I've already done Table Top Video Review for both the ASG CZ Scorpion VZ61 and the ASG B&T BT5 AEG 6mm Airsoft Guns so make sure to checkout both those videos.

What I hav not done so far is make a Filed Test Shooting video for either gun since this winter has been rather brutal here in BC Canada. Today I did manage to get outside and put some rounds through both the ASG CZ Scorpion VZ61 and the ASG B&T BT5 AEG 6mm Airsoft Guns so at least I can report back to everyone on how they performed for me. Sorry still no actual shooting video as my outside time was kind of limited due to it still being cold, we are even expecting some more snow tonight and over the next few days and it's March!

Getting back to my preliminary shooting testing, the ASG CZ Scorpion VZ61 only shot a slight bit higher then 250 but it was the more accurate of the two AEG Airsoft Guns getting close to a 1 inch 10 shot grouping using my standard 30 foot back semi rested shooting position. It did shoot a bit low but perhaps  a hop-up adjustment should fix that problem.

Next up I tested out the ASG B&T BT5 MP5 PDW Replica and it did have a little more power hitting closer to 300 fps but it was not as accurate as the CZ shooting a bit high and to the left with most shots within about 1.5 inches, still pretty decent from 30 feet back.

Overall both AEG Airsoft Guns where fun to shoot and when I did let them lose to shoot in full auto mode they performed as expected laying down a stream of Airsoft BB's till the mags where empty :)

Distributer: RWA (Made in Hong Kong)

Model: Interdynamic KG-9

Materials: Steel, aluminum and plastic (polymer) construction.

Weight: 3.22 pounds (1460 grams).

Length: 15.7 inches (398mm).

Propulsion: AEG.

Action: Full auto only.

Ammunition Type: 6mm Airsoft BB's

Ammunition Capacity: 90 round magazines (Comes with 2).

FPS: 360+.

Trigger Pull: The trigger pull on the RWA KG-9 AEG Airsoft Machine Pistol is what you would expect form an AEG pistol as it is basically an on/off switch. Since the RWA KG-9 AEG Airsoft Machine Pistol is full auto only it is not easy to shoot a single shot, it can be done with a very short trigger pull but even then you get the occasional multiple shot. The RWA KG-9 AEG Airsoft Machine Pistol like the real steel original version is full auto only and that's what makes it so fun!

Accuracy: I did get a chance to take the RWA KG-9 AEG Airsoft Machine Pistol outside and put some rounds through my Chronograph and down range at a paper target. I averaged just under 340 fps using .20 gram 6mm Airsoft BB's which is about perfect for this compact machine pistol. I also placed about 10 rounds down range 30 feet back using my standard semi rested shooting position while trying to shoot in semi auto and got a pretty decent 1.5 to 2 inch grouping that was a little high but well centered left to right. Elevation could be adjusted using the hop-up.

Build Quality: The RWA KG-9 AEG Airsoft Machine Pistol is really one of the best made Airsoft guns I have seen in a while, all the metal parst are going to be real steel or aluminum, not your standard zinc alloy found in most airguns these days. The full upper is stamped steel along with the 90 round magazines, the lower is plastic with a few aluminum parts here and there. The fit and finish is also excellent!

Realism: The RWA KG-9 AEG Airsoft Machine Pistol is a replica of the Swedish made Interdynamic KG9 Open Bolt SMP, not the ntratec Tec-9 which was the American version of the KG9. For the most part the RWA Airsoft version is exact with the exception of the barrel shroud being slightly longer to accommodate the 7.4v LiPo batteries.

Pros:

• Lots of steel in this gun including full upper, barrel, pins and magazines.

• Very high quality build with a solid weight and excellent fit and finish.

• Fairly high rate full auto fire.

• Comes with battery and two magazines.

• Has almost perfect usable working rate of fire averaging around 340 fps with decent overall accuracy.

• Working cocking handle.

• Fully Licensed.

Cons:

• No blowback but there is some recoil feel from the heavy spring action.

• No semi auto mode, full auto only.

• Sights are not adjustable, can only use hop-up to adjust elevation.

• Limited on battery choices.

