Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.
For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.
For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.
The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball pistol, it has a very different look and also uses .50 caliber Paintballs which are a little bit less common than the .68 and .43 caliber paintball gun I have been reviewing up until now. The Umarex T4E TR50 .50 Caliber Paintball Revolver is some countries is marketed as a self defense gun but those versions do have a little bit more fps and foot pounds of energy. The version I am testing is not marketed here in Canada or the US as self defense products but rather as more of a training Paintball Gun.
Starting with my Chronograph velocity test I placed 5 Rubber Balls through my Chronograph using a brand new CO2. The Rubber balls I am going to say are a little bit heavier than standard Paintballs and Umarex claims the Umarex T4E TR50 .50 Caliber Paintball Revolver is capable of hitting around 360 fps so with the heavier rubber balls I was expecting a little bit under the max fps. I was able to get an average of 328 fps so not bad at all.
Moving on to my accuracy test. I need up placing 10 of my 12 rounds into the paper target as I had two rounds that went off in what I am going to call an uncontrolled manor. The 10 rubber paintball rounds that did hit my paper target that was setup 30 feet down range all hit within about 6 inches of each other daily well centered left and right and a little bit low on the target. Gettin back to the uncontrolled shots, I had a situation where I pulled the trigger and the Umarex T4E TR50 .50 Caliber Paintball Revolver went click as you would expect but no CO2 was expelled and so no round was shot. I thought perhaps the cylinder was caught up so I went to wiggle it to try and free it up. As I did so the gun went off without my finger anywhere near the trigger. I am glad I was using rubber balls since the rubber ball hit my cabinet leaning a biota a mark but really causing any damage. This happened twice with the same cylinder, the second time I was bit more prepared for it and had the gun pointed well downrange. I was not able to recreate this problem again so perhaps the cylinder magazine was not seated properly but this still concerns me a bit.
Overall I really like the Umarex T4E TR50 .50 Caliber Paintball Revolver, it’s a pretty cool looking Paintball Gun with decent accuracy and power, you can even feel a little push back and barrel lift when you shoot it. I also like that you can preload a CO2 and puncture it whenever hypo are ready to shoot with a quick smack on the bottom of the grip. Just made sure to put the CO2 in the right way :)
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
This isn’t a SHOT Show 2020 Interview but most certainly worth reporting on. While walking around SHOT Show I ventured into the Chiappa Booth as I own a .22 caliber 1911 styled pistol from them and they do have some interesting products to take a look at.
Then I saw a red tip on one of their Chiappa Rhino Revolvers which caught my eye since I was not aware that Chiappa was making an Airgun version of their Rhino. Well as it turns out they are hoping to be shipping both an Airsoft version and Steel BB version around spring time and from what I can tell there will be two finishes, a kind of Gold Satin finish and also a Back finish version. As is with a lot of revolvers these days they will be shell loading which will help them look the part of a real steel Chiappa Rhino Revolver.
Looking forward to getting my hands on one when they come out in Spring this year!
Here we go again, another round of SHOT Show videos brought to you direct from Replica Airguns!
As always I like to start off with a Teaser Video with a few quick clips of some of the new products I had the opportunity to take a look at at this years SHOT Show 2020 Las Vegas.
I will be rolling out Interview Videos as quickly as I can edit them and put them together for the following Airgun Related companies:
Sig Sauer
Umarex
Crosman - Velocity Outdoors
ASG
Air Venturi
Chiappa
So sit back and enjoy this years Replica Airguns SHOT Show 2020 Las Vegas Teaser Video!
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:T4E TR50 Materials: Metal & Polymer. Weight: 726 grams (1.6 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Revolver - Double action only trigger. Ammo Type: .50 Caliber Paintball or Rubber Ball. Ammo Capacity: 6 Rounds x 5 magazines. FPS: 360.
