Lately I have been doing a lot of sourcing out figuring out how everything is going to be laid out, what kind of lighting I want to use, how am I going to heat the office area in my shipping container. I want to keep everything pretty low power so my plan is to go with all LED lighting and a 400 Watt heater which should be

fine in my 90 square foot insulated office space. I plan to blast the shooting range with some propane heat on days when I need it for the shooting testing during the colder months.

I did pickup some hardwood flooring pretty cheap at Big Box Store and also got my 3x6 office window from Surrey New and Used. I already have metal doors that my father-in-law has had stashed away for several decades but at least now they are going to come in handy.

The first job or actual work I needed to do on the Shipping Container Project was to level and place the Sea Can onto some bricks/slabs, this also helps to keep the underside dry so it does not rust out. There shouldn't be much settling since the storage container is resting on my gravel parking area and the gravel goes right down about 1 foot deep to the hard pan.

Next on my list is starting the framing, figuring out exactly where the windows and doors will be and of course cutting the container to fit them.

This Vimeo video will be a little different than most, sorry no shooting and not even a single gun to show anywhere in this video! But it will lead to hopefully better shooting field test and table top videos down the road as I will have a dedicated space not only to work but to also shoot my review airguns.

Today, well actually yesterday a 40 foot shipping container (Sea Can) showed up at my house. This new metal box is going to be my airgun shooting range and office space combined. It will contain a 30 foot airgun shooting range closest to the rear doors so that I can open them and create a longer range if necessary. The front 10-12 feet of the container will be my work office space where. I will also use some of the container for storage.

Over the next few weeks I will be leveling the container, framing and insulating the office area, adding some electricity and lighting and of course completing some finishing work to the office space to make it more cozy. Eventually I hope to do some outside work giving the container some more curb appeal with a new coat of paint.

I plan to make more videos to share with everyone of the work progress as it happens so keep watching...

This year at SHOT Show 2017 in Las Vegas, I found there wasn’t a lot of new Airgun products but as always there are some that stood out for me. If you want more info on each Airgun Company then make sure to watch my full interviews for this years SHOT Show 2017. So without prolonging this video any longer let’s get right into it…

Umarex Legends MP CO2 Full Auto German MP40 Replica Machine-gun:

What’s not to like about the Umarex Legends MP? It has lots of metal parts weighing in at 7.7 pounds, a 60 round steel BB magazine with a dual 12 gram CO2 system. You also get your choice of shooting either in semi auto or full auto at up to 400 fps. Personally the Umarex Legends MP was the most interesting Airgun at the show this year for me and I really think it is going to be a hit!

Umarex SA10 Blowback Pellet and BB CO2 Pistol:

Another interesting product from Umarex this year was the SA10, I am not really sure what it is exactly styled after, it’s more of a futuristic looking gun with slide venting and a thread barrel for adding a mock suppressor or compensator. What appealed to me most about the Umarex SA10 was the new magazine design that incorporates a full size drop out metal magazine with 4 rotary 8 round magazines that can be loaded with either pellets or BB’s. When you empty one 8 shot magazine you simply drop the entire mag out and swap your empty 8 shot rotary magazine for a full one. The SA10 has a nice weight of around 2 pounds and shoots up to 426 fps.

Sig Sauer ASP P320 CO2 Blowback Pellet Pistol:

Sig Sauer introduced their new Sig Sauer ASP P320 CO2 Pellet Pistol this year that will be replacing the P250. Like the P250 the Sig P320 has a metal slide and polymer frame but instead of a double sided 16 shot rotary magazine, the Sig ASP P320 has a newly designed and very unique 30 round belt fed magazine. That’s nearly double the capacity without having to flip the magazine around part way through shooting. It’s great to see innovations like this happening in the airgun market.

Crosman Remington 1875 Shell Loading CO2 Pellet and BB Revolver:

Crosman introduced their own Single Action Old West Revolver this year in the form of the Remington 1875. Like the super popular Umarex Single Action Army Revolvers, the Remington 1875 is also shell loading and uses 12 gram CO2. You have the option of shooting either Pellets or BB’s out of its smooth bore barrel. I expect the Crosman Remington 1875 Shell Loading Revolver to be another popular Old West Airgun Revolver.