Comments:

The RWA KG-9 AEG Airsoft Machine Pistol is a really cool looking Airsoft gun, it is a bit larger than most hand guns but could still be used like one since it does not have a stock and can be used for similar shooting situations. The advantage is you have 90 rounds of full auto ammo at your disposal in a size format that is super compact and easy to manoeuvre. You also get some pretty decent power for longer range shooting and the accuracy out of the box at a variety of ranges is also really good. You could even use the RWA KG-9 AEG Airsoft Machine Pistol easily as a primary or even kick ass backup gun as it is super versatile.

Watch my Vimeo Table Top Review of the RWA KG-9 AEG Airsoft Machine Pistol:

This year at SHOT Show 2017 in Las Vegas, I found there wasn’t a lot of new Airgun products but as always there are some that stood out for me. If you want more info on each Airgun Company then make sure to watch my full interviews for this years SHOT Show 2017. So without prolonging this video any longer let’s get right into it…

Umarex Legends MP CO2 Full Auto German MP40 Replica Machine-gun:

What’s not to like about the Umarex Legends MP? It has lots of metal parts weighing in at 7.7 pounds, a 60 round steel BB magazine with a dual 12 gram CO2 system. You also get your choice of shooting either in semi auto or full auto at up to 400 fps. Personally the Umarex Legends MP was the most interesting Airgun at the show this year for me and I really think it is going to be a hit!

Umarex SA10 Blowback Pellet and BB CO2 Pistol:

Another interesting product from Umarex this year was the SA10, I am not really sure what it is exactly styled after, it’s more of a futuristic looking gun with slide venting and a thread barrel for adding a mock suppressor or compensator. What appealed to me most about the Umarex SA10 was the new magazine design that incorporates a full size drop out metal magazine with 4 rotary 8 round magazines that can be loaded with either pellets or BB’s. When you empty one 8 shot magazine you simply drop the entire mag out and swap your empty 8 shot rotary magazine for a full one. The SA10 has a nice weight of around 2 pounds and shoots up to 426 fps.

Sig Sauer ASP P320 CO2 Blowback Pellet Pistol:

Sig Sauer introduced their new Sig Sauer ASP P320 CO2 Pellet Pistol this year that will be replacing the P250. Like the P250 the Sig P320 has a metal slide and polymer frame but instead of a double sided 16 shot rotary magazine, the Sig ASP P320 has a newly designed and very unique 30 round belt fed magazine. That’s nearly double the capacity without having to flip the magazine around part way through shooting. It’s great to see innovations like this happening in the airgun market.

Crosman Remington 1875 Shell Loading CO2 Pellet and BB Revolver:

Crosman introduced their own Single Action Old West Revolver this year in the form of the Remington 1875. Like the super popular Umarex Single Action Army Revolvers, the Remington 1875 is also shell loading and uses 12 gram CO2. You have the option of shooting either Pellets or BB’s out of its smooth bore barrel. I expect the Crosman Remington 1875 Shell Loading Revolver to be another popular Old West Airgun Revolver.

Crosman PSM45 Single Shot Spring Powered BB Pistol:

The Crosman PSM45 at first glance may not seem that interesting, after all it’s all plastic on the outside and only shoots about 200 fps! On the plus side it kind of looks like a Glock and we all know how hard it is to find airguns these days that resemble a Glock. I also like the fact that there is no need for any CO2, and most springers out there look like springers while the Crosman PSM45 looks like a real semi auto pistol. The PSM45 even has pretty decent weight to it since there are lots of internal metal parts and a full size drop out metal magazine which was a real surprise in such an entry level low cost pistol. If you’re looking for a fun inexpensive replica plinker than the Crosman PSM45 should fit the bill. On a side not the PSM45 would also make a really great low cost prop since the slide does work and it has that full size drop out magazine!

ASG Dan Wesson 715 2.5 and 4 inch Shell Loading CO2 Revolvers:

The ASG Dan Wesson Revolver has always been a popular choice, and then the Dan Wesson 715 came out improving on the design by adding extra weight and smoothing out the mechanics. How do you top that? Well by giving us some more options like barrel lengths. You now have your choice of a 2.5, 4 or 6 inch barrel for the Dan Wesson 715 and of course you will be able to buy your 715 pick in 4.5mm Steel BB, 6mm Plastic Airsoft or .177 Caliber Pellet ammunition versions. My personal choice may be the 4 inch Dan Wesson 715 since it has the addition of an integrated accessory rail machined into the outer barrel for lasers or tach lights.