Trigger Pull: The trigger pull on Umarex T4E TR50 .50 Caliber Paintball Revolver is double action only but not very long with a very different feel than I am use to. The best way to describe it is kind of lumpy, it starts out a bit firm and then eases off a lot just before it releases. Like climbing a hill and then coasting down the otters side. I will have to see how it feels when it’s all loaded up with CO2 and Paintballs and actually shooting at a target.
Build Quality: The build quality of the Umarex T4E TR50 .50 Caliber Paintball Revolver is good overall. It is a mostly plastic build with some metal parts where they need to be internally. It is essentially two plastic halves held together by screws with the few actual mechanical working external parts. You have the trigger with it’s working trigger safety, the removable magazine and magazine release and of course the quick puncture CO2 screw knob. The hammer is internal. The Umarex T4E TR50 .50 Caliber Paintball Revolver is not very heavy but it does feel really solid in the hand.
Expected fairly high fps power of 360 with .50 caliber paintballs, a bit too high for your average paintball field but perhaps powerful enough to discourage an intruder?
Lots of mounting option for accessories like a tac light, laser or other sighting option with it’s upper and lower picatinny rail setup.
Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.
Working Trigger Safety.
Comes with 5 total magazines you can preload ready for use.
Super non-complicated design. Once loaded with CO2 and Paintballs all you need to do is hit the CO2 knob and then pull the trigger.
Build quality feels good, the gun is fairly beefy but not overly heavy or hard to hold.
Cons:
Mostly all plastic build.
Sights do not have white dots on them and are not adjustable.
Do not expect a lot of shots per CO2. Will find out when I do my Field Test Shooting Review.
Comments:
The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball gun, overseas versions are marketed as the HDR50 which stands for “Home Defense Revolver”, while the North American version is marketed as the TR50 or “Training Revolver”. This is mainly because in the Europe most countries are not allowed to own real handguns but can own “Self Defense handguns”. In North America as most people are well aware, in the US real handguns are very easy to obtain and can be used for self defense. Just across the border here in Canada we can not really purposely have on hand anything that we plan to use as a weapon for self defense so the Umarex T4E TR50 .50 Caliber Paintball Revolver is marketed as a Training Revolver. What’s the difference? Not much, our North American 360 fps version is a lot like the 7.5 joule German version in terms of power but you can also get a more powerful 11 joule version in the UK. All that said, the Umarex T4E TR50 .50 Caliber Paintball Revolver at least here in Canada is made and marketed as a Paintball gun but on the field may be too powerful? What you decide to do with it is up to you!
I have not officially done a Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle other than my quick outside shooting test where I simply shot a bunch of rounds at some pop cans just to see how the Umarex Legends CO2 BB Lever Action Cowboy Rifle would work for me and it did perform well during that test.
Jumping ahead to a little while later when I went to make my Official Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle. I found it was not performing well at all, shooting well under the 410 claimed fps closer to 200 fps which was a surprise since it seemed to do a lot better for me on my previous test. I even changed out the CO2 but still did not get any better results. I racked this up to maybe being a defective gun and so I went about getting my hands on another Umarex Legends CO2 BB Lever Action Cowboy Rifle.
Guess what? Same thing with rifle number two. Very poor fps, again almost half of the claimed rated velocity. So at this point I decided I was goring to make the Field Test Shooting Video for the Umarex Legends CO2 BB Lever Action Cowboy Rifle and let the results speak for themselves… I also thought it would be fun to compare it to the Classic 1938 Daisy Red Ryder BB Gun since I figured they would both get similar fps and accuracy and be rather comparable at the end of the day.
I do have to say that the Umarex Legends CO2 BB Lever Action Cowboy Rifle did make me eat my words and I am happy it did since I really like the Umarex Legends CO2 BB Lever Action Cowboy Rifle and wanted it to do well!
Usually I state all there results for My Field Test Shooting Videos here in the written article but I kind of feel it is best if you just watch this one from start to finishes since the video result s did turn out to really surprise me in the end.
We had a lot of great new Airguns that I reviewed this year at Replica Airguns. Some of them really stood out to me and so I made a video showing my Favorite Replica Airgun Picks of 2019. Of course there where many other Airguns that could has just as easily made this video but I had to draw the line somewhere and pick the ones that in my opinion where the best of 2019. Make sure to watch my Vimeo video where I go into some more details on why I liked each Airgun.
Below is a list of the top Replica Airgun Picks of 2019:
Type: Paintball Gun. Manufacturer:Umarex - T4E. Model:S&W M&P9 M2.0 Materials: Metal & Polymer. Weight: 763 grams (1.7 pounds). Barrel: Smooth bore. Power Source: 1x12 gram CO2. Action: Semi-Automatic with blowback action. Ammo Type: .43 Caliber Paintball or Rubber Ball. Ammo Capacity: 8 Rounds. FPS: 290.
Trigger Pull: The trigger pull on Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol feels a lot like a double action trigger mainly because when you pull the trigger the inner barrel travels backwards into the magazine which seals off the barrel form the magazine so less CO2 is wasted going it not the magazine and also placing a paintball round in the barrel. This does make the trigger a little bit longer and heavier than a single action trigger. I believe the internal hammer/striker is engaged from the blowback action.
Build Quality: The build quality of the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is really very good, metal parts are where you would expect them, the slide, slide catch, barrel, magazine and most internal parts giving the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol a nice near 2 pounds (1.7 pounds) of weight with the magazine in which makes the Paintball version a little heavier than the real steal version (1.54 pounds) but once the real steal version is loaded with a full mag this may even out a bit. The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol does have a polymer frame but again this is normal with todays modern guns and helps keep the weight down. Fit and finish is also very good!
Realism: The Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol is a near perfect replica of the real steel S&W M&P9 M2.0 Pistol, from the fully licensed markings to the large .43 caliber diameter barrel. If you placed the Paintball version side by side with the real steel version I doubt you could tell them apart unless you start inspecting it really close up and working the action. You will find that the slide cycle distance is a bit shorter than it would be meaning that when the side catch is engaged the slide does not go as far back as it the real 9mm S&W M&P9 M2.0. Field stripping the Umarex T4E S&W M&P9 M2.0 .43 Cal. Paintball Pistol will requires some tools and pin removal.
Another Field Test Shooting Video Review coming for the Replica Airguns Sea Can Indoor Airgun Shooting Range! In todays Shooting Review I test out the Schofield No. 3 CO2 BB-Pellet Revolver using both 4.5mm 5/1 grain Steel BB’s and .177 Caliber 6.9 grain Lead Pellets to see how well they perform in velocity and accuracy. As always I use a brand new CO2 for my velocity testing and for reference the temperature during my testing in the Sea Can was 23 degrees Celsius or 73 degrees Fahrenheit. For my accuracy portion of the shooting test I use a rested and seated shooting position shot 30 feet away from my fresh paper targets.
Starting off with the velocity or power potion of my Field Test Shooting Video for the Schofield No. 3 CO2 BB-Pellet Revolver. I first used the 4.5mm Steel BB shells and shot 3 rounds through my Chronograph averaging 369 fps. I then loaded up the Schofield No. 3 CO2 BB-Pellet Revolver with pellet shells and again placed three .177 caliber lead pellets through my Chrony and got a very similar result with an average of 361 fps. Keep in mind the lead pellets where 6.9 grain versus the steel BB’s at only 5.1 grain, so the lead pellets will be carrying more raw energy at the point of impact even though they where going just a tad bit slower than the steel BB’s.
In terms of accuracy both rounds performed about the same shooting at my paper target 30 feet away. Since the Schofield No. 3 CO2 BB-Pellet Revolver has a 6 round cylinder I shot 6 sounds for each test, 6 steel BB’s and then 6 lead pellets. I also changed the targets for each type of ammo between reloading. I found the Schofield No. 3 CO2 BB-Pellet Revolver shot fairly close to the bullseye, l but with both the Steel BB’s and lead pellets I got one outlier that spread out my groupings significantly, the other 5 rounds where all close being about 2 inches apart? Perhaps it was a bad or misshaped round, or maybe even me ;) I did notice the lead pellets seemed to have a really nice 4 round group out of the 6 that all fell within the bullseye. Hard to really say if BB’s or pellets performed better than the other one at least in my testing.
Overall the Schofield No. 3 CO2 BB-Pellet Revolver shot well for me, the trigger is nice and short and light making placing your shots easy, of course since it is a single action only trigger you kind of need to reset yourself between every shot which can effect groupings just a bit. Since the barrel is not rifled with no danger of damaging the rifling, you can really shoot what ever ammo type you feel like shooting or have on hand and since Schofield No. 3 CO2 BB-Pellet Revolvers get about the same speed and accuracy then it really doesn’t matter that much at the end of the day!
Type: BB/Pellet air revolver. Manufacturer/Distributor: Bear River. Model: Schofield No. 3 Materials: Mostly metal with plastic grips. Weight: 2.4 pounds. (1089 grams) Barrel: 7 inch (178mm) smooth bore barrel. Propulsion: 12 gram CO2. Action: Revolver, single action only. Ammunition Type: 4.5mm steel BB's and .177 Cal. Pellets. Ammunition Capacity: 6 rounds. FPS: 445fps.
Trigger Pull: The trigger pull on the single action only Schofield No. 3 CO2 BB-Pellet Revolver is what you would expect from a pistol of this design. Like the Colt Single Action Army the trigger pull is very short, light and crips, perfect for taking your time and getting a precise shot on target. You will of course have to cock the hammer manually before each shot ao no real action shooting.
Accuracy: I have not tested the Schofield No. 3 CO2 BB-Pellet Revolver in the Replica Airguns Sea Can Indoor Airgun Range but plan to get to it shortly. I will test out both 4.5mm Steel BB’s and some .177 caliber lead Pellets and see how the different ammo types effect both power and accuracy. Keep in mind the Schofield No. 3 CO2 BB-Pellet Revolver has a smooth bore barrel but I am pretty sure pellets will still perform well at 30 feet away.
Build Quality: The Schofield No. 3 CO2 BB-Pellet Revolver is built a lot like the Webley MK VI .455 CO2 Shell Loading Revolver line, perhaps even made in the same factory in Taiwan? The Schofield No. 3 CO2 BB-Pellet Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The pistol grips is a lot like what you have with the Colt Single Action Army pistol but the Schofield No. 3 CO2 BB-Pellet Revolver is a lot more front end heavy because of its beefy barrel.
Realism: In terms of replicating a real steel Schofield No. 3 CO2 BB-Pellet Revolver for sure looks and feels that part. The reassessed barrel and well hidden CO2 screw don’t give anything away that the Airgun version is not the real deal. But as with all of these shell loading Airgun Revolvers, the shells are actually closer to a .380 Caliber in diameter rather than a 45 which is what the real steel Schofield No. 3 CO2 BB-Pellet Revolver would be designed for.
If you are like a bulky revolver with good weight to it then the Bear River Schofield No. 3 is it.
Can shoot Steel BB’s or Pellets since it comers with both shell types.
Recessed barrel.
Well concealed CO2.
Shell loading design that loads from the back so no need to remove shells if you wish not to.
Single Action Only hammer and trigger action feel good, nice and light with short take-up and release.
Fairly discreet safety location right behind the hammer so easy to get at.
Super easy to load, pellet shells can even be reloaded with shells in the gun if you are using the pellet shells.
Really like the Nickel Finish on this gun.
Can get simulated Ivory grips for it if you prefer that look.
Cons:
Sights are not adjustable.
Warning instructions on side of the frame.
Barrel is not rifled for pellet use?
Only a Single Action Only Hammer and Trigger but true to the style of the gun.
Comments:
Yet another classic shell loading CO2 BB Revolver, and again the more the merrier in my option! I like that you get 12 shells with our kit version, 6 removable shells for 4.5mm Steel BB’s and 6 removable shells for .177 caliber Pellets. The Schofield No. 3 CO2 BB-Pellet Revolver is for sure a hefty revolver but the pistol grip is not super large so even people with smaller hands should not have a problem shooting the Schofield No. 3 CO2 BB-Pellet Revolver. The real problem is deciding which Shell Loading Airgun Revolver to buy now since we have so many to choose from… Classic or modern, nickel or black, or perhaps weathered?
My Table Top Review for the Schofield No. 3 CO2 BB/Pellet Revolver:
Here we have three very different products I Unbox and Preview for everyone. A Spring Piston multi-shot .177 Caliber Pellet Rifle, a single action BB/Pellet revolver that’s not a Colt! And a really nice looking Semi Auto Blank Pistol in a Chrome finish.
Let’s start with the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle. I think this is a really well thought out Air Rifle. It’s “almost a Bullpup” in design but it does actually load in front of the trigger just a bit, that said most of the spring piston is behind the trigger setup making it really compact yet with a longer than normal barrel compared to regular Break Barrel Spring Piston Air Rifles. The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle also has a side lever cocking mechanism along with a 5 round auto indexing magazine which makes it much quicker to cock and reload for fast follow-up shots, again compared to a standard Break Barrel Air Rifle, not to mention no barrel droop! The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle has a claimed fps of up to 500 so we are getting the max amount of velocity possible for our Canadian laws without making it a regulated firearm and requiring a PAL license. And by the way the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle does come in both a Lime Green and all Black version just in case you are not a fan of the Lime Green finish I show in this video.
Moving onto the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica, if you like single action revolvers then take a look at the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica. It’s a lot more bulky than a Colt Single Action Revolver and also has that top Break design that makes reloading quick and easy. The version we are selling inner Replica Airgun Online Store is the kit version that comes with 6 BB shells and 6 pellet shells so you can take your pick on ammo types. The barrel is not rifled so Steel BB’s will not hurt the Airgun and since pellets are skirted they do not need a rifled barrel to fly straight and true. You can expect around 445 fps for the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica.
Type: Blowback CO2 BB Pistol. Manufacturer: Distributed by Umarex. Model:Glock 19X. Materials: Metal & Polymer. Weight: 1.5 pounds (662 grams). Barrel: Smooth bore 3.36 inch barrel (85.3mm). Propulsion: CO2 x 1. Action: Semi auto blowback, double action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 18 round drop out full size metal magazine. FPS: Claimed 360.
Trigger Pull: The trigger pull on the Umarex Glock 19X CO2 Blowback BB Pistol is what I would call a double action trigger mainly because there is an indexing of the BB from the magazine into the breach area every time you pull the trigger which means the take up is longer thanks a standard Glock take up and there is a little bit of friction from the mechanical mechanism that indexes the BB making the trigger feel more like a double action only trigger.
Build Quality: TheUmarex Glock 19X CO2 Blowback BB Pistol seems to be really well made. Fit and finish are nice and slide wiggle is minimal. There is a bit of a clanky sound when the slide cycles but not as bad as the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. I also think the Coyote finish is the nicest looking with its black on tan two tone look.
Realism: The Umarex Glock 19X CO2 Blowback BB Pistol absolutely looks the part of a Glock 19X, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a CO2 mag. Mostly everything operates like a real Glock 17 but the slide is not a full blowback meaning it only goes back about 3/4 as much as a real Glock 17 slide would. One other noticeable difference is the ability to quickly field strip the Umarex Glock 19X CO2 Blowback BB Pistol, you will need to remove a pin since the take down tabs are non functioning and moulded into the frame. Available From: The Replica Airguns Store.
Pros:
Nice weight and feel to it, build quality seems good.
Really nice looking replica of the real steel Glock 19X, love the Coyote color.
Fully Glock licensed.
Easy to see white dot sights front and back.
Recessed barrel for added realism.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.
Safety built into the serial number plate area keeps it well hidden.
Warning instruction are nice and discreet under trigger guard
Not bad feeling double action only trigger as the blowback pre-cocks the internal hammer/strike.
360 fps is decent for a blowback BB gun.
Cons:
Does have blowback action but not full blowback.
Slide sound is a bit clanky but not as bad as the 17 Gen 3 Blowback.
Sight are non-adjustable which is common with low cost action shooters like this one.
Would have liked to have seen more pristine packaging from Glock over the plastic clamshell
Comments:
It’s great to see Umarex expanding their live of Glock licensed Airguns and the addition of the Umarex Glock 19X CO2 Blowback BB Pistol is welcome! Some of you are not going to like the semi blowback action but it does mean you get higher fps and more shots per CO2 while still getting that simulated recoil form the blowback action. I honestly thing the Umarex Glock 19X CO2 Blowback BB Pistol is one of the most attractive Glock Airguns with it’s Coyote Tan frame and slide with black highlights, I also like the compact size for its shortened frame and slide over the Umarex Glock 17 Gen 3 CO2 Blowback BB Pistol. So many to choose for now but I guess that a good thing or perhaps just get them all!
I though I would feature the fact that we recently added some of the Tokyo Marui product line to our Canada Replica Airguns Store. Tokyo Marui is said to be one of the best Airsoft products on the market and they have been around for a while so they have had time to get it right! As Tokyo Marui is a Japanese based company they are restricted to only being able to use plastic frames and slides but even with this limitation the Tokyo Marui products that I have personally looked at are extremely well made.
Type: Blowback CO2 BB Pistol. Manufacturer: Distributed by Umarex. Model:Glock 17 Gen 4. Materials: Metal & Polymer. Weight: 1.7 pounds (771 grams). Barrel: 3.6 inches metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, single action only trigger. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 18 round drop out full size metal magazine. FPS: Claimed 300.
Trigger Pull: The trigger pull on the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol is single action only so you will need to rack the slide first to not only chamber a 4.5mm Steel BB in the breach area but to also cock the internal striker. There is a working trigger safety on the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol and you’ll also find the Glock 17 Gen 4 has a nice short and light trigger as you would expect similar to the real steel Glock. Perfect for fast action shooting!
Accuracy: At this point I have not shot the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol so I can only quote what Umarex is saying in terms of FP2 which is 300. That sounds reasonable based on other Airguns like this that have that full blowback action since much of the CO2 gas is used to work the action of the slide. This not only reduces how many shots you can expect o get out of a single 12 gram CO2 cartridge but a reduction in power over non-blowback or even partial blowback CO2 Airguns.
Build Quality: TheUmarex Glock 17 Gen 4 CO2 Blowback BB Pistol looks to be well made overall with metal and plastic parts where you would find them on a real steel Glock 17 Gen 4. Fit and finish are nice and the slide wiggle is next to zero. The slide spring is very heavy and the sound of the slide when racked and released does not have that cheap metallic sound some blowback Airguns have. I am expecting some pretty decent blowback action recoil from the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol when I do my Field Test Shooting Review!
Realism: The Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol 100% looks the part of a Glock 17 4th Generation, sitting on the table and even holding it in your hand you are going to think it's the real deal until of course you drop the magazine and see that it is a BB/CO2 mag. Mostly everything operates like a real Glock 17 including the slide catch release, trigger safety, magazine release and even the take down switches for quick field stripping and access to the adjustable hop-up, yes it is adjustable. Available From: The Replica Airguns Store.
Pros:
Good weight and feel to it, build quality seems very good.
Really nice looking and full featured replica of the original Glock 17 Gen 4.
Fully Glock licensed through Umarex.
Easy to see white dot sights front and back.
Recessed barrel for added realism.
Accessory rail for adding a laser or tactical light.
Full size drop out metal magazine that holds the CO2 and 18 4.5mm steel BB’s.
Slide spring feels heavier than most full blowback Airguns, should have a heavy blowback recoil effect.
Safety built into the serial number plate area keeps it well hidden.
Comes with additional Backstraps for different sized hands.
Warning instruction are nice and discreet under trigger guard.
Great feeling single action only trigger as the blowback pre-cocks the internal hammer/strike.
300 fps is decent for a full blowback BB gun.
Cons:
FPS could be higher but fairly inline with other full blowback CO2 air pistols.
Sight are non-adjustable which is common with low cost Airguns like this one.
Would have liked to have seen more pristine packaging from Glock..
Comments:
I know everyone has been waiting for Umarex to release the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol and here it is finally, does it live up to all the hype and excitement? So far without shooting it I have to say yes, I am very pleased with how the Umarex Glock 17 Gen 4 CO2 Blowback BB Pistol looks and feels. There is not too much more you can ask for in a replica Airgun of any kind… it looks like the real steel version, it feels like there real steel version, it functions like there real steel version. Hopefully it shoots just as well! If you haven’t bought one of the Umarex Glocks so far then this one is the one to have, but I say why not have them all :)
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: GPM1911 Materials: Metal slide, frame & Magazine. Weight: 2.25 pounds (1020 grams). Length: 8.66 inches (22.0 cm) total. Barrel: 4.58 inches (11.7 cm),Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25 rounds. FPS: 300-330 fps.
Trigger Pull: The single action only trigger pull on the G&G GPM1911 GBB Airsoft Pistol is what you would expect from a traditional single action only 1911 trigger, a very short take-up and a crips and light release. Great for getting a lot fo shoots off quickly and accurately down range without making your trigger finger do a lot of work.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM1911 GBB Airsoft Pistol so I can into comment just yet but I will be making a Field Test Shooting Video for it as soon as I can and will post that here on the website and of course over on the Replica Airguns YouTube channel when I have it ready.
Build Quality: The G&G GPM1911 GBB Airsoft Pistol is in my opinion one for the nicer looking finishes wise and I would have to say it seems to also be one of the better quality 1911 Airguns out there, for sure a step up from a KWC blowback 1911’s and in line with what KWA and KJWorks is making these days which is good quality. The G&G GPM1911 GBB Airsoft Pistol is one of the heavier Airsoft 1911 Blowback Pistols which makes me think the metal is a bit higher quality where it needs to be. Tolerances are nice and tight and the blowbacks action is very heavy.
Realism: The G&G GPM1911 GBB Airsoft Pistol like most of these full blowback 1911 Airguns, Steel BB or Airsoft BB, is super realistic with an all metal build. All the real steel working parts like the slide catch release, back strap safety and pretty much everything else function as they should. The G&G GPM1911 GBB Airsoft Pistol even field strips like a traditional 1911 pistol. Not sure what you could do to make it more authentic for an Airgun?
Nice high capacity magazine compared to other GBB 1911 Airsoft pistols.
Heavier than most Airsoft 1911’s.
All parts fit nice and tight, tolerances are very good.
Working back-strap safety.
No ugly red tip.
Finish is really nice, gun looks really good.
Expect to get decent amount of shots per gas fill.
Micro Gas Filter and Whirl Cylinder Valve help to manage gas efficiency and reduced frost buildup.
Traditional adjustable Hop-up.
Full Size Dropout metal magazine pretty standard on Airsoft pistols.
Comes with high quality hard shell case and speed loader.
Cons:
Sights are pretty basic, no white dots and non-adjustable as you would expect on a 1911 A1.
Very simple Airsoft gun, no modern bits and pieces on it.
FPS could be a bit higher but fine for close quarters.
Comments:
The G&G GPM1911 GBB Airsoft Pistol is for sure one of the nicer 1911 A1 styled Airsoft pistols, inline with KWC and KJWorks. It does come in a little bit heavier and seems to have more blowback recoil action which is nice. All I need to do now is find out how well it shoots! If it’s not half bad then it is for sure worth the price which by the way is a little bit cheaper than a KWA or KJWorks 1911 and about the same price as a KWC 1911. So many choices I know but that’s a good thing :)
My Table Top Review of the G&G GPM1911 GBB Airsoft Pistol:
