Power Sources Covered in this review: CO2 - Spring Piston - Variable Pump -HPA (High Pressure Air)
Pro’s:
CO2 Airguns allow for fast repeat shooting, great for action shooters, generally CO2 Airguns will supply a medium power range. No need to pump or cock your CO2 powered weapon in-between shots and a CO2 power source can allow for a very realistic action of the gun you are shooting.
Spring Piston Airguns are best suited of single shot situations, they can provide low to high power output depending on the spring used. Spring Piston Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Spring Piston Airguns are not greatly effected by outside temperatures.
Variable Pump Airguns allow you to decide how much power your gun will have and can offer very high power output depending on the Airgun. Variable Pump Airguns are very low cost to operate since you only need to buy the Pellets or BB’s. Variable Pump Airguns are not greatly effected by outside temperatures. Variable Pump Airguns generally have very low recoil and vibration.
HPA (High Pressure Air) Airguns generally do not require pumping or cocking in-between shots and some even come in semi automatic or bolt action. HPA Airguns can have very high power output and even be used on larger game using large caliber ammunition. HPA Air Rifles have lower recoil and low vibration. HPA Airguns can be charged ahead off time so they are ready for use when you need them.
Con’s:
CO2 Airguns require the additional cost to buy the CO2 as they do not function without it. CO2 Airguns have a limited power output and lose power as you shoot and use up the CO2. CO2 Airguns are effected by hot and cold temperatures and will have less power in colder temperatures and may not even work in super cold environments.
Spring Piston Airguns require cocking before each shot. Spring Piston Airguns can have a lot of recoil and vibration, so much so that special optics must be considered when buying an optical sight. The action of the spring recoil can effect accuracy, especially if you are not use to the vibration and recoil or have spent some time practicing using a Spring Piston Airgun.
Variable Pump Airguns will require multiple pumps to achieved maximum power output which can take some time in-between shots. So you are going to have to work for each shot.
HPA (High Pressure Air) Airguns require the use of a manual pump to fill their built in air tank to maximum pressure and it does take a lot of time to manual fill an HPA tank. Alternatively you can have the air tank filled at a shop or buy a pressurization system similar to a scuba tank out paintball setup, the cost of this setup can be very high but will save you the castle of manually pumping air in to your HPA Airgun. HPA Airguns are generally a little more bulky then other Airgun systems since they have to accommodate fairly large air pressure tanks.
Power: Generally speaking a longer barrel is going to allow for more power. If you compare most CO2 pellet pistols to CO2 Pellet Rifles, you will find that the CO2 Pellet Pistol will generally shoot about 300-400 fps using a standard lead Pellet. On the other hand many CO2 Pellet Rifles can get up to as high as 600 fps which is much better speed for humanly shooting some smaller pests.
If you are talking about Springer or Variable Pump Air Pistols versus their Air Rifle counterparts, again the Air rifles will generally shoot with much more power. I have seen some none CO2 Air Pistols shoot up into the 500-600 fps range but again compered to none CO2 Air Rifles, they can even double these numbers.
Some of you may ask about Steel BB Pistols and Rifles. I personally would never really sue this type of ammunition for pest control simply because most BB Rifles have much less raw power than Pellet Rifles and steel BB’s will not be as accurate at any type of longer distance.
Stability: When holding any rifle from the shoulder, you have three point of contact with your body spread out in a much longer distance than a two handed pistol grip. Holding steady even without a rested position is much easier using a rifle. Even when using a rested position, the rifle will more stable.
Accuracy: A big factor in accuracy is stability but there are also other factors to consider. Barrel length its self does not make the gun more accurate, you only need a few inches of barrel length to get constant accurate results from a gun. What makes longer barreled guns more accurate is the distance between the rear and front sight. The closer the sights are together, the more margin for error there is, the longer you spread out the sights from each other, the more accurate the sighting system becomes.
