities for both the BB and Airsoft versions.
In terms of build quality they are made almost exactly the same and weigh in at a hefty near 5 pounds, the only differences are the inner barrel and magazines to accommodate the different sized ammo. The BB version has a 25 round single stack magazine that does not have a follower to stop the bolt from continuing to operate even after the magazine is empty. While the 6mm Airsoft version has a double stack magazine that holds 38 rounds and does have a follower to stop the bolt which can save you some unintentional wasted CO2.
The Airsoft Mini UZI version is distributed by KWC while the 4.5mm BB version is distributed by Cybergun, you will find the UZI and IWI licensing on the Cybergun 4.5mm BB version but not on the KWC 6mm Airsoft version.
Out of the box the KWC Airsoft Mini UZI is ready to go in both semi auto and full auto while the 4.5mm steel BB version will only shoot in semi auto mode, it can however be easily modded to shoot in full auto.
Both guns come in cardboard boxes with manuals, some BB's and an Allen key to tighten the CO2. The KWC Airsoft Mini UZI also comes with a handy speed loader.
There is a slight fps velocity difference between the two with the KWC Airsoft 6mm plastic rounds traveling at around 400 fps (with .20 gram BB's) and the 4.5mm Steel BB's traveling at right around 350 fps. In the field test portion I test both guns out on some water filled cans to see how each ammo type performs in terms of penetration.
Your best bet is to watch both my Table Top and Field Test Comparison Video Reviews and see for yourself how they compare!
One question that comes up often is the danger attached to blank gun use and the most common question I get is about the danger of shooting a blank gun at a person. Blank guns have many uses, one of which is to be used as a prop in a movie or reenactment. In this situation one may want to point and shoot a blank gun at a person to make teh scene more believable it. If the person is far enough away there is usually no cause for concern but with that said I would personally point the gun just off to one side in the event that something might come loose within the gun barrel or perhaps a fragment of something where to be fired and cause an injury to the person the gun is directed towards. With creative camera angles you shouldn't need to actually point a blank gun directly at anyone.
People also assume that because a blank gun does not actually fire a bullet that it is relatively harmless. This is not true at all, in the larger caliber blanks there is about the same amount of energy to what your would find in a real bullet, this is so the blank gun will sound about as loud as a real bullet being fired. The difference with how the energy is released in a blank round versus a real bullet is that the bullet caries most of the energy with it and when the bullet hits its intended target, the bulk of the energy is transferred to that target.
The energy from a blank round dissipates almost immediately after it leaves the gun barrel but the energy right at the barrel tip is very similar to that of a real bullet, especially if it has nowhere to go but directly into an object. So yes a blank gun round can be lethal at very close ranges and unfortunately several people have paid with their lives finding this out for themselves.
With this newfound information about blank gun danger, some people might say... get rid of these dangers to society! Before we head in that direction think about how many other non vital things we have in our lives that I would have to say have claimed way more lives than blank guns could even come close to: Off-road pleasure vehicles, Skydiving, Skying, Pools, Real Guns to name a few! Blank guns also serve very useful purposes like being used to signal a warning or distress, send out flares, ward off wild animals, train people on how to use a real gun, and of course dog training. I am sure the good outweighs the bad here.
That's enough politics for now, juts watch the video and see for yourself why you should not point a blank gun at anyone, especially if the person is very close in proximity to you!
Trigger Pull: The trigger pull on the Cybergun Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the P226 in single action mode, the pull is light and the take-up is fairly short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action next shot, double action shots are still pretty light but much longer in order to cock the hammer.
Accuracy: Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor.
Build Quality: The build quality is generally good and I was surprised at the finish on this model as the paint is not showing any wear marks so far, the fit is good with minimal slide and barrel wobble and everything is working very well with no problems so far with a fair amount of shots through it, guess you could say I like shooting this gun :) Most of the gun is metal with only the grips and a couple internal parts being plastic.
Realism: The Cybergun Sig Sauer P226 6mm Airsoft pistol is a replica of the real steel Sig Sauer P226 right down to the licensing and it really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig and all the mechanical parts work just the same including a working de-cocker and adjustable front sight.
Seemed to shoot a bit low for me, could adjust with hop-up a bit?
Only one magazine per Gas fill.
Comments:
I am a big Sig Sauer fan so it would take a lot for me to not give this gun a good review, with that said it performed pretty well, sure it was not the most powerful but I was using gas over CO2 so I was not expecting too much, it also shot a bit low for me but again that may have been because of the barrel mod so who really knows for sure at this point ;) And yes it came with that unsightly orange tip that I took short work of removing. At teh end of the day I still love it and it performed well without letting me down, just like a would expect from a real Sig Sauer!
My Vimeo Table Top Review of the Cybergun Sig Sauer P226 GBB Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the RG-88 and RG-59 in single action is very light with the RG-59 having virtually no take up at all while the RG-88 has some take up but then a noticeable and predictable release point. Both guns have medium to heavy yet smooth double action triggers.