Gletcher M1944 Mosin Nogant CO2 BB Rifle:

The Gletcher M1944 Mosin Nogant CO2 BB Rifle is not a new replica gun this year but it has been a hard one to get your hands on. In fact up until SHOT Show 2017 I had never seen one in person and so the Gletcher M1944 is new to me. I was very impressed with the quality of the Gletcher M1944 Mosin Nogant, it has a lot of metal parts including the swing out bayonet and even the simulated wood stock looks like real wood. I even had to take a second look and ask before confirming that the stock is in fact plastic on the Gletcher M1944 Mosin Nogant. I am looking forward to reviewing this rifle in the future when I do finally get one!

Of course there where other interesting products at SHOT Show 2017 this year but those are the products that stood out the most for me. Again make sure to watch my full interview videos to find out more about all the new products at this years SHOT Show.

And finally my last Vimeo video from SHOT Show 2017 in Las Vegas! Sorry there is no Interview this time with KWA but I did talk a lot with the KWA folks over at SHOT Show this year and I even got to test out their Laser Targeting System designed to be used with several specifi KWA guns by laser-ammo.com.

Unfortunately we don't carry the KWA brand in the replica Airguns store, a few models sneak in when being distriubted by another company like ASG in the case of the ASG MP9. I would love to carry KWA Airsoft Products in the future since they really do make very high quality Airsoft guns.

KWA has a great selection of Airsoft pistols and rifles in both Gas Blowback and AEG formats. The quality reminds me of the KJWors Airsoft guns we sell in the Replica Airguns Canada Store, you can really feel the quality when you pick them up and hold them for yourself.

Enjoy my latest SHOT Show Interview with Jesse Caster from Crosman. Jesse shows me Crosman’s latest old west single action revolver, the Remington 1875 which shares a lot with the super popular Colt Single Action Army revolvers. Jesse also goes over some new airgun pistols with me, a CO2 powered non blowback 1 to 1 replica of the Remington RP45, a very interesting single shot spring piston “Glock-ish looking pistol called the PSM45. And last but not least, Crosman has now got on the Beretta / Taurus bandwagon and added the PFAM98 to their lineup.

Crosman’s new Remington 1875 should be a welcome addition for anyone looking to add something new to their Old West Airgun lineup. The Crosman Remington 1875 like the Colt Single Action Army Revolver is shell loading, shoots in single action only and has that super slick ratcheting cylinder we all love. The Crosman Remington 1875 shoots both .177 caliber pellets and 4.5 mm steel BB’s from its smooth bore barrel, but Jesse has gone on record to claim that the pellets work well and shoots pellets and BB’s accurately at ranges typical for this type of Airgun.

Another Remington Licensed Airgun from Crosman this year is the Remington PR45. The PR45 is a 1 to 1 replica of the real steal Remington RP45 but in a CO2 non-blowback 4.5mm BB shooting version. The Crosman PR45 has a metal slide and polymer frame with a drop out all metal stick magazine. Some other notable features for the Crosman PR45 are a working trigger safety and white dot sights front and back.

If you are looking for something a little different from Crosman this year then checkout the single shot spring piston PSM45. This super affordable air pistol kind of looks "similar" to a Glock and lord knows how many times I get asked what is available in an airgun that resembles a Glock. The Crosman PSM45 is not going to win any fps awards (shoots around 200 fps), but there is no need to buy any CO2 and you can shoot this airgun in virtually any temperature for only the cost of steel BB’s. The frame and slide on the Crosman PSM45 are plastic but it does have decent weight do some internal metal parts and an unexpected full metal full size drop out magazine.

Crosman this year is adding a Beretta/Taurus full metal and full blowback CO2 BB Pistol to their product lineup. You may have already guessed it, it’s essentially a KWC Beretta / Taurus which really isn’t a bad thing since the KWC Blowback Beretta / Taurus has been very popular with replica airguners. A nice little treat with the Crosman PFAM98 Beretta / Taurus is that right out of the box it shoots in both semi and full auto using the ambidextrous selector safety switch.