Overall More Humain: When you consider Air Rifles tend to have higher power, better accuracy and overall more consistency than shorter barreled Air Pistols. The logical choice for humanly shooting a Pest is to use the Air Rifle. The last thing you want to do is make any animal suffer, even if it has been causing a lot of havoc around your home or farm or place of business.
This is not to say that a “Real Gun” is not as good as an Airgun or better in other ways, in this video I’m just pointing out how an Airgun in some cases can actually be better suited than a Real Gun.
Availability: What I mean by this, is that in many countries Real Guns can be very hard to acquire and often require safety course and applications before one can purchase a Real Gun. I have no problem with this but it is a reality that must be considered. Having an Airgun versus not having a gun at all makes it a better option for people that live in countries that have strict gun laws. Here in Canada we are allowed Real Guns, even pistols but we do have restriction on our pistols and so I can only get certain guns in an Airgun version. As a collector this is better than not having the gun at all.
Price to Buy: Generally speaking you can pickup an enter level Airgun for much less money than a real gun.
Cost to Shoot: Real gun ammo prices have been steadily increasing to the point that a day out shooting can cost several hundred dollars just on the ammunition alone.
Comparison of Price:
50 rounds of 9mm ammo will cost around $18.00
6000 rounds of 4.5mm Steel BB will cost about $18.00
CO2 is a bit less than $1 per 12 gram Cylinder which can yield up to 100 shots each.
To shoot 100 rounds of 9mm will cost close to $40 versus 100 shots of 4.5mm steel BB at around $1.
For this reason alone an Airgun can make a lot of sense even for Real Gun owners looking to get more cost effective practice time.
Access to Shooting Locations: Depending on where you live you will have to consider your local laws and where you are allowed to shoot both types of guns but typically you can shoot an Airgun safely just about anywhere as long as you implement some backstop safety precautions. Here in Canada we can only shoot a pistol at designated gun ranges, where as Airguns have a lot more allowances to shot them as long as you are not braking any city bylaws.
Training Guns: Even if you plan to eventually step up to a Real Gun at some point, an airgun is a great option to first learn proper gun handling skills since if you where to make a mistake, the consequences are much less severe. Airguns are also a lot less intimidating than a real gun since they are much quieter and have less recoil, you don’t even need to wear ear protection with most Airguns which means an instructor can communicate to his pupil on the range a lot easier.
Prop Guns: Since Replica Airguns look so much like real guns these day, they can often be used as a safer substitute for use in Movie, TV or other Photo and Video productions. Using a Real Gun on set generally requires a certified “Gun Wrangler” be on hand as Real Guns must be transported, stored and handled using very strict regulations. Airguns generally do not need to follow the same rigid regulations that Real Guns are bound to.
Tactical Training with Live Targets: Obviously shooting a real gun at a live target would not fair well for anyone involved, so that is completely out of the question. Airsoft Airguns are however perfect for Tactical Training and other weapons based simulations. All that is required for safety when using Airsoft guns is the use of eye protection and generally some heavy clothing.
I am sure there are some more areas in which Airguns may have the advantage over a Real Gun but these are the main ones that I could think of.
I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.
I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.
Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:
(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.
Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.
It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.
I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.
In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.
The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.
I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?
In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.
Some of the Shell Loading Revovers Tested in this Instructional Video are:
To make this as comparable a test as possible I used two KWC/Gletcher Makarov Full Blowback Pistols each with their own separate magazine, again one with a 12 gram CO2 and one using the ANT system.
HPA or High Presure Air is not effected by cold weather which makes this setup ideal for shooting in cold situations since fps is not effected at all. As CO2 requires heat to expand, the colder the outside temperature the less amount of expansion you get from the CO2 whihc results in less power, this is really noticeable on your follow-up magazines as the CO2, magazine and even the gun will have started to cool down from the CO2 exposure.
The ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit even when using large 20 ounce CO2 tanks will help with the cool down effect since the large CO2 tanks will take much longer to cool down and even freeze up as compared to the smaller 12 gram CO2 which can get frosty even after the first magazine.