Accuracy: NA.
Build Quality: The overall build quality for the ROHM RG-88 and RG-59 blank guns is excellent, being German made they are built to last and the fit and finish is very good. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc metal with only the grips being plastic.
Realism: The ROHM RG-88 and ROHM RG-59 are not exact replicas of any given guns in production as this would make importing them into Canada even more difficult, but they do share similarities with some real guns in production. The RG-88 semi auto looks to be based around a Walther PPK design while the RG-59 has that Smith & Wesson Snub Nosed Revolver look to it. As for looking like and working like real guns, they do this very well, with the exception of the dangerous bullet coming out of the barrel!
German made quality, materials fit and finish is all excellent.
Almost all metal with some reenforced steel parts.
Nice light single action triggers on both guns with double action ability wehn needed.
Both are front firing with semi plugged barrels.
Come with flare adaptors and cleaning rods.
Seem to be some of the only blank guns we can get here in Canada right now.
Cons:
Not actual exact replicas of any specific guns in production.
The RG-59 only works with the .380 crimped, 9mm P.A.K. balnks are a bit too long.
Expensive due to them being harder to get and in high demand in Canada.
Comments:
As with pretty much all blank guns, they are mostly for show so it all comes down to how do they look and do they go bang when they are supposed to! In both cases they get top marks. Both the RG-88 semi auto and RG-59 revolver feel solid and the mechanical parts are tight and smooth giving a confident feeling when holding them. I like the larger caliber blanks over the .22 crimped blanks as they have a bigger bang but they will set you back in the cost department a bit more as the price for 9mm P.A.K. and .380 blanks will be a lot more than .22 crimped so keep this in mind when choosing a blank gun. If you're looking for a well made and dependable blank pistol then you really can not go wrong with any of the ROHM blank guns we sell in the Canada Replica Airguns Store.
My Vimeo Full Video Review for the ROHM RG-88 and RG59 Blank Pistols:
I usually do my Table Top Video Review first but this time around I did my Field Test Video Review first since I was all setup checking out a couple other guns at the time. When I do my detailed Table Top Video Review for the Cybgergun Sig Suer P226, I'll post the link here so stay tuned. If you have not already checked out my Barrel Mod Video for this same gun then check that video out where I remover the extended orange portion of the metal barrel and make the barrel flush with the end of the slide which is how the real steel version was originally made.
Getting back to the Cybergun Sig Sauer P226 GBB blowback Airsoft Pistol field test, as per usual I test this Airsoft semi auto gas blowback pistol on the Chronograph to see what kind of real world velocity I get and since I had some Green Gas on hand, I used it for this part of the review and got an average of 315 fps with a six shot string.
I also stepped back 20 feet and shot 10 times at my stationary target using a semi rested position (sand bag up front and kneeling in the back). Even though the Sig Sauer P226 shot a bit low I did get about a 1.25 inch group with the exception of one flyer that hooked down just a bit making the 10 shot group a bit wider at just under 2 inches. The low shot placement may have been caused by my barrel mod but since I did not do a before and after test, I can not say for sure?
Make sure to watch my YouTube Video of this Field Test as it also includes some nice slow-motion of the slide blowback at both 400 and 1200 frames per second.
Watch my full Video Field Test Shooting Vimeo Video below:
I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...
Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...
As with most new items I pickup, I like to share them with everyone. I am checking into some more ROHM blank guns, an RG-59 and RG-88, the RG-59 is a lot like the ROHM RG-56 .22 caliber blank revolver I sell in the Canada Replica Airguns Store but in .380 caliber and the one I show off here is a 5 shot two-tone model. Other than that they use the same frame and mechanical parts throughout.
I also received a black/blued ROHM RG-88 which is kind of like a Walther PPK in design, it field strips the same, has a similar safety setup and even has a similar size and look to it although it is definitely not a replica of a Walther PPK. I am impressed with the overall quality of the ROHM blank guns, material used, fit and finish is very good.
Lastly, I acquired a pre-owned Umarex CP99 CO2 Pellet Pistol from a customer of mine. It is in pretty much in new condition and is one of the Umarex guns I was missing in my collection and have been looking to add. The Umarex CP99 is a pretty good replica of the Walther P99 and uses the standard Umarex metal 8 shot rotary magazines and shares the same CO2 grip fed magazine as the CPSport. The CP99 is German made so it's not one of the lower cost Umarex pistols out there but you do get what you pay for ;)
I already posted that I recently hit 10,000,00 YouTube video Views but I have been hinting about there being another Giveaway/Contest. After much thought I wanted to have a way that more than just one person could benefit from this. So I decided to list a bunch of my Canada Store products on sale. (Sorry US customers but I have a lot more restrictions in the US when it comes to what I can do with my pricing).
These Canadian sales will be in effect from now until October 10th and to make things even better, one lucky shopper during this time will get their entire order for free (This includes US Customers too).
