It was a decent day today, not too cold and not raining at least at the time I and ethics video :) I figured with my new Insta60 One R and iVUE Vista cameras it would be a great day to test them out outside shooting with my G&G SMC-9 Full Auto Airsoft Carbine. I like the bak for more regulated Indoor Field Tests, these outside usually clay pigeon shooting videos are a lot more fun and I think a nice break for everyone.
So in this video I have three cameras rolling and switch camera switch back and forth throughout the video to make the experience more immersive. I have cameras setup front and back (Sony RX100 IV in front & Sony HDR-AS15 Back), along with my iVUE camera glasses and my Insta360 One R mounted to the barrel of my G&G SMC-9. All in all I think the video turned out well. It may be time to upgrade my Sony Action Camera as it is probably the oldest camera in my collection and you can see in the video it does not look as good as the other cameras.
In this Field Test Shooting Video I test out the G&G SMC-9 GBB Airsoft Carbine in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see if the real world performance matches the manufacturers claims. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up extended magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect and then just for fun I shoot the 40 rounds left in the 50 round magazine in full auto to see how this also effects accuracy.
Starting with my Chronograph test, the G&G SMC-9 GBB Airsoft Carbine averaged 339 FPS with the fastest shot recorded at 350 fps and the slowest being 324 fps, so very consistent in terms of sustained fps during my Chronograph velocity testing. The velocity was a bit under the claimed 366-375 fps but I was using slightly heavier BB’s and it wasn’t super warm temperatures in the Sea Can on this testing day, around room temperature, (20 degrees Celsius or 68 degrees Fahrenheit).
Moving onto the accuracy testing for the G&G SMC-9 GBB Airsoft Carbine, it performed pretty decent shooting about a 10 round 4 inch grouping but if I removed two flyers top and bottom the grouping would have been loser to 1.5 inches. The grouping was well centered on the target but I did adjust the sights up a bit as initially out of the box the G&G SMC-9 GBB Airsoft Carbine was shooting fairly low at 30 feet out. The good news is the G&G SMC-9 GBB Airsoft Carbine has fully adjustable sights for windage and elevation along with the 120 clicks of hop-up adjustment. When it came to my full auto testing I found I was shooting really low, perhaps from the blowback recoil pushing me of target? This was the case at least when I did a 40 round mag dump. When I performed the test using shorter bursts I was able to keep more rounds centered on the target for sure but accuracy in full auto was not nearly as good as in semi auto because of the heavy blowback.
Over all the G&G SMC-9 GBB Airsoft Carbine performed decent for me, the velocity was bang on right around what is claimed by G&G allowing this GBB Airsoft Carbine to shoot targets at further out ranges. Accuracy in semi auto was also very good but again shooting in full auto will take a bit more of your attention keeping the blowback recoil under control, for this reason burst fire in full auto will give you better accuracy which is more than likely how you would be shooting the G&G SMC-9 GBB Airsoft Carbine anyways. I really like the diversity you get with the G&G SMC-9 GBB Airsoft Carbine and if you are into Gas Blowback Airsoft guns, then I feel you get similar performance to an AEG but with a lower capacity magazines, but then again I may just have to get my hands on a drum magazine for the G&G SMC-9 GBB Airsoft Carbine and see how that changes things.
Type: Gas Blowback Airsoft Carbine. Manufacturer: G&G Model: SMC-9 Materials: Metal/Aluminum & Polymer. Weight: 4.7 pounds (2125 grams). Length: 410/620mm folded/unfolded length Hop-up: Yes - 120 click adjustment. Propulsion: Green gas or propane. Action: Semi & Full AutoBlowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 50 rounds. FPS: 366-375 fps.
Trigger Pull: The trigger pull on the G&G SMC-9 GBB Airsoft Carbine is typical single action only with a soft short take-up and light release point. I would not call this a crips trigger since it does have a rather spongy feel to it but this is only noticeable when you are easing the trigger slowly. In reality you will be engaging the trigger quickly when shooting it on the field and won’t notice any of the creep or take-up. I would consider it to be a decent trigger pull over all.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G SMC-9 GBB Airsoft Carbine but as with most of my Full auto Airguns I find it hard not resist going outside and blasting off at least one magazine in full auto. Of course this was the case with the G&G SMC-9 GBB Airsoft Carbine and I can tell you I went through all 50 rounds in not time and the G&G SMC-9 GBB Airsoft Carbine rounds went exactly where I pointed the gun short and long range so I expect my Field Test Shooting video to produce good results.
Build Quality: The G&G SMC-9 GBB Airsoft Carbine feels amazing in the hand with a lot of metal going on in the upper Carbine conversion kit portion, the front rail assembly is CNC Aluminum and the Pop-up iron sights are actually metal. The rear fold out stock is plastic but it is sold and just like the rest of the G&G SMC-9 GBB Airsoft Carbine very well made with great fit and finish. Of course the lower polymer frame is from the G&G GTP9 and just like all of the G&G pistols is very well made.
Realism: The G&G SMC-9 GBB Airsoft Carbine genuinely feels like a real steel firearm when holding it in the hand. Shooting it feels much the same but obviously with a lot less recoil than a powder burner. Just like a real steel 9mm Carbine the G&G SMC-9 GBB Airsoft Carbine mechanically works virtually the same with working slide catch release, charging handles, magazine release, and duel safeties, all ambidextrous by the way. As expected you can fully field strip the G&G SMC-9 GBB Airsoft Carbine.
Lots of metal parts giving the G&G SMC-9 GBB Airsoft Carbine really good weigth and feel.
Fold out stock sits nice and tight using magnets when not in use.
Integrated QD sling swivel.
Comes with two different sized Back-straps to accommodate small and larger hands.
Super high capacity extended 50 round magazine that holds a ton of gas for consistent power and lots of shots per fill.
Converts the standard GTP9 semi auto pistol into a full auto Carbine.
Almost everything is ambidextrous.
CNC 20mm / MLOK Rail for lots of accessories options.
Actual metal pop-up fully adjustable sights.
Easy to adjust hop-up without disassembly.
Dual safety system, cross bolt on frame and trigger safety.
Cons:
Fold out stock is not adjustable which makes the sights are a bit tight.
Does not come with the pistol slide if you want to covert it back to the GTP9.
Comments:
I am a big fan of the full line of G&G Airsoft guns and so far their GBB pistol lineup has been a treat to review, adding their new G&G SMC-9 GBB Airsoft Carbine to the lineup for me is the perfect mix between their GBB Pistol lineup and their mostly AEG Rifle lineup. I am hoping to see if I can acquire the drum magazine and eventually see how that works with the G&G SMC-9 GBB Airsoft Carbine, for now the 50 round extended magazine will have to do. Really looking forward to testing out the G&G SMC-9 GBB Airsoft Carbine so stay posted for those results shortly!
My YouTube Table Top Review of the G&G SMC-9 GBB Airsoft Carbine:
I am super excite to showcase three awesome rifles in this Update Preview Unboxing Video. Two of which are Airsoft and one is a Steel BB shooter, all of which are semi and full auto selectable. In this video I do a bit of an unboxing and preview of each Rifle not going into too much detail as I want to leave most of the information for my Table Top and Filed Test Videos. The main purpose of this video is to let everyone know we have these Rifles in our Canada Replica Airguns Store now for sale.
I may as well talk about them in the order they appear in my video so lets start with the ICS CXP APE AEG Airsoft Rifle. The ICS CXP APE AEG Airsoft Rifle is a mostly metal Electric Airsoft Rifle with realistic electronic blowback operation along with a CNC machined aluminum upper and lower receiver. It comes with a hi-cap 300 round magazine and a Ver 2 Full Metal ICS Split Type Gearbox. The ICS CXP APE AEG Airsoft Rifle weighs in at just under 3kg.
Next I showcase the G&G SMC9 GBB Airsoft Carbine, a unique product that converts the G&G GTP9 pistol into a a semi and full auto Carbine and includes a 50 round extended magazine, there is an even higher capacity drum magazine made for this product! You will find a fold out stock along with a CNC Machined MLOK Rail for additional mounting options.
Last but perhaps one that I have been the most eagerly anticipating is the Crosman AK1 CO2 Blowback BB Rifle a twin CO2 Blowback 4.5mm Semi and Full auto AK style BB Rifle, finally a decent AK BB Rifle! The Crosman AK1 CO2 Blowback BB Rifle has a claimed fps of 430 and shoots 1400 rounds per minute in full auto, very similar to the Crosman DPMS series of AR styled CO2 Blowback Full Auto BB Rifles. The Crosman AK1 CO2 Blowback BB Rifle comes with a 25 round magazine and swing out rear adjustable stock.
To celebrate Victoria Day here in Canada we are having a SALE over in the www.ReplicaAirguns.ca Online Store! Everything will be 10% OFF! Sale will go over this weekend and end Monday night.
We are featuring a couple of newer products in the Canada Store, one from G&G and one from Umarex…
Type: Airsoft AR, M4, M16 Styled Rifle. Manufacturer:G&G. Model:ARP-556 and ARP-9. Materials: Metal and plastic/polymer construction. Weight: (ARP-9 4.4 pounds) (ARP-556 5.3 pounds). Barrel: 6 inches, metal non-rifled. Propulsion: AEG non-blowback. Action: Semi & full auto SAO. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: (ARP-9 300) (ARP-556 450). FPS: 400+.
Trigger Pull: The trigger pull on the G&G ARP rifles is an electric mechanical trigger that simulates a single action only trigger. There is essentially a light spring internally which supplies the trigger pressure. Pressure is even and smooth.
Build Quality: As with all of the G&G product line the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles are really well made. Fit and finish is flawless and I had no issues shooting these guns at all. Every engagement of the trigger resulted in an Airsoft BB downrange and in full auto mode BB's where literally streaming from the barrel :) You will find a little more metal specifically in the receiver for the G&G ARP-556 over the G&G ARP-9 AEG Airsoft CQB Rifle which does make the ARP-556 a little bit heavier but not by much.
Realism: Both the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles are super realistic, they are based on the AR, M4, M16 Rifle design but are scaled down for tactical close quarters use with their compact barrels and adjustable stocks. Most parts work as you would find on a real steel M4 like the charging handle, dust cover, simulated forward assist and of course the magazine releases. There is however no blowback operation but I can attest that if you have an 11.2 volt battery and are shooting in full auto you will feel this gun a rock'n.
2 lower and higher priced models with similar looks and performance to choose from.
Super compact CQB rifles.
Fully adjustable pop-up iron sights front and back.
Crown flash hider acts as a sound amplifier if you’re into that sort of thing?
Great internals, Internally upgraded with an ETU and MOSFET system.
Skeltonized PDW stock perfect for close quarters combat.
Nice 400 feet per second velocity, good for close and even further out ranges.
Very accurate, one of the best Airsoft rifles tested to date.
ARP-526 has an ambidextrous selector / safety switch.
ARP-556 has full metal receiver.
ARP-9 is a bit lighter and less tiring to carry, great if you plan to add on a bunch of accessories.
Cons:
No blowback operation.
ARP-9 has a plastic receiver.
You need some pretty compact batteries to fit into the short bumper tube.
Comments:
I am going to go on the record and say that the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles would be my go to Airsoft battle rifle of choice. They have enough power for out door shooting and not too much for indoor shooting. Their compact and lightweight design will make them super easy to carry around all day and quick to place on any target in a hurry. Accuracy is not a concern since these AEG Airsoft Rifles can cut a bullseye out of a paper target no problem. Price for what you get, quality, looks. performance are all top notch with either choice of G&G ARP-556 or ARP-9 AEG Airsoft CQB Rifle you decide to go with.
My Vimeo Video Review for the G&G ARP-556 and ARP-9 AEG Airsoft CQB Rifles:
It's been a rather long time since I made an Airsoft Rifle Field Shooting Test video. I like to shoot a bit further out than 30 feet when using a rifle. Unfortunately the weather outside is getting really cold where I live so my testing will have to all be done inside the Replica Airguns Sea Can Airgun Range which only allows for about 30 feet worth of distance to my paper target. I figure if I can get a tight group at 30 feet than it shouldn't spread out too much at longer ranges!
Since the G&G ARP-9 and G&G ARP-556 have identical internals and similar barrel lengths I figured I only really needed to test one of them out so I picked the G&G ARP-556 AEG Airsoft CQB and put 5 shots through my Chrony Chronograph to get my Field Test Started. The G&G ARP-556 AEG Airsoft CQB shot a nice consistent 400 fps which is as high as I would want to go for indoor CQB type shooting. The BB's sure did get to my paper target quickly!
I followed my velocity testing with an accuracy test at 30 feet back using a rested shooting position, sand bag up front and sitting in the back. I first placed 10 rounds on my paper target in semi-auto and hit the 1.5 inch bullseye with every shot! I think this may have been a first for me using an Airsoft rifle? Of course I had to switch the G&G ARP-556 AEG Airsoft CQB over to full auto and see how she would perform. Since I was using an 11.2 volt bolt battery the rate of fire was crazy fast but even so in full-auto the bulk of the shots still hit the center bullseye cutting out a 2 inch hole in my paper target. The G&G ARP-556 AEG Airsoft CQB is a beast that I would not want to be on the receiving end of!
I'm pretty sure I found my go to AEG M4 styled CQB rifle, I'm not sure how you could beat the results I got shooting the G&G ARP-556 AEG Airsoft CQB. And if you're looking for a slightly lighter and less expensive version with the same performance then take a look at the G&G ARP-9 AEG Airsoft CQB.
I just received some really nice G& G Airsoft guns to share with everyone, I have two CQB Styled AEG rifles and a fantastic Gas Blowback Beretta Mod. 92FS.
The AEG CQB AR or M4 styled rifles are similar in a lot of ways and are super compact and really well built. The G&G ARP-9 has a polymer receiver and hand guard while the G&G ARP-556 has a full metal receiver and hand guard. Both have good weight to them. You will also find Skeletonized PDW stocks and large crown flash hiders on both models along with M-LOK hand guards. Inside you will find upgraded ETU and MOSFET electronics.
Obvious difference are the 9mm style magazine found on the G&G ARP-9 versus the M4 styled high capacity magazine on the G&G ARP-556. You also get an ambidextrous safety sector switch on the G&G ARP-556.
Next I show off the G&G GPM92 Beretta Mod. 92FS Gas Blowback Airsoft Pistol. It comes in a high quality hard plastic case with a well made speed loader. If you place the magazine in the gun you will have room for two magazine in the hard shell case. The G&G GPM92 hold 27 roads in it's double stack magazine that has some interesting new features that help it perform much beet in cold environments and really boost green gas usage. G& G calls them the Whirl Cylinder Valve system and Micro gas filter. Both help eliminate free up in the gun when shooting fast.
The G&G GPM92 Beretta Mod. 92FS is really well made and shoot in double and single action and the safety even works as a decocker. For those looking to add a mock suppressor you will happy to know the G&G GPM92 has a threaded barrel tip.
This Vimeo Unboxing Preview Video focuses on two AR M4 styled AEG Airsoft Rifles. The G&G CM16 Rifles are all pretty much the same other than the barrel lengths and come in the following versions, the CM16 SRS, CM16 SRL and CM16 SRXL. I also showcase the Umarex HK M27 which is distributed by Umarex but made by VFC which is knwo for their high quality products. I will be following up this Preview Unboxing Video with individual more detailed Review videos for each AEG AR M4 rifle.
Trigger Pull: The trigger on the G&G GR14 Type 57 R.O.C. is like most AEG Airsoft Rifles, being that it is essentially an electric on off switch and not a mechanical one. So it is light with not much take up. You will notice a bit of delay from the time your press the trigger till a BB is released since the electric motor must first pull back the spring and release it.
Accuracy: So far I have not tested out the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle. When I get the chance, I will have to set my paper target up further out than my usual 30 feet! I am also expecting the fps to be a bit higher than the stated factory default since this G&G GR14 AEG Airsoft Rifle is marked as being the "High Muzzle Velocity Version"! Stay tuned for my future Field Test Shooting video for the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle.
Build Quality: The G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle looks to extremely well made with most of the build materials being metal and wood. The only none metal or wood noticeable parts would be the upper hand guard which is made out of some sort of nylon or plastic. I believe the original M14 Rifle upper hand guard was made out of fiberglass. Then Walnut Wood Stock is nicely finished and the metal parts function and look really great.
Realism: In terms of realism the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle is extremely authentic in terms of looks, weight and even overall length and barrel length! Most of the parts operate exactly as they would on the real M14 rifle including the selector switch, safety, magazine release, shoulder rest adjustable sights and bolt.
Lots of metal and wood parts where they would be on the real M14.
True realistic 9 pound weight.
High capacity magazine at 470 rounds.
Sights are adjustable for elevation and windage.
Semi and Full Auto selectable.
Real Walnut Wood Stock.
Flip up metal shoulder rest.
Engraved with "The Republic of China" Chinese Text Markings.
25000 rpm Hi-torque Long axis Motor with 7/8 mm Bearings.
8.4v Large Tamiya Battery System.
Cons:
Does not come with battery or charger.
Not setup as is for a scope.
Comments:
History of the M14 this rifle is based on - "The M14 rifle, formally the United States Rifle. M14 is an American selective fire automatic rifle firing 7.62x51mm NATO (.308 Winchester) ammunition. It was the standard issue U.S. rifle from 1959 to 1970. The M14 was used for U.S. Army and Marine Corps basic and advanced individual training and was the standard issue infantry rifle in CONUS, Europe, and South Korea, until replaced by the M16 rifle in 1970."
So the M14 has a place in our history books and also a place in many of our war veterans hearts. This G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle replica is an excellent example of such a great piece of history, to have one in a working Airsoft version may be the next best option to having the real deal.
My YouTube Review Video of the G&G GR14 AEG Type 57 R.O.C. Walnut Wood Stock Airsoft Rifle:
In this Video Review I show you around the G&G CM16 Raider and Carbine AEG Airsoft Rifle's. Since these AEG Airsoft AR Rifles are a bit large to showcase using my traditional Table Top location I move into my gym and take each gun out of its box to have a good look at them. I talk about some of the main features and specification. The main features being these G&G CM16 AR15 / M16 AEG Airsoft Rifles are all really well priced but also very well made for their rather low overall cost. They do have a primarily all Nylon Fiber build even in the receivers but they still have a nice 4.6 to 5.7 pound weight to them, and once dressed up with a few accessories they come in at a perfect weight that is not too heavy to carry around in just about any game situation. The Nylon material in some way is a better choice in terms of getting scratched and dinged since they will not mark up as easily as painted metals will.
We carry a lot of the G&G line and perhaps have as much in stock as you would find at the G& G booth ;) I did see a few items we do not have in stock so I will have to see what I can do about that. Some products that I hope to see added to our Canada Replica Airguns Store would for sure be the M1 Grand and our Canadian Military Colt C7A1/2.
Trigger Pull: The trigger pull on the G&G AR styled Airsoft CM16 Raider is very smooth, the CM16 Raider uses a mechanical trigger that once the charging handle has been pulled back or "charged", works in a single action only manor with a slight bit of take-up and then a light predictable release. Each time the closed bolt gas blowback system shoots a round in semi or full auto, the internal action is ready for the next single action shot.
Accuracy: So far I have not tested Version 2 of the G&G CM16 Raider, but I have tested Version 1 so here are the result I got with Version 1 until I do my official Field Shooting Test with Version 2. When shooting from a 30 foot distance I did get some nice closely grouped shots from the G&G CM16 Raider Gas Blowback but when shooting in full auto it did spread apart somewhat, maybe from the GBB recoil? Version1 of the G&G CM16 Raider GBB shot an average of just over the 325 fps, I was using .25 gram BB's and it was a cool day so you can expect higher fps out of the G&G CM16 Raider when conditions are better.
Build Quality: The G&G CM16 Raider GBB being built on G&G Combat Machine Platform is targeted more for the price conscience person. The quality is consistent and good and I did not mind having more plastic in the G&G CM16 Raider GBB as my plan from the beginning was to add a lot of extra accessories and starting out with a somewhat lighter footprint made the gun still relatively usable even when all geared up with extra accessories. I also feel the plastic or polymer fiber upper and lower receiver and RIS rail system will also wear better than steel as it is more likely to flex rather than break in many situations, not to mention metal will show scratches and wear more over time.
Realism: Airsoft AR rifles in my opinion are very realistic in general, even the AEG versions work just like the real steel AR's with working charging handles, dust covers, bolts, magazine, adjustable stocks and sights, but I would have to give the advantage to the gas Blowback systems like the G&G CM16 Raider GBB as it has a full internal bolt with some decent recoil, it can also be field striped very similarly to a real AR15 rifle. The shot count is more like what you would find in an M16 or AR rifle which means you will need to consider ammo shot assuage and reloading more carefully when using it in an Airsoft game.
Super affordable Gas Blowback Airsoft AR M16 styled Rifle.
Very high rate of fire in full auto.
Polymer shell is both light and very durable, does not show scratches or wear as easily as metal.
All most every part is operational - Fully Ambidextrous now.
Can be fully customized, lots of mounting points on the RIS Rail system.
Fully adjustable Crane Stock.
Removable rear Iron Sight can be swapped out for other sighting systems and hardware.
Version 2 is a significant upgrade from Version 1.
Internals can be swapped over to make it an AEG gun.
Cons:
Some people may not like the polymer RIS rails and upper and lower receiver?
Would have liked to have seen some sort of a plate over the pistol grip to finish it off.
Comments:
I already really liked Version 1 of the G&G CM16 Raider GBB Airsoft AR Rifle and even bought a bunch of magazines and gear to sport mine up for use in some local Airsoft games, the upgrades and improvements found in Version 2 are the icing on the cake! I am hoping the internal performance enhancements will increase the FPS just a bit and Gas efficiency somewhat over Version 2 but will find out when I give it a thorough testing shortly. If you have been a bit scared off by the higher prices of some GBB Gas Blowback Airsoft rifles then perhaps take a look at the G&G Combat Machine Platform CM16 Raider in GBB, it may just change your mind about Gas Blowback Airsoft rifles!
My Vimeo Video Review for the G&G CM16 Raider Airsoft GBB AR Styled Airsoft Rifles:
You may wonder why I am doing another video on the G&G CM16 Raider Gas Blowback Airsoft AR Rifle? That's because the one I have here in this Update Video is Version 2 and yes there is a difference. So far I can only tell you about the obvious stuff since I really have not tested it out to see if there are any other performance gains with Version 2 over Version 1.
G&G has made some improvement with Version 2 enhancing several areas:
First off, there is now a selector switch on both sides of the receiver allowing for left or right handed use.
Carrying on with the ambidextrous theme, G&G also added a magazine release to the left side of the receiver.
Another missing feature was a bolt lock out when your magazine was empty, this has been added and so the bolt will lock back about 1/3 the way back locking out the gun and letting you know when you are out of ammo.
The bolt release on Version 1 was just for show and did not function. On Version 2, with the bolt lock, G&G also added a working bolt release.
Those are some pretty significant improvements to the G&G Armament CM16 Raider GBB Version 2 in my books! So now it's time to test it out and see if full auto mode has been improved. I found with Version 1, that when using full auto, the G&G CM16 Raider GBB would have some trouble getting through a full mag dump but when shooting very quickly in semi auto had no problems at all.
I am happy to report back to you on all the new cool stuff I got to see at this years 2013 SHOT Show in Las Vegas. Make sure to also watch my Vimeo video at the bottom of this post for some first person styled play by play of my experience at the Vegas SHOT Show 2013. (like you're there with me ;)
First up I want to cover a new gun from ASG, I have been wanting to get my hands on the 4.5mm Bersa BP9CC and I finally got to, not only did I get my hands on it but ASG was kind enough to supply me with one to take home for review. You can get the Bersa BP9CC in both Blowback and non-blowback versions and also in either BB or Airsoft. I opted for the 4.5mm BB Blowback version. I will be reviewing this BB gun very soon!
ASG also had a very cool prototype of an Airsoft CZ Scorpion EVO 3A1 hopefully coming out soon.
While roaming around SHOT Show 2013, I came across an interesting booth from FlashFog Security. I often get people asking me about using an airgun as a home defense weapon and I strongly advise against this. If the intruder is not scared off by the gun there is little an airgun can do to actually stop them. The FlashFog system works by rapidly filling a room with dense fog combined with a strobe light effect which blinds and disorients intruders completely. There is little an intruder can do other then try and get the heck out of there!
UPDATE: FlashFog just added a new section to their website specifically for School Security to help keep our schools safer from potential safety threats! So check it out: School Security Smoke Screen
I was a bit surprised by Gamo this year, they tend to stay away from actual Replica's and generally make BB/Pellet guns that look like popular guns but not any gun in particular. Gamo has a new BB/Pellet MP9 based machine pistol that uses a similar mechanism to their P-25 and PT-85 so it can shoot both 4.5mm BB's and .177 caliber Pellets using a double ended 16 shot rotary magazine. It also has an internal blowback system so it should have some recoil feel to it! I am pretty sure it is semi auto only but still a nice addition to their lineup!
Gamo also brought out a new 4.5mm BB Blowback pistol called the C-15 which has a metal slide and plastic frame, it kind of reminds me of the Umarex HPP in how it looks and feels.
Umarex had several new products that I am sure everyone is going to like! One that I think will do really well is the Steel Force, the Steel Force is designed around the 4.5mm BB shooting Steel Storm platform so it has a 6 round burst blowback operation and holds the 2x12 gram CO2 in the magazine while the BB's go in a 300 round hopper that feeds into a 30 round spring fed internal magazine. Like the Steel Storm it will shoot around 430 fps. The Steel Force has the advantage of being styled after the AR platform so it has a collapsible stock which will make shooting very easy.
Another often asked for airgun replica is the historic German Luger. This year Umarex stepped up to the plate and introduced the Umarex P.08 4.5mm BB pistol. Sorry, no blowback or even a working slide on this one but it is all metal and has a very good weight and feel to it.
If you're a fan of the entry level Umarex XBG then you may be interested in the new Umarex T.D.P. 45 which is very similar to the XBG in looks and features but with a slightly different look to it.
If you've ever wanted to turn your pistol into more of a PDW styled gun, you may be able to depending on which Umarex gun you have? Umarex added a very cool accessory called the T.A.C Converter that converts your Umarex HK USP (BB-Airsoft), SW MP40 (BB), XBG (BB), CZ Enforcer (Airsoft) and Walther P99 DOA (Airsoft) into more of a tactical (PDW) or Personal Defense Weapon complete with for-grip, adjustable rear sight, lots of rail options and a foldable stock.
I am assuming the Crosman M4-177 Pellet/BB Rifle has been doing well for Crosman as they have expanded with some more similar assault styled air rifles. The Crosman MSR77NP pretty much looks like a classic M16 but is in fact a Nitro Piston break barrel pellet rifle able to shoot .177 caliber pellets at 1200 fps (I hope there is a 499 fps Canada version planned too?).
A new takeoff of the M4-177 is the MK-177 which also shoots .177 caliber pellets and 4.5mm BB's using a multi-Pump System but it uses an upgraded more efficient pump system that squeaks out more fps with less pumps. The Crosman MK-177 is designed after the FN SCAR and is available in an adjustable iron sight version or a Red Dot equipped kit version.
One thing you can never get enough of in my opinion is another 1911 pistol! Crosman is introducing their GI Model 1911BB Blowback 4.5mm CO2 pistol, the one they had on hand was more of a prototype so the slide was not operational but it will feature an all metal design, blowback operation, 450 fps and a 20 round drop out magazine. I am sorry to say but it looks like the Crosman C51 has been dropped from Crosman's lineup but if you want a similar styled gun you can checkout the KWC SW40F which is a very close airsoft version.
We recently started carrying G&G Armament Airsoft guns, you can checkout my review of the Xtreme 45. I did stop by their booth and they had some new products on display, the M1 Grand (all wood stock) Airsoft had it's magwell all wrapped up as G&G had a propriety magazine system they did not want their competition to see. G&G also had some very interesting targets that light up, when shot they would react by individually turning off so you could see if you hit it or not.
There was a rather large crowd at the KWA booth but it was a shared booth so it's hard to say what everyone was looking at, the KWA area was pretty full, I did talk to the KWA rep and asked him point blank if KWC and KWA where the same or sister companies and the answer was not at all. There are often a lot of guns that look like they could be from the same company, I guess there is a lot of copying going on ;) One gun from KWA I would love to get my hands on is the Kriss SMG!
Now keep in mind many of these guns I have highlighted today are not available yet and a lot of them should be coming out in the spring time frame so please try to refrain from repeatedly asking when I will review them and have them in the store, it takes time and as much as we all want them now, they get here when they get here!
Watch my Vimeo video of the Replica Aiguns at SHOT Show Vegas 2013