I did notice in this Field Test Shooting Review that the CO2 did pretty good as it was my first magazine and the temperature was not all that cold out. I can say the HPA System was shooting much harder, after making this video I popped off another couple magazine with each gun shooting out to at least 100 feet and the ANT FIRE HPA setup was really throwing the 4.5mm Steel BB's out there quickly. As expected the 12 gram CO2 mags really started to trail off especially on the third magazine of shots.
All in all, the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit will not only bring your cost per shot down significantly but it allows you to keep shooting with no down time waiting for your gun to warm back up and the ability to use HPA (High Pressure Air) means you will get even more fps performance out of your air guns but also much more consistent shot performance all day long!
Well ANT (Advanced Novelty Tech) made an update model that supports a bunch more guns, that's a good thing of course. This new model is called the "FIRE" and it supports the following guns. I did find however that ANT list that the Gletcher NGT and Webley Mark VI Revolvers where supported by the FIRE but my findings indicated the CO2 screw on both these guns had a smaller diameter so they where not compatible. Other than that small discrepancy most of the other guns on their list should work just fine.
What exactly is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit?
The Advanced Novelty Tech FIRE CO2/HPA Conversion Kit is a remote line adapter for Airsoft, BB, and pellet guns. Compatible with over 60 guns, it is easy to install and converts a compatible gun for use with a Paintball remote line and CO2 or HPA tank. Eliminating the need for disposable CO2 cartridges, while still being interchangeable with disposable CO2 cartridges, it delivers a longer, more powerful, and more consistent shooting experience between refills.
So what is the ANT Advanced Novelty Tech FIRE CO2 HPA Conversion Kit going to do for you?
Eliminate the need for the more expensive disposable 12 gram CO2 cartridges.
Use interchangeably with disposable 12 gram CO2 cartridges.
Use in conjunction with a Paintball remote line with standard quick disconnect fittings and a CO2 or HPA tank. (recommended use up to 1000 psi)
Shoot thousands of rounds before needing to refill your CO2.
Fits compatible Airsoft, BB, and pellet gun CO2 pistols.
Easy drop-in installation.
Overall cost savings.
More consistent FPS especially when shooting fast or in full auto.
Almost a year or so ago I made my Table Top Review Video for both the 6mm Airsoft and 4.5mm Steel BB shooting KWC Mac 11 M11 CO2 Pistols, and no they are not machine pistols since they only shoot in semi auto mode. Well anyway, I finally got around to testing these low cost Mac 11 replicas out shooting them through my Chrony Chronograph to find out their real world fps velocity along with my standard 30 foot back semi rested paper target accuracy test. Both CO2 Replica Pistols performed rather well for me and turned out to be both powerful and accurate.
In terms of power, KWC claims 120 meters per second or 394 feet per second for the 4.5mm Steel BB KWC M11 while the 6mm Airsoft Mac 11 had a claimed fps of 152 mps or 499 fps. During my testing both guns actually shot much faster than claimed with the steel BB M11 shooting 5.1 grain steel 4.5mm BB's at an average of 453 fps. The Airsoft KWC Mac 11 with its lighter .20 gram 6mm plastic Airsoft BB's averaged a very hot 556 fps which is probably going to be too hot for most Airsoft fields but a lot of fun shooting in your back yard!
Both the Steel BB and Plastic Airsoft BB KWC M11's have an internal fixed hop-up system which did seem to help out a lot with accuracy. From my semi rested shooting position with paper targets setup 30 feet away, I was able to get well centered 1-5 to 2 inch groupings from both versions of the KWC Mac 11 CO2 Pistols.The Airsoft KWC M11 did shoot a little high and to the right but not a lot while the Steel BB M11 was centered well left to right but again just a little high.