So make sure to get in on the savings and the chance to get your order free!
In this "Update Video" I also show off some new previously owned guns added to my collection, an Airsoft ASG shell ejecting CZ 75, a no-name KSC Airsoft shooter and a Gamo Combat .177 caliber pellet revolver. And if you're into spring piston break barrel pistols, make sure to watch for my customized Exisco XSP180 .177 caliber Verminator!
Ten Million Video Views Giveaway Plus CZ 75 - Glock Airsoft - Gamo Combat Pellet Revolver
Here is a sample of some of the items on sale right now...
When it comes to Airguns and Blank Guns, it's not often that an item is actually more money to buy in the US but with the Webley Alecto, it was actually more money in the US so I got to thinking, why not ship our Canada version to our US customers so they can save a few bucks! Both the US and Canada Webley Alecto are the same with only one exception, the Canada version has been detuned but this can be easily rectified with a simple valve modification (Instructions delivered after purchased from Replica Airguns).
Action: Electronic trigger with 1-3-6 round burst & 300-340-600 Rounds Per Minute.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 900 rounds.
FPS: 360-500.
Trigger Pull: The trigger pull on the IZH Drozd Blackbird is nice and light due to the fact that the trigger is not mechanical but is instead an electronic on-off switch that operates a solenoid. The solenoid pulsates in turn hitting the CO2 valve release. This is how the single fire and burst fire rates are achieved, by means of electronics.
Accuracy: The Drozd Blackbird is designed to be a machine gun and so testing it in single shot mode for accuracy is kind of taking it out of its element. Even so it did reasonably well, but when when I flicked it over to full auto it actually seemed to tighten up and start grouping even more centered and closer together considering the vast amount of rounds coming out of the barrel all at once :)
Build Quality: This is a typical Russian made gun, all business and less importance put on looks but even so it is visually appealing, at least to me! Everything works exactly as it should and even though the main shell is made out of plastic, it's really more of a weapons grade polymer so there is no cause for concern here. There are a fair amount of metal components like the factory barrel, much of the magazine and many internal parts. This air gun is very durable!
Realism: The Baikal Drozd Blackbird IZH MP-661K is not a replica, but it does look like a sub machine gun of sorts, I'm really just not sure exactly what it looks like as it kind of has its own look. When you start shooting it, looks just don't seem to matter anymore, all you can think about is how much damage is happening down range.
A bit more accuracy in semi auto mode would have been nice.
On the pricey side.
Comments:
The Baikal Drozd Blackbird IZH MP-661K takes all the fun you get with the Classic Drozd and gives you even more fun. It may be one of the more pricy BB machine guns on the market but it is well worth the extra cost to get such a quality product that not only is great out of the box but can also be modified in so many ways to improve its performance and looks dramatically. If you are looking for the absolute top player in the BB Machine gun category then the Drozd Blackbird is the top contender with its excellent build quality and performance along with the nearly unlimited modifications available to make the Blackbird perform up to anyones standards.
My Vimeo Video Review for this Russian made Blackbird BB Machine gun:
I'm kind of doing this one backwards this time around. I was going to do the table top review of the Baikal Drozd Blackbird first but the weather was just too nice to pass up today to not get outside and give this gun a thorough testing.
I will be posting the table top review in a few days with all the specification (Here it is now) but if you're looking for some basic info on the Blackbird you can checkout our online store where you can find some statistics on the Drozd Blackbird and you can also checkout my Drozd Classic Review where I do a short comparison between the Drozd Classic and the newer updated Blackbird version.
I had a lot of fun shooting this gun, it lays down a lot of steel in a very short amount of time and has a virtually endless 900 round BB hopper that just keeps on going. During my testing I shot close to 400 rounds or more using one 88 gram CO2 cartridge and even near the end the Baikal Drozd Blackbird had pretty good feet per second performance.
My Baikal Blackbird does have some upgrades: (JimC Barrel, Full Auto-High RPM Mod Chip, Added Accessory Rails, Red Dot Scope, Tactical Light, Laser and Bulk Air kit) but the stock version is "almost" as fun :)
Thought I would share this photo of a Magazine doubler for his Umarex MP5K PDW one of my viewers (Daniel) sent to me. He lives in the UK and bought his from a supplier out his way. I don't sell them sorry but I have included an Amazon link for my US viewers.
Sometimes you just got to make a video because you can and because it's just plain old fun! And that's why I made this video of me shooting some cans with dual full auto BB machine guns. One is my full auto converted and trusted Cybergun Mini UZI and the other is my newly acquired ZMZ Tyrex PPA-K-01 Russian Machine Pistol.
One of my viewers sent some photos of his custom sanded and polished two-tone ASG STI Duty One 1911. Ken did an awesome job and it makes me want to do the same to mine :)
He started out by sanding off the paint with 500 grit sandpaper and working his way finer right up to 2000 grit and then finishing off with some Meguiar’s NXT Generation metal polish. The results are amazing - see for yourself!