Crosman PSM45 Single Shot Spring Powered BB Pistol:

The Crosman PSM45 at first glance may not seem that interesting, after all it’s all plastic on the outside and only shoots about 200 fps! On the plus side it kind of looks like a Glock and we all know how hard it is to find airguns these days that resemble a Glock. I also like the fact that there is no need for any CO2, and most springers out there look like springers while the Crosman PSM45 looks like a real semi auto pistol. The PSM45 even has pretty decent weight to it since there are lots of internal metal parts and a full size drop out metal magazine which was a real surprise in such an entry level low cost pistol. If you’re looking for a fun inexpensive replica plinker than the Crosman PSM45 should fit the bill. On a side not the PSM45 would also make a really great low cost prop since the slide does work and it has that full size drop out magazine!

ASG Dan Wesson 715 2.5 and 4 inch Shell Loading CO2 Revolvers:

The ASG Dan Wesson Revolver has always been a popular choice, and then the Dan Wesson 715 came out improving on the design by adding extra weight and smoothing out the mechanics. How do you top that? Well by giving us some more options like barrel lengths. You now have your choice of a 2.5, 4 or 6 inch barrel for the Dan Wesson 715 and of course you will be able to buy your 715 pick in 4.5mm Steel BB, 6mm Plastic Airsoft or .177 Caliber Pellet ammunition versions. My personal choice may be the 4 inch Dan Wesson 715 since it has the addition of an integrated accessory rail machined into the outer barrel for lasers or tach lights.

Gletcher M1944 Mosin Nogant CO2 BB Rifle:

The Gletcher M1944 Mosin Nogant CO2 BB Rifle is not a new replica gun this year but it has been a hard one to get your hands on. In fact up until SHOT Show 2017 I had never seen one in person and so the Gletcher M1944 is new to me. I was very impressed with the quality of the Gletcher M1944 Mosin Nogant, it has a lot of metal parts including the swing out bayonet and even the simulated wood stock looks like real wood. I even had to take a second look and ask before confirming that the stock is in fact plastic on the Gletcher M1944 Mosin Nogant. I am looking forward to reviewing this rifle in the future when I do finally get one!

Of course there where other interesting products at SHOT Show 2017 this year but those are the products that stood out the most for me. Again make sure to watch my full interview videos to find out more about all the new products at this years SHOT Show.

Roses and chocolate are nice, but nothing says "I Love You" like a semi-automatic rifle. This year ditch the dinner reso and take your sweetheart on a romantic airsoft or hunting adventure. Couples who play together stay together, right?! 

• Shop and save in the Canada Replica Airguns Store
• Shop and Save in the US Replica Airguns Store

And finally my last Vimeo video from SHOT Show 2017 in Las Vegas! Sorry there is no Interview this time with KWA but I did talk a lot with the KWA folks over at SHOT Show this year and I even got to test out their Laser Targeting System designed to be used with several specifi KWA guns by laser-ammo.com.

Unfortunately we don't carry the KWA brand in the replica Airguns store, a few models sneak in when being distriubted by another company like ASG in the case of the ASG MP9. I would love to carry KWA Airsoft Products in the future since they really do make very high quality Airsoft guns.

KWA has a great selection of Airsoft pistols and rifles in both Gas Blowback and AEG formats. The quality reminds me of the KJWors Airsoft guns we sell in the Replica Airguns Canada Store, you can really feel the quality when you pick them up and hold them for yourself.

My First SHOT Show 2017 Las Vegas Interview to kick things off! Dani Navickas from Sig Sauer ASP talks with me about three new CO2 blowback air pistols Sig Sauer ASP is introducing this year just in time for spring season.

The Sig Sauer ASP P320 will be replacing last years P250, don't worry the Sig Sauer ASP P226 is not going anywhere! The P320 is a CO2 Blowback Pellet pistol similar to the previous P250 but this new model has a 30 round belt fed magazine rather than a dual sided 16 round rotary magazine. I love that Sig Sauer ASP is coming out with new innovations like this for us Airgun enthusiasts! The Sig Sauer ASP P320 has a metal slide and polymer frame like it's big powder burning brother and throws pellets at around 430 fps average. Don't expect a ton of shots per CO2, you will be lucky to get two magazine out of a single 12 gram CO2 but I am sure the extra power is worth it.

Sig Sauer ASP also introduced this year two new full metal and full blowback CO2 BB firing 1911's that feature a working safety and grip safety along with a true single action trigger. You have your choice of the signatured Max Michel in two tone black and silver or the Spartan in a Gold Brown finish. Both of these guns are based on the same mechanical build but are cosmetically different. I can say they feel really good in the hand and are super solid. There is a bit of a trade off, you do get a bit higher fps (around 410 fps) than some other 1911's at out there but you will have to put up with a stick magazine.