Both KWC Mac 11 M11 CO2 Pistols shoot in double action and have what I would consider to be about medium pull triggers since there are not a lot of moving parts or any type of blowback operation. This means they will be more CO2 efficient and likely to have very few problems since they are very simple in design. If you want a great performing low cost and simple in design Mac 11 Replica then take your pick, 4.5mm Steel BB KWC M11 or 6mm Plastic Airsoft KWC M11!
I have already made a Table Top Video Review for the Gletcher NGT Silver CO2 BB Revolver which for the most part is the same gun but in a 4.5mm Steel BB non rifled barrel version and as the title indicates with a different finish being the silver version. Other than finish and ammunition being used, both guns are virtually the same.
I always like getting outside and shooting the airguns I review even on these fall overcast days, at least the temperature was not too cold, right around 14 °C or 57.2 °F so decent for my testing purposes. The Gletcher NGT R like the BB shooting NGT is a fairly small air revolver and so pretty much anyone should be able to shoot this air revolver even if you have smaller hands, I did find that pre-cocking the hammer for single action shooting was a bit of a stretch when reaching over with the thumb, but you can just as easily shoot in double action, both trigger pulls are nice and light with the double action being a bit longer and heavier.
Loading the 7 round cylinder will take longer than your standard stick magazine BB pistol since you first need to pop some .177 caliber pellets into each shell, if you want to speed up the process you don't have to eject the shells to load them, you can simply index the cylinder and pop a pellet into each shell while still inside the cylinder.
In terms of fps performance, the Gletcher NGT R CO2 Pellet Revolver shot a little higher than expected getting a 4 shot average of 376 fps using 7 grain RWS Lead pellets, so around 50 fps higher than the claimed 328 fps on the box and even a bit higher than the steel BB version I tested earlier. This is really good considering the short barrel and fact that a revolver can leak a little CO2 between the cylinder and the barrel and even the cylinder and the CO2 valve.
I really felt comfortable using the rather old school fixed open post and notch sights, the grey/black finish on the Gletcher NGT R may be a bit hard to see on darker targets but shooting on my white target was no problem. My 7 shot grouping from 30 feet back using a semi rested shooting stance produced about a 1 inch grouping well centred vertically just a hair to the left so all in all the Gletcher NGT R CO2 Pellet Revolver has the power and accuracy I was hoping for even in such a small package.
It has been a while since I picked out some of my favorite guns, after all my favorite gun picks change on a daily basis since there are so many awesome guns out there to pick from.
This Vimeo video is a little different since I pick out my favorites from a bunch of mostly replica gun categories including Steel BB, Pellet, Airsoft, Revolvers and Blank Pistols.
You may notice most of my picks happen to be blowback guns but to me airguns are all about being as realistic as possible and having blowback operation to me help to simulate the realism that much more. The exception in this video is in the pellet gun category since I decided on a pellet gun that was more about function and purpose over being any type of real replica.
Hopefully you take the time to watch my entire Vimeo video since I also bring out some close runner ups but here is a list of my top picks on this day, tomorrow it could be a completely different list of guns ;)
In this Field Test Shooting video I test out both the Daisy Powerline 5501 and Daisy Powerline 5502 CO2 Blowback BB pistols to determine what the real work velocity is and also how well they performs in terms of accuracy. To test velocities for both Airguns I use a my Chrony Chronograph and do my best to get 5 good readings which I then average out. I always use a brand new 12 gram CO2 cartridge and generally use 5.1 grain Zink Coated Steel BB's for my entire Field Testing. For my accuracy test, I set myself up 30 feet back using a semi rested position, to do this I place a sand bag up front to rest my hands and gun on and then stand securely in the back while I place 10 rounds on a paper target. There will obviously be some humane factor involved since I am not perfect but I can usually get a good idea on how accurate a given gun is using this method.
During my Velocity or FPS Chronograph testing, I managed to get 4 good readings out of 15 shots with the Daisy Powerline 5501 scoring an average of 367fps. Amazingly my first 5 shots with the Daisy Powerline 5502 all ready perfectly on my Chronograph even though they where moving a good 50fps faster, go figure? My average velocity for this 5 shot sting of shots was 417fps.