This Vimeo Unboxing Preview Video focuses on two AR M4 styled AEG Airsoft Rifles. The G&G CM16 Rifles are all pretty much the same other than the barrel lengths and come in the following versions, the CM16 SRS, CM16 SRL and CM16 SRXL. I also showcase the Umarex HK M27 which is distributed by Umarex but made by VFC which is knwo for their high quality products. I will be following up this Preview Unboxing Video with individual more detailed Review videos for each AEG AR M4 rifle.

G&G CM16 SRS Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: G&G Armament

• Model: CM16 SRS

• Materials: Metal and Polymer Construction

• Weight: 4.97 Pounds

• Barrel:  8.1 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto, 3-Round Burst Modes

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 300 rounds

• FPS: 420 fps

Buy G&G CM16 SRL Black AEG Airsoft Rifle in Canada

G&G CM16 SRL Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: G&G Armament

• Model: CM16 SRS

• Materials: Metal and Polymer Construction

• Weight: 5.1 Pounds

• Barrel:  10.2 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto, 3-Round Burst Modes

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 300 rounds

• FPS: 420+ fps

Buy G&G CM16 SRL Black AEG Airsoft Rifle in Canada

G&G CM16 SRXL Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: G&G Armament

• Model: CM16 SRS

• Materials: Metal and Polymer Construction

• Weight: 5.24 Pounds

• Barrel:  13 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto, 3-Round Burst Modes

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 300 rounds

• FPS: 420+ fps

Buy G&G CM16 SRXL Black AEG Airsoft Rifle in Canada

Umarex H&K M27 Black AEG Airsoft Rifle

• Type: Airsoft Rifle

• Manufacturer: Umarex VFC

• Model: H&K M27

• Materials: Metal and Polymer Construction

• Weight: 6.7 Pounds

• Barrel:  14.2 inches

• Propulsion: Electric AEG

• Action:  Semi, Full Auto

• Ammunition Type: 6mm Plastic Airsoft BBs

• Ammunition Capacity: 320 rounds

• FPS: 400 fps

Buy Umarex H&K M27 Black AEG Airsoft Rifle In Canada

Buy Umarex H&K M27 Black AEG Airsoft Rifle in the US

This Unboxing Preview Video focuses on three Bullpup designed AEG Airsoft Rifles. The two Steyr Aug Bullpups are distributed through ASG while the IWI Tavor 21 is distributed via Umarex. In this Unboxing Preveiw video I take each gun out of the box and go over some basic specification and show you around each AEG Bullpup Rifle a little bit. I will be following up this Preview Unboxing Video with individual more detailed Review videos for each AEG rifle.

Here are some of the basic Specifications for each AEG Airsoft Rifle.

AEG Steyr AUG A3 MP AEG Aisoft Bullpup Rifle

• Type: Airsoft Bullpup Rifle

• Manufacturer: ASG

• Model: Steyr AUG A3 MP

• Materials: Metal and Polymer

• Weight: 3.85 kg (8.5 pounds) 

• Barrel: 21.2 mm (0.83 inches)

• Power Source: Electric AEG

• Action: Semi & Full Automatic

• Ammo Type: 6mm Plastic Airsoft BBs

• Ammo Capacity: 300 rounds

• FPS: 394

Buy AEG Steyr AUG A3 MP AEG Airsoft Bullpup Rifle in Canada

Buy AEG Steyr AUG A3 MP AEG Airsoft Bullpup Rifle in the US

ASG Steyr AUG A2 Tan AEG Rifle

• Type: Airsoft Bullpup Rifle

• Manufacturer: ASG

• Model: Steyr AUG

• Materials: Polymer with Metal Internals

• Weight: 3.39 kg (7.5 pounds)

• Length: 805 mm (31.7 inches)

• Power Source: Electric AEG

• Action: Semi & Full Automatic

• Ammo Type: 6mm Airsoft BBs

• Ammo Capacity: 300 rounds

• FPS: 394

Buy ASG Steyr AUG A2 Tan AEG Airsoft Bullpup Rifle in Canada

Umarex IWI Elite Tavor 21 Airsoft AEG Bullpup Rifle

• Type: Airsoft Bullpup Rifle

• Manufacturer: Umarex

• Model: Steyr AUG

• Materials: Polymer with Metal Internals

• Weight: 3.5 kg (7.71 pounds)

• Length: 755 mm (29.7 inches)

• Power Source: Electric AEG

• Action: Semi & Full Automatic

• Ammo Type: 6mm Airsoft BBs

• Ammo Capacity: 300 rounds

• FPS: 395

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Power Sources Covered in this review: CO2 - Green Gas / Propane - Spring - AEG / AEP (Automatic Electric Gun - Airsoft Electric Pistol)

Pro’s:

• CO2 Airsoft Guns allow for fast repeat shooting, great for action shooters, generally CO2 Airsoft Guns will have a little more power then Green Gas Airsoft Guns. There is no need to pump or cock your CO2 powered Airsoft gun in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting. 

• Green Gas (Propane) Airsoft Guns operate much the same as CO2 Airsoft guns so they all make for great action shooters and the Green Gas powers the mechanical operation allowing for very realistic operation. Green Gas (Propane) Airsoft Guns can cost a little bit less to operate that a CO2 Airsoft Gun especially if you plan to use Propane as it can be cheaper to buy than the smaller 12 gram CO2 Cartridges.

• Spring Airsoft Guns are generally fairly basic and low cost so they are the usually the most affordable Airsoft guns to buy. There is no need to buy CO2 or Green Gas or even a Battery and Charger Setup so the cost to shoot Spring Airsoft Guns is only going to be subject to the Airsoft BB’s you plan on buying.

• AEG (Automatic Electric Guns) have the most consistent power as they use a spring internally that the electric motor draws back before each shot, the internal spring will essentially apply the same force to the Airsoft BB’s with each shot. AEG (Automatic Electric Guns) are a great option when you are wanting a Full Auto Airsoft gun since there is no cool down effect and as long as your batteries are charged and you have Airsoft BB’s in your magazine, the gun will simply keep shooting. AEG (Automatic Electric Guns) allow for the highest capacity magazines and often hold as many as 500 Airsoft BB’s in a single magazine. So if you’re looking for raw firepower an AEG or AEP Airsoft Gun is your best option. Once you have purchased your AEG (Automatic Electric Gun) and a battery and charger setup, they are fairly inexpensive to operate since no CO2 or Green Gas is required.

Con’s:

• CO2 Airsoft Guns require the additional cost to buy the CO2 cartridges as they will not function without it. CO2 Airsoft Guns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airsoft Guns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments. CO2 Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up the magazine and even the gun.  

• Again since Green Gas (Propane) Airsoft Guns work much like CO2 Airsoft Guns, they are effected by cool down and lose power when shoot quickly or as the Green Gas or Propane runs low. Green Gas does not expand as much as CO2 so it will not be as powerful and even less effective in colder temperatures. Green Gas Airsoft Guns will have a more conservative ammunition capacity since too high of a capacity magazine would freeze up.

• Spring Airsoft Guns are not the best action shooters since you need to manually operate the slide to pullback the spring prior to each shot, this does work well with Pump, Lever and Bolt Action Airsoft guns but is not the best option for pistols since most real steel pistols operate in semi auto mode.

• If you plan to use your AEG (Automatic Electric Gun) in a battle then it will require a multi battery setup which does cost a bit more upfront. AEG (Automatic Electric Guns) are know to not operate as realistically as a CO2 or Green Gas Airsoft gun since CO2 and Green Gas Guns do allow for the same realistic mechanical operation which can give very believable blowback operation, this is hard to replica with an AEG Airsoft Gun.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

First off I want to point out that both of these guns I have already reviewed in slightly different cosmetic versions. The Umarex Beretta M92 A1 Desert Storm is essentially the same gun as the Umarex Beretta Mod. 92 A1 Blowback CO2 BB Pistol but with a distressed aged look and the Commemorative Desert Storm licensing on it. Similarly the Daisy Powerline Tactical 5502 CO2 Blowback BB Pistol is based on the chrome framed Daisy Powerline 5501 but the Daisy Powerline 5502 comes with a sight rail and compensator.

Check out my other reviews for the Daisy Powerline 5501 and Umarex Mod. 92 A1.

In this video I show you around both the Umarex Beretta M92 A1 Desert Storm and Daisy Powerline Tactical 5502 CO2 Blowback BB Pistol and compare them to their significant similar versions. I talk a bit about specifications but this is a preview video so I don't go into full details. I hope to add some follow up reviews especially a comparison shooting video between the Daisy Powerline Tactical 5502 and Daisy Powerline 5501 since there is a barrel length difference that may give the Powerline 5502 an FPS performance advantage.

I will leave you now with some specifications for both guns.

Umarex Beretta Desert Storm Commemorative Blowback CO2 BB Pistol

• 12 gram CO2 with Blowback

• 4.5mm Steel BB's

• 18 shot magazine

• Smooth Bore Barrel

• Single & Double Action

• Semi & Full Auto Selectable

• 310 fps

• 2.4 Pounds

Buy Umarex Beretta Desert Storm Blowback CO2 BB Pistol in Canada

Buy Umarex Beretta Desert Storm Blowback CO2 BB Pistol in the US
 

Daisy Powerline 5502 Tactical CO2 Blowback BB Pistol

• 12 gram CO2 with Blowback

• 4.5mm Steel BB's

• 15 shot magazine

• Smooth Bore Barrel

• Single Action Only

• Semi Auto

• 480 fps

• 1.66 Pounds

Buy Daisy Powerline 5502 Tactical CO2 Blowback BB Pistol in Canada

Buy Daisy Powerline 5502 Tactical CO2 Blowback BB Pistol in the US

Watch and see what happens when you take an RWA M1919 AEG Airsoft Machine Gun and put it head to head against the all metal F1 Chrony Chronograph. That's right, my old temperamental Chrony F-1 Chronograph meets its first opponent! Did it survive or did it bow to the hail storm of 6mm Airsoft BB's...

Video number three in my Summer Full Auto Fun Video Series! In this outside shooting test I take out my Cybergun KWC Desert Eagle .50AE CO2 Airsoft Pistol and shoot it in full auto mode again at some water filled pop cans and clay pigeons setup about 25 feet down range.

Since I pretty much took my Cybergun KWC Desert Eagle .50AE CO2 Airsoft Pistol right out of the box and started shooting I did not have the chance to set the hop-up or even figure out exactly where it was shooting and as I found out it was shooting rather high and the .20 gram BB's may have been a bit light since they seemed to spray all over. Either way I did manage to hit a few targets after eating up all the CO2 and shooting off two full mags of Airsoft Ammo...

Buy the KWC Desert Eagle in Canada

 Buy the Cybergun Desert Eagle in Canada

Buy the Cybergun Desert Eagle in the US

Here is my second instalment for this summers Full Auto Fun Videos. in this Full Auto Fun Video I shoot my KWC M712 Broomhandle CO2 BB Pistol at some more water filled Pop Cans and Clay Pigeons in Full Auto mode of course :)

Make sure to watch my other KWC M712 Broomhandle CO2 BB and Airsoft Pistol videos and keep in mind we sell both the 4.5mm Steel BB version and 6mm Airsoft Version in our Canada Replica Airgun Store.

Buy the KWC 4.5mm BB

Buy the KWC 6mm BB

Last summer I made some "Full Auto Fun" videos and well... I had a lot of fun making them and of course shooting the full auto airguns. So I got to thinking I should make some more Full Auto Fun videos again this summer, at least for some of the new Full Auto guns I have not made these videos for yet.

So to kick it off, I brought out my Umarex Beretta Mod. 92 A1 CO2 BB Pistol and shot up some clay pigeons and water filled cans in Full Auto Mode of course :)

Buy the Umarex Beretta M9 A1 BB Pistol in Canada

Buy the Umarex Beretta M9 A1 BB Pistol in the US

I have already done my full Table top Review for the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol so make sure to check that review out for more details on specifications and features.

In this Field Test Shooting video I take out my Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol and place five shots through my Chrony Chronograph to find out what the real word velocity performance will be and I also test the accuracy of the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol by shooting ten rounds down range at a paper target from 30 feet back using a semi rested shooting position(Gun rested on a sandbag, standing in the back). I also include some slow motion video of the Umarex Beretta Mod. 92 A1 blowback action close up in both semi auto and full auto modes.

For the Feet Per Second portion of my test I used a brand new CO2 along with 5.1 grain RWS nickel coated 4.5mm Steel BB's. The temperature outside was 15 degrees Celsius (59 Fahrenheit), so not super warm or cold, I would expect a little higher fps on a warmed day. Umarex claims a velocity of 310 fps, I was able to get a five shot average of 322 which was nice to see a higher than claimed fps for the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol.

Moving on to the Accuracy portion of my Field Test, I was able to get all 10 shots within a 2 inch grouping, not bad for a heavy blowback BB pistol. I did notice the shots where a little low and to the right so some shot placement adjustments may be required depending on your shooting range since the sights on the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol are non-adjustable. The blowback action is nice and strong and the trigger is also very typical to what you would find on a Beretta M92. Shooting in full auto mode is a lot of fun and really gets your hand rocking. You should be able to get around 4 magazines in semi auto shooting mode and closer to 3 magazine in full auto shooting mode.

I really like the Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol from Umarex, it's what many of us have been waiting for, a true licensed Model 92 and to top it off we even got full auto thrown in for fun :)

Buy the Umarex Beretta M9 A1 BB Pistol in Canada

Buy the Umarex Beretta M9 A1 BB Pistol in the US

Type: BB air pistol.

Distributer: Umarex.

Model:Beretta Mod. 92 A1.

Materials: Pretty much all metal build.

Weight: 2.4 pounds (1100 grams).

Barrel: 4.38 inchesBrass, non-rifled.

Propulsion: CO2 x1.

Action: Semi and full auto blowback, single and double action.

Ammunition Type: 4.5mm Steel BB's.

Ammunition Capacity: 18 rounds.

FPS: 310.

Trigger Pull: The trigger pull on the Umarex Beretta Mod. 92 A1 BB Pistol is like what you would expect from a real Beretta 92 A1, it offers both single and double action but most of the time you will be shooting in single action since the blowback cocks the hammer after each shot. Single action has a little bit of take-up but has a predictable release that is not overly light or heavy. Double action shots are longer and heavier which is as expected.

Accuracy: I have not shot this "version" of the Umarex Beretta Mod. 92 A1 but it will undoubtedly perform very similar to the many other full blowback CO2 pistols I have tested like the KWC and Cybgergun M92's, 1911's and Sigs. I did notice the slide spring on the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol to be very firm so I am expecting it to have pretty good blowback action. One other consideration is this CO2 airguns offers both semi and full auto shooting options but with the heavy blowback, don't expect much accuracy when shooting in full auto mode :)

Build Quality: Very good, with almost all metal construction, good weight and craftsmanship. Don't quote me on this but I have a feeling the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol may be made by KWC, if this is the case then we know to expect the same quality as we have found with other KWC full blowback airguns which is pretty good overall. There may be some wear in the high spots of the finish over time but I kind of like this since it gives the gun a more realistic look.

Realism: This is by far the closest Beretta Model 92 out there, even the magazine butt plate looks the part, the safety is true to form and it is full licensed and trademarked throughout the gun via Umarex. I'm not sure if the real steal Umarex ever offered full auto or not but we can look past this for the sake of how much fun it is going to be shooting in full auto! The only negative aspect in terms of realism is the white warning writing on the left side of the slide.

Available at the:Replica Airguns Store

Pros:

• Your choice of shooting in either semi auto or full auto mode.

• Really nice replica of the original Beretta 92 A1.

• Great weight and feel to it.

• All metal design, fit and finish is very good.

• Strong slide spring so it should have heavy blowback action.

• Realistic working safety and working slide catch and release.

• Full size dropout metal magazine that holds BB's and CO2.

• Can be field stripped like original Beretta 92 A1.

• Fully Beretta licensed.

Cons:

• Will probably eat CO2 especially in full auto mode.

• Non-adjustable sights.

• Ugly white warning instruction on the slide.

Comments:

I know the KWC M92 and Cybergun GSG 92 have been out for a while and the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol is along the same lines, but I do like that it is a true Beretta Replica rather than the Taurus copy. I like that Umarex went the extra mile and made the magazine look the part with a much shorter butt plate and adding semi and full auto right out of the box with a dedicated selector switch is pretty cool too. I am really looking forward to testing this gun out and seeing how the blowback action combined with the full auto ability is going to recoil, I have a feeling it's going to kick like a mule!

My Vimeo Videos for the Umarex Beretta Mod. 92 A1 CO2 Blowback 4.5mm BB Pistol:

Buy the Umarex Beretta M9 A1 BB Pistol in Canada

Buy the Umarex Beretta M9 A1 BB Pistol in the US