Of course the Sig Sauer ASP MPX and MCX are still going strong alone with the Sig Sauer ASP P266. Make sure to watch my previous Review Video for the Sig Sauer APS MPX and Sig Sauer APS P226.

Enjoy some additional photos along with my Vimeo Sig Sauer SHOT Show 2017 Interview!

Last week I was in Las Vegas to attend this years 2017 SHOT Show. As always I look forward to this event since I not only get to look at all the new Airgun related products, but I also meet with the big Airgun companies and talk face to face with many of the good folks I have been emailing back and forth with.

This first video will hopefully get you excited to watch my upcoming Interview videos I will be making for companies like: Sig Sauer ASP, Umarex, ASG, Crosman and Gletcher. I also have some additional video of the KWA booth where they had a laser sighting system set up for people to test out their Airsoft guns on a simulated targeting system.

For now here are some photos and of course checkout my Preview Teaser Video of SHOT Show 2017 in Las Vegas.

Happy Holidays from everyone here at Replica Airguns! This year we're offering our loyal customers the gift of FREE SHIPPING in both our Canada and US Online Stores. But it all ends Monday night. So as you recover from your food hangover and Die Hard marathon, check out the great guns and accessories available at ReplicaAirguns.ca and ReplicaAirguns.us

Not sure which accessories match your new gun? We're here to help you with that!

I want to wish everyone a Merry Christmas and Happy New Year, if you don't celebrate Christmas then Happy Holidays to you!

Please also be patient with us over in the Replica Airguns Store as this is the busiest time of year in terms of orders. Because of this it does take a little more time to process all the orders we receive. I understand everyone's eagerness to receive their Christmas Replica Airgun Orders and again we are doing our best to get them processed and shipped.

You may feel that the more emails you send us about your order, the quicker we will process your order but in fact all these extra emails just creates more work for us since we need to read them and figure out which emails are for what orders, it can get very confusing :)

Thanks so much for everyone's support and patients through this very busy holiday season!

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

This is the sale you've been waiting for. Our entire store is 10% off. We've got the best BB guns, lasers, holsters and more. And, as always, we offer free shipping when you spend over $225.

Items are going FAST! So hurry in to get a jump on your holiday shopping. Not sure what to buy the gun nut in your life? Contact us today!

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

I wanted to make a quick update video to let everyone know what I will be up to over the next few weeks since it will effect my video production just a little bit, that said I will do my best to keep the videos coming...

If you remember last year around August, I entered a Fitness contest where I competed in Men's Physique. Well I did fairly well and placed 1st in two divisions, Masters and Open. What this means is I am now qualified to compete in my local Provincial Finals this year which is coming up in less than two weeks. The event is called the Vancouver Pro Am and it will be held in Vancouver BC Canada.

To get to the point, my contest prep especially the last couple of week is fairly taxing on me physically and mentally, it also takes up some of my time. So my videos may not be as regular and they may not be as put together since my mind is not working 100% right now due to the lack of food and carbs I am not eating ;) Anyway I will do my best! You can follow my Fitness journey over at www.GetFitOver40.com.

I also talk about two new Sig products I will be picking up next week to review, the Sig Sauer P250 and Sig Sauer P226 CO2 Blowback Pellet Pistols. I hope to at least have a preview video for you later on next week.

Lastly I am working on a couple of Field Test Shooting videos that I have needed to pump out, one is for the ISSC M22 CO2 Blowback BB Pistol and the other is for the Sig Sauer MPX .177 Caliber Pellet Rifle.

Stay posted for all of these upcoming videos...

To celebrate our Canada Victoria Day Long weekend there will be free shipping all long weekend till end of day Monday in our Canada Replica Airguns Store on all Products! Make sure to take advantage of this limited time offer!

I try and make it to my local gun show which is held in Chilliwack BC about this time each year. It is put on by the Historical Arms Collectors Society of BC and there are generally a lot of used long guns (rifles) some pistols, lots of accessories, knives, hunting gear, knick·knacks and even some antique items. I tend to be looking for airguns or blank guns that are rare or a good deal.

This year I came across a few items that caught my eye. The first item was a Daisy replica 4.5mm BB pistol, I am not a big fan of Daisy replica gun in general as they are usually a far cry from the originals but this Daisy Powerline Model 400 was actually a really good copy of a Desert Eagle in size and looks. Sure it had a lot of plastic in it but it was made in Japan and even being around 20 years olds was holding up really well. This Daisy Powerline 400 even had Blowback which back then was not all that common.

The Daisy Powerline 400 BB Desert Eagle has a 20 round removable magazine that fits along the top of the barrel and it has a claimed fps. It is almost all high grade plastic with the exception of the single action only trigger, safety, hammer, barrel and several internal parts.

The next interesting item I found was a little compact 8mm blank shooter originally made in West Germany. So this blank gun is close to 30 years old. The SM Model 110 8mm Blank Pistol kind of reminds me of my EKOL Tuna in terms of size and functionality since both have the same half slide and magazine release system.

The SM Mod 110 8mm Blank Pistol is front venting and pretty much all metal with reinforced steel areas, it has a 5 round single stack magazine and shoots in single action only.

My last purchase for this show was a new item, here in Canada we generally are not allowed much in the way of items specifically labeled for self defense. There are some work arounds for instance we can carry a knife as long as it is not concealed entirely and we only intend to use it as a tool. We can also carry pepper spray again only for use on animals. Generally speaking we have not been allowed stun guns or tasers here in Canada and even importing them can land you in a lot of trouble! Again it seems a work around has been made, as long as the Stun Gun or Taser is at least 480mm in length then it is not considered a concealable weapon and as long as you have it out on display and only intend to use it on animals that may be a threat to you then all is good :)

The Stun Gun I purchased is basically a baton with a flashlight on the front and a 1 million volt taser on the front of it. You have several options with this device if harm is eminent. You can try blinding the threat with the built in flashlight which is not all that powerful but good for finding your way in dark areas, you can give the attacker a whack with the baton baseball bat style and if none of that is working well let em have the 1 million volt sandwich! We should be getting some of these Stun Baton Flashlights in our Canada Replica Airguns Store at some point so stay posted for that item.

In this 2016 SHOT Show Interview I talk with Chip Hunnucutt from Crosman Corporation. Chip was eager to show off Crosman's new Airbow which is a essentially a hybrid PCP Air Rifles combined with a Crossbow. SO take away the bow and replace the power source with a 3000 PSI compressed air system that is capable of shooting standard archery arrows at 450 fps with 160 foot pounds of energy using 375 grain arrows.

The Crosman Airbow on a full 3000 PSI charge can deliver 8 consecutive shots @ the regulated 450 fps. The Airbow also weighs in at 7 pounds and being that it is a Bullpup design it is only 33.5 inches long so nice and compact for an arrow shooter.

Since the power is generated by the PCP compressed air system there is no heavy cocking rope so a simple lift of the ambidextrous cocking bolt is all that is needed to charge the Crosman Airbow. The Airbow also comes standard with a CenterPoint® 6x40 mm scope specially designed with the Airbow in mind.

Since the Crosman Airbow is technically an under 500 fps airgun, it should be considered an uncontrolled firearm here in Canada which means no PAL license will be required to buy and own the Crosman Airbow in Canada. In terms of using the Airbow for hunting as it is not a bow but rather an Airgun, that is yet to be determined here in Canada.

In this 2016 SHOT Show Interview I talk with Bob Li from Action Sport Games. Bob shows me some of the new products this year from ASG. Some of ASG's newer pistols are the Dan Wesson 715, the CZ 75 SP-01 Shadow, the CZ P-09. New to the rifle line is the CZ Bren 80, also a couple of sniper rifles, the M40A5 and M40A3. ASG is also coming out with a an Inferno HPA version of their CZ Scorpion EVO 3A1.

The ASG Dan Wesson 715 has ot me my favorite product from ASG, you need to hold it in your hand to really understand how solid this pistol really is at close to 3 pounds. Everything about it is an improvement over previous Dan Wesson models including the trigger and hammer action, crane setup and the more actuate frame length with the new more compact internal CO2 valve. The ASG Dan Wesson 715 will be shipping in 4.5mm Steel BB, 6mm Plastic Airsoft and .177 caliber pellet versions.

ASG's two new Full blowback CZ 75 SP-01 Shadow, the CZ P-09 pistols should be coming out shortly, both will be available in 4.5mm Steel BB and 6mm Plastic Airsoft. Both pistols feature a metal slide and frame with full size drop out metal magazines and will have CO2 and Green Gas magazine configurations. The CZ P-09 will have a threaded barrel and barrel protector.