For my accuracy testing I was expecting both guns to perform about the same since mechanically they arevirtually the same other than a longer barrel on the 5502. The Daisy Powerline 5501 however seemed to struggle with consistency, it did group well left to right and up and down on the target but the spread was about 5 inches and it should of gotten closer to 2-3 inches in my books for a blowback pistol like this. The Daisy Powerline 5502 did perform better in terms of accuracy getting closer to a 2-3 inch grouping so overall I have to give the Powerline 5502 the advantage in both velocity and accuracy.
Another noteworthy point to mention is how much quieter the Daisy Powerline 5502 is in person! I am assuming the longer barrel along with the compensator perhaps muffling the sound a bit plays a roll in this. Both Daisy Powerline CO2 Blowback BB Pistols have a nice solid blowback action simulating some recoil and the triggers on both are fairly decent being that they simulate more of a double action feel with their long medium weight pull.
I do like the look of the more simplified Daisy Powerline 5501 with it's chrome frame but the performance and accessory option of the Powerline 5502 are a definite benefit for this model.
This comparison Review Video serves a few purposes, first to compare the ASG Dan Wesson 715 Revolver 4.5mm steel BB version to the 6mm plastic Airsoft version in both velocity and accuracy. Secondly to give my new Chrony Chronograph with lighting kit a test to see if I can get more reliable readings in lower light and thirdly to try and redeem the Steel BB version of the Dan Wesson 715 as last time I tested it, it did not get all that high of fps readings, well below the claimed 430 on the box.
In this review video I test both Dan Wesson 715 Revolvers out, first with my Chrony Chronograph and then all in one take I setup and shoot 6 rounds each on separate paper targets from 30 feet back to see how accurate the smaller heavier Steel BB rounds are compared to the larger lighter Plastic BB's. I used 5.1 grain RWS 4.5mm Steel BB's and .20 gram 6mm plastic BB's and installed brand new 12 gram CO2 cartridges in both guns.
In terms of my Chrony consistency, the smaller steel BB's still struggled to get consistent readings with only 2 out of 6 shots while the larger Airsoft BB's managed to get a good reading 4 out of 6 shots. Steel BB velocity was right around 350 fps while the Airsoft BB's where travelling much faster at closer to 450 fps.
Both the Steel BB and Airsoft CO2 Dan Wesson 715 Revolvers shot 6 round grouping of about 2 inches with 4 out of the 6 shots making a much tighter 1 inch group again with both ammo types. The Airsoft Dan Wesson 715 seemed to be centered on target well while the Steel BB Dan Wesson 715 shot a bit low.
Recently I picked up my new Chrony Beta Shooting Chronograph to replace my F-1 that has not been working so well for me in past videos... I wanted to get outside and give it a try shooting a few of the airguns that I was not able to test out properly. Now I know that under my patio deck, the lighting is not optimal even on sunny days and because of this I have never expected to get perfectly consistent fps recording but as many of you know, my old Chrony F-1 was pretty much not working at all near the end there.
I have ordered a light kit which will help out a lot especially when summer is over and the sky becomes more overcast. But for now I decided to test my Chrony Beta Chronograph under my deck roof as I have been testing all along and see if I can get better results with this newer Beta version.
So makes sure to watch my Vimeo video testing of my Chrony Beta Shooting Chronograph shooting a selection of airguns.
Here is my second instalment for this summers Full Auto Fun Videos. in this Full Auto Fun Video I shoot my KWC M712 Broomhandle CO2 BB Pistol at some more water filled Pop Cans and Clay Pigeons in Full Auto mode of course :)
Last summer I made some "Full Auto Fun" videos and well... I had a lot of fun making them and of course shooting the full auto airguns. So I got to thinking I should make some more Full Auto Fun videos again this summer, at least for some of the new Full Auto guns I have not made these videos for yet.
So to kick it off, I brought out my Umarex Beretta Mod. 92 A1 CO2 BB Pistol and shot up some clay pigeons and water filled cans in Full Auto Mode of course :)
Make sure to watch my Vimeo video for this Comparison Review as I go into a lot of detail about the similarities and difference with each of these CO2 Blowback Pellet Guns.
All of these CO2 blowback pellet guns are made for each company in Japan (I am assuming from the same factory?)
All of the listed Pellet Airguns shoot .177 caliber pellets (Can be Alloy or Lead)
They all have double sided rotary stick magazines that hold 8 rounds on each end for a total of 16 shots per magazine.
All of the Airguns use 12 gram CO2.
All compared pellet guns have Blowback operation.
All of these pellet pistols have single and double action triggers except for the Gamo MP9 which is single action only and needs to be charged on the first shot.
They all have rifled barrels.
Here is where we find some key differences between these CO2 Blowback Pellet Pistols:
Trigger Pull: The trigger pull on the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be. The blowback operation does place the hammer in the cocked position for single action type shooting but the the trigger is still required to index or advance the next pellet to line up with the barrel. Because of this, trigger pull is full length even in single action mode but you can barely feel any added friction from the indexing of the rotary magazine. All of this makes for a slightly longer trigger pull but one that is light weight with a fairly nice and easy release. For some reason the Sig Sauer P226 trigger does feel a little smoother with a slightly easier release.
Accuracy: I have not done my official Field Test Shooting Video with the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol and I am not sure when I am going to get the chance to do so since I am waiting on a replacement Chronograph for my velocity portion of my testing. That said I can say that Sig has already done some of the work for me and conducted their own "real world" velocity testing for their ASP line of CO2 Pellet Guns. Sig tested both a standard 8.18 grain lead pellet and a high velocity 5.25 grain alloy pellet shooting an 8 shot string with each to find out average fps performance for both pellet types. The 8.18 grain lead pellet average 353 fps while the 5.25 grain alloy pellet average 399 fps. In terms of accuracy, I was able to get just under a 2 inch 16 shot well centered grouping on two separate 30 foot back tests which is pretty decent. I did notice that when shooting a 16 shot string, the first and last shot velocity will vary a fair amount as the CO2 cools the gun and lowers the fps. I would recommend taking your time in-between reloads to let the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol warm back up.
Build Quality: The Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is a bit on the lighter side coming in around 1.5 pounds since it does incorporate both metal and plastic construction. You will find the Sig Sauer P250 has a metal slide and plastic frames similar to the real steel version. Weighing it at 1.45 pounds, the P250 is lighter then a standard Sig Sauer P250. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.
Realism: The Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P250. I really like the fact that the safety also works as a working decoker just as it would on the real Sig P250. Other similar working parts are the magazine release and the hammer that stays back for true single action shooting. The slide catch release and take down leaver are purely for show but they are not moulded in parts so they look good and realistic. One slight disappointment for me is when a gun does not have a cut out ejection port, that is the case with both the Sig Sauer ASP P226 and P250 but it does not take away from the shooting fun in any way.
Good overall replica of the real steel Sig Sauer P250.
Designed by Sig and made in Japan, fully Sig Sauer licensed.
Nice heavy blowback operation.
It might feel a bit light weight at first but out of the two Sig Sauer ASP pellet pistols this one seems to shoot a bit better.
Got respectable accuracy and seemed to shoot pretty hard.
Safety works as the de-cocker same as the real Sig Sauer P250.
White dot sights and accessory rail.
Great feel to the trigger not heavy or sticky in any way.
Cons:
Shots tended to slow down a bit near the end of a 16 shot strong as the gun cooled down.
Sight are non adjustable.
Ejection port is not cut out.
Comments:
What I really like about the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol is that like all the other APS Airgun from Sig, it is a product that Sig has decided to invest a lot of their time and effort to develop rather then simply grab an existing Airgun product from a manufacturer and slap their license on it. Sigs product ingenuity is what will help to improve the airgun industry overall. Getting back to the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol, it may feel a bit light weight at first but the heavy blowback will rock you unexpectedly! I found in terms of comparison to the Sig Sauer ASP P226, the P250 was more accurate and well centered on target for me as well. If you're a Sig Sauer P250 owner you are for sure going to want to pick yourself up one of these ASP CO2 Blowback Airgun versions so you can get some extra practice time in for pennies per shot and the ability to shoot in a lot more locations..
My Vimeo Table Top Review of the Sig Sauer ASP P250 CO2 Blowback .177 Caliber Pellet Pistol:
Trigger Pull: The trigger pull on the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be. The blowback operation does place the hammer in the cocked position for single action type shooting but the the trigger is still required to index or advance the next pellet to line up with the barrel. Because of this, trigger pull is full length even in single action mode but you can barely feel any added friction from the indexing of the rotary magazine. All of this makes for a slightly longer trigger pull but one that is light weight with a fairly nice and easy release.
Accuracy: I have not done my official Field Test Shooting Video with the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol and I am not sure when I am going to get the chance to do so since I am waiting on a replacement Chronograph for my velocity portion of my testing. That said I can say that Sig has already done some of the work for me and conducted their own "real world" velocity testing for their ASP line of CO2 Pellet Guns. Sig tested both a standard 8.18 grain lead pellet and a high velocity 5.25 grain alloy pellet shooting an 8 shot string with each to find out average fps performance for both pellet types. The 8.18 grain lead pellet average 359 fps while the 5.25 grain alloy pellet average 403 fps. In terms of accuracy, I was able to get about a 2 inch 16 shot grouping on two separate 30 foot back tests which is pretty decent. I did notice that when shooting a 16 shot string, the first and last shot velocity will vary a fair amount as the CO2 cools the gun and lowers the fps. I would recommend taking your time in-between reloads to let the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol warm back up.
Build Quality: The Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is a very solid feeling pistol with its all metal construction. Weighing it at 2.35 pounds, it is actually a tad bit heavier then the real steel version but not by much. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.
Realism: The Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P226, I would say it most closely takes after the MK-25 Threaded Barrel version. I really like the fact that the safety also works as a working decoker just as it would on the real P226. Other similar working parts are the magazine release and the hammer that stays back for true single action shooting. The slide catch release and take down leaver are purely for show but they are not moulded in parts so they look the part. One slight disappointment for me is when a gun does not have a cut out ejection port, that is the case with both the Sig Sauer ASP P226 and P250 but it does not take away from the shooting fun in any way.
Good overall replica of the real steel Sig Sauer P250.
Really solid feeling gun, has awesome weight to it with it’s all mental construction, pretty close in weight the real steel version.
Designed by Sig and made in Japan, fully Sig Sauer licensed.
Nice heavy blowback operation.
Got respectable accuracy and seemed to shoot pretty hard.
Safety works as the de-cocker same as the real Sig Sauer P226.
White dot sights and accessory rail.
Super easy CO2 loading system, no having to tighten a CO2 tab.
Great feel to the trigger not heavy or sticky in any way.
Cons:
Shots tended to slow down a bit near the end of a 16 shot strong as the gun cooled down.
Sight are non adjustable.
Ejection port is not cut out.
Comments:
What I really like about the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol is that like all the other APS airguns from Sig, it is a product that Sig has decided to invest a lot of their time and effort to develop rather then simply grab an existing arigun product from a manufacturer and slap their license on it. Sigs product ingenuity is what will help to improve the airgun industry overall. Getting back to the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol, it's a really solid CO2 Pellet pistol that is a lot of fun to shoot and for Sig Sauer P226 owners, the pellet shooting airgun version offers a super economical and safe way to get some practice in using a product that looks, feels and shoots similarly to their real steel counterpart.
My Vimeo Table Top Review of the Sig Sauer ASP P226 CO2 Blowback .177 Caliber Pellet Pistol: