Entries in Revolver,Break Barrel

Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol Table Top Review

No Comments

Type: Pellet Pistol.
Distributer: Umarex.
Model: Ruger Mark IV.
Materials: Metal and polymer build.
Weight: 1.56 pounds (708 grams).
Barrel: 5.3 inches (135mm).
Total Length: 11 inches (279mm).
Propulsion: Spring Piston.
Action: SAO Break Barrel.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 1 round.
FPS: 320+.

Trigger Pull: The trigger pull on the Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.

Accuracy: I have not had the chance to really test fire this pellet pistol but will be doing so next week when I make my Field Test Shooting Video for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol. If it is anything like the Umarex Buck Mark URX which I imagine it will be, then I am expecting to get some good accuracy as the URX was able to get a nice under 1 inch shot grouping when I tested it a few years back. Velocity I am expecting to be up and over 300 fps even using lead pellets, I am hoping it will be in the mid 300’s

Build Quality: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?

Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.

Pros:

  • It's a decent Ruger Mark IV Replica!

  • Feels well built overall.

  • Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.

  • Barrel locks into place much better than the Umarex Browning Buck Mark URX did.

  • Fully adjustable rear sight with fiber optic front sight.

  • Auto locking safety, just don’t forget to unlock before each shot

  • Actual metal trigger in this version.

  • Nice and compact, not too heavy.

  • Full Ruger licensed via Umarex.

  • Fairly low price tag.

Cons:

  • No built in rail for a sight system like the Umarex Browning Buck Mark URX but this is tru for the Hunter version.

  • Trigger pull could be lighter to match the real steel version.

  • A bit more metal would have been nice to get the weigth up closer to the real steel version.

Comments:
I remember the Umarex Buck Mark URX being a super fun pellet pistol to shoot even though it is only a single shot airgun. Sometimes just getting back to the basics and taking your time to really place your shots and see how accurate you can be is more fun than spraying BB’s and pellets rapid fire and hoping you hit something. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is inexpensive to buy and inexpensive to shoot, no CO2, just a tin of your favorite pellets and you will get hours of fun for it while honing your shooting skills. And at the end of the day the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is not a bad Replica Airgun if you are a collector of shot guns.

My Vimeo Table Top Review Videos for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:

Categories: 4.5mm / .177 cal, Break Barrel, Pellet, Pistol, Review, Single Shot, Vimeo Video Tags: Ruger Mark IV, Ruger, Umarex

Umarex Ruger Mark IV - Action Army AAP-01 - Bear Desire XL - Crosman A4-P - Air Venturi Avenger Preview

No Comments

In this Preview Unboxing Vimeo Video I take a look at five very different products! A Spring Piston .177 Caliber Pellet Pistol, an Airsoft GBB Pistol, a Compact Crossbow, a full auto CO2 Blowback BB Pistol and a PPC .22 Caliber Pellet Rifle.

First up is the Umarex Ruger Mark IV Spring Piston Pellet Pistol which is a single shot replica pellet pistol that shoots .177 caliber pellets at up to 320 fps using a spring piston break barrel system. The Umarex Ruger Mark IV Spring Piston Pellet Pistol is a target plinker with fully adjustable fiber optic sights and should be a lot of fun to shoot!

Next I take a look at a Gas Blowback Airsoft Pistol from Action Army that closely resembles the Ruger Mark IV pistol with perhaps a more compact look. The Action Army AAP-01 GBB Airsoft Pistol is full blowback a full size drop out magazine and fiber optic sights. It also come with a threaded barrel and barrel extension for adding a longer barrel and much suppressor.

Next on my list of new items is the Bear X Desire XL Crossbow which is a 2.2 pound compact bolt shooting crossbow that sports a rail system with included adjustable iron sights that also allow for a red dot if you want to really customize it. The Bear X Desire XL Crossbow has a 60 pound draw and shoots arrows/bolts at up to 175 fps.

Another AR BB Rifle/Pistol from Crosman is the Crosman A4-P Full Auto CO2 BB Pistol which is essentially a pistol version of the AR Platform. If you like the Crosman DPMS SBR, R1, PDW then you will probably also like the Crosman AP-4. Like the others it uses dual CO2’s and shoots 4.5mm Steel BB;s in semi or full auto at 1400 rounds per minute until the 25 round magazine is empty.

Last included in this preview video is the Air Venturi Avenger Regulated PCP Pellet Rifle. I’m a bit uncertain about this one as I am pretty sure it is the non detuned PAL version that requires a firearms license here in Canada as it shoots at full velocity (.22 caliber pellet at 950 fps). If that’s the case then it will not be available in our Canada Replica Airguns Store but may be available in the US Replica Airguns Store. If it is the detuned version or a detuned version becomes available in Canada then I imagine we will at some point have it in the Canada replica Airguns Store. That said the Air Venturi Avenger Regulated PCP Pellet Rifle uses compressed air and shoots either .177. .22 or .25 caliber pellets using a latch system and rotary magazine.

Categories: .22 cal, 6mm, 4.5mm / .177 cal, Airsoft, Arrow, BB, Blowback, Break Barrel, CO2, Bulk Air, Crossbow, Full Auto, GBB, Gas, Non Airguns, PCP, Pellet, Pistol, Review, Rifle, Semi Auto, Slingshot, Spring Piston, Vimeo Video Tags: Umarex, Crosman, Air Venturi, Action Army, Bear River, M4-P, A4-P, Desire XL, APP-01, Ruger Mark IV, Avenger

Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle Field Test Review

No Comments

In this Field Test Shooting Video I put the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle through my standard Replica Airguns Indoor Field Test protocol by first testing out the velocity and placing 5 rounds through my Chronograph to see what the actual real world fps is using 14.3 grain lead pellets. I then setup a fresh paper target 30 feet downrange and place 10 pellets into it to see what type of grouping I can get. If you have not already watched my Table Top Video for this Break Barrel Spring Piston Pellet Rifle then make sure to do so for more details, specifications and close up video.

Starting off with my real world velocity test for the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle, I went with 14.3 grain lead pellets which are I would say on the heavier side. Even so I managed to hit 478 fps which produced a nice 7.26 foot pounds of energy which by the way is almost 10 Joules! If you are wondering about Canadian legalities, as long as I do not go over 500 fps AND go over 4.2 foot pounds (both thresholds must be exceeded), then this Airgun is considered a non-regulated firearm and does not require a firearms license.

Moving on to the accuracy portion of my Indoor Field Test in the Replica Airguns Sea Can. As always I placed a brand new paper target 30 feet downrange and proceeded to shoot ten 14.3 grain lead pellets from a rested and seated shooting position to allow for best possible results with as little human error but I am imperfect so some human error is always present. I was using the open fiver optic sights on the Webley Valuemax 22 Caliber Spring Piston Break Barrel Rifle rather than a scope even thought there is a dovetail rail with included scope stop. To be honest I was expecting a better grouping, something close to half an inch but on this day with this ammo choice I was closer to 1.5 to even 2 inches. I did see several pellets land in a tighter sub group but some came out of this group enlarging the grouping. I would like to try a different pellet choice to see if I can do better as I believe this rifle has way more potential.

In terms of power the Webley Valuemax 22 Caliber Spring Piston Break Barrel Pellet Rifle is about has high as you can go before it becomes a regulated firearm here in Canada so no complaints in that department. Again I was disappointed in the accuracy but I honestly believe a different pellet choice could fix that problem as I have seen often with other Pellet Rifles. Once the right pellet choice is made and granted a more consistent and tighter grouping is achieved, this Spring Piston Pellet Rifle could make a decent small pest control airgun!

Categories: 6mm, Break Barrel, Field Test, Pellet, Review, Rifle, Single Shot, Spring Piston, Vimeo Video Tags: Webley, Valuemax

Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle Table Top Revie

1 Comment

Type: Pellet Rifle.
Distributer: Webley & Scott.
Model: Valuemax.
Materials: Metal and polymer build.
Weight: 6.4 pounds (2900 grams).
Barrel: 17.7 inches (450mm), rifled.
Total Length: 43 inches (1092mm)
Propulsion: Spring Piston
Action: Break Barrel.
Ammunition Type: .22 Caliber Pellets.
Ammunition Capacity: Single Shot.
FPS: 499.

Trigger Pull: The trigger pull on the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is fairly nice There is a little bit of very light take up followed by a vert light release , the take up or travel length can be adjusted on this Air Rifle but that is the only trigger adjustment you can make and perhaps all that is needed.

Accuracy: I have not performed my Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle but I did get to take around 20 or so shots with it when I was trying to get it to diesel for me. It looks ot me like it is going to be nice and accurate as I was not even really going for accuracy and it seemed to already be grouping fairly tight. I was recoding fps using my Chronograph as I was trying to find out if by adding some oil to the spring piston chamber could get it to diesel which it never did for me, I was however to establish that the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle shot right around 470-480 fps using 14.3 grain lead pellets which worked out to right around 7.32 foot pounds of energy. I will know a lot more when I do my official Field Test Shooting Video next week.

Build Quality: Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is built to be a value priced Airgun hence the name (Valuemax), that said it is maid well enough with lots of metal and of course some plastic or in this case mostly nylon as the stock is a solid nylon piece. Other than the stock the plastic parts are found to be in the sights and trigger guard, everything else seems to be metal.

Realism: The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not a replica or copy of any real steel gun in production but it does look like a traditional hunting rifle in basic shape so make sure to transport thank airgun as if it was a real gun. Either in a gun case or perhaps a blanket in your trunk and always obey any laws for gun position and transportation in your area.

Pros:

  • Inexpensive price tag for well made decent performer.

  • Initial test showed to have good accuracy and power! (more to come).

  • Fully adjustable sights with optical TRUGLO Fiber Optics.

  • Can add a magnified optical scope using the top built in dovetail rail.

  • Nylon fiber stock is durable and functional with the addition of a vented rubber buttplate.

  • Trigger feels decent and is also adjustable for travel length.

  • Rear thumb safety resets after each break of the barrel.

  • Nice light and short single action trigger.

  • Would be good for small pest control because of decent FPS and good accuracy.

Cons:

  • Included sights are mostly plastic.

  • The Valuemax version has a more basic less adjustable trigger.

  • Detuned down to under 500 fps for Canada import as non-regulated Firearm.

Comments:
I am looking forward to performing my Indoor Field Test Shooting Video for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle to see what it can really do in terms of accuracy so stay posted for that video next week. Overall if you are lucky enough to already have one or can get your hands on one since this rifle is discontinued in some area, I think this is a great Break Piston Air Rifle especially if you live in Canada and want the most bang for your buck. I am not only talking about cost verses features, I also mean power and energy since the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is a .22 caliber Air Rifle that can shoot really close to 500 fps with a nice heavy grain lead pellet achieving decent energy levels reasonable enough for small pest control. The Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle is not feature less, it does include a reseting safety, anti bear trap system, dove tail mounts with an included scope stop, fiver optic adjustable sights and a vert ergonomic textured nylon stock. All in all great value for what you pay!

My Vimeo Videos for the Webley Valuemax .22 Caliber Spring Piston Break Barrel Rifle:

Categories: .22 cal, 6mm, Break Barrel, Pellet, Review, Rifle, Single Shot, Spring Piston, Vimeo Video Tags: Webley, Valuemax

Umarex Mod 92 A1 and 1911 Tac Airsoft - Barra Schofield Steel BB Pistol Update Video

No Comments

In this Vimeo Replica Airguns Update Video I take a look at three CO2 Airguns, one is a 4.5mm Steel BB revolver distributed by Barra and two are CO2 Blowback Airsoft Pistols distributed by Umarex. All of these CO2 Airguns I have previously reviewed in slightly different versions either barrel length and finish or Steel BB as compared to 6mm Airsoft So checkout why other reviews on similar version Airguns.

The Barra Barra Schofield CO2 BB Revolver is a replica of the Schofield No. 3 single action revolver and utilizes 6 reloadable shells for a very realistic shooting experience. It is very solid in construction bing made mostly out of metal and weighs in at around 2.4 pounds. This version shots 4.5 mm Steel BBs at a velocity of up to 400 fps. It comes in a variety of barrel lengths and finishes so amen sure to have a look in our Online Replica Airguns Store for what we have available

Next up from Umarex is the fully licensed Beretta Pietro Mod. 92 A1 CO2 Blowback Semi and Full Auto Airsoft Pistol, this product is distributed by Umarex but is made by KWC. Another solid metal pistol with a hefty 2.4 pound weigth that holds 21 rounds in its full size drop out metal magazine and offers both semi and full auto shooting at the flick of a switch!

Again from Umarex I showcase the Elite Force 1911 Tac CO2 Blowback Airsoft Pistol and like the Beretta Pietro it too is made in the KWC factory for Umarex. The 1911 Tac as the name suggest is a tactical version of the standard Colt 1911 but with some upgrades like a skeletonized hammer and trigger along with an ambidextrous safety, white dot sights front and back and a picatinny rail on the frame for add ons. You can expect velocity to be somewhere in the 400 fps range and the full size drop out metal magazine holds 15 Airsoft BB’s.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Full Auto, Pistol, Review, Repeater, Revolver, Semi Auto, YouTube Video Tags: Barra, Schofield No. 3, Bear River, Umarex, Beretta Mod. 92 A1, Beretta, 1911, M1911, 1911 TAC

Crosman Vigilante CO2 Pellet and BB Revolver Field Test Review

No Comments

In this Field Test Shooting Video I test out Crosman’s latest version to the 357 line of CO2 Revolvers and perform both my Velocity and Accuracy test using both .177 caliber Lead Pellets and 4.5mm Steel BB’s to see which ammo has better velocity/power and is most accurate. Also make sure to watch my Table Tope Video Review where I go ver specifications and features and show the Crosman Vigilante CO2 Pellet and BB Revolver up nice and close.

Starting with the velocity portion of my Indoor Field Test Shooting video I placed a brand new 12 gram CO2 into the Crosman Vigilante CO2 Pellet and BB Revolver and tested out some 7 grain .177 caliber Lead Pellets. I was able to average 389 fps in what I would consider normal indoor temperature ranges so you can expect a bit higher velocities in outdoor weather conditions. Moving on the 4.5mm 5.1 grain Steel BB’s, I averaged a bit lower at 360 fps which may seem confusing since the Steel BB’s are lighter than the Lead Pellets? The Lead Pellets fit the barrel much more snug stoping any CO2 from getting around them which helps increase the fps over the Steel BB’s which are a hard metal and need to be slightly smaller in diameter and therefore do let some CO2 get by reducing the pressure behind them.

For my accuracy porting of the the Indoor Field Test I was going to place 6 shots from each magazine into my paper target setup 30 feet down range but ended up using all 10 rounds for the pellet magazine, perhaps because I was just having too much fun :) Since the BB magazine only holds 6 rounds my shot grouping for BB’s only included 6 shots so keep that in mind for the final results. All said and done the Lead Pellets outperformed the Steel BB’s once again getting about a 1.5 inch grouping over the 2.5 inch grouping for the Steel BB’s. And I know the Crosman Vigilante CO2 Pellet and BB Revolver is more than capable of getting a .5 to 1 inch grouping from previous Field Tests I have made using similar 357 type Crosman Revolvers.

The Crosman Vigilante CO2 Pellet and BB Revolver is just one of those must have old school classic Air Pistols I think everyone should own at least some sort of version of. I do like the look of the Vigilante barrel with it’s more modern and aggressive design and functional top and bottom rails for adding on accessories. The ability to choose what ammo type you want to shoot is also a plus and the price point is bang on for a nice CO2 Air powered Revolver.

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Crosman, Vigilante, 357

Crosman Vigilante CO2 Pellet and BB Revolver Table Top Review

No Comments

Type: Pellet & BB Revolver
Manufacturer: Crosman
Model: Vigilante
Materials: Metal and Plastic.
Weight: 2 pounds (908 grams).
Barrel: 6 inches rifled.
Length: 11.36 inches.
Propulsion: CO2 x 1
Action: Revolve , single and double action trigger.
Ammunition Type: 4.5mm Steel BB's / .177 caliber Pellets.
Ammunition Capacity: 6-BB / 10-Pellet round rotary magazines.
FPS: 465-BB’s / 435-Pellets.

Trigger Pull: The trigger pull on the Crosman Vigilante CO2 Pellet and BB Revolver is rather nice in single action with virtually zero take-up and it has a not too light weight with a predictable feel to it. In double action it does get much longer and heavier but still very usable. If you have larger thicker finger then you may want to start off in single action as the finger opening is a bit tight.

Accuracy: I have not specifically tested out the Crosman Vigilante CO2 Pellet and BB Revolver so far but I would be very surprised if it was any different than the standard Crosman 357 I tested back in 2012. Other than the shape of the outer barrel, both of these guns are virtually the same including the frame and the 6 inch barrels. Back in 2012 when I tested out the Crosman 357 I averaged 402 fps using 6.9 grain pellets and was able to get a 1 inch multi-shot grouping at 30 feet away from my paper target. Not sure if this was the entire 10 round mag or not? I will be making an update Field Test Shooting Video so we will see if I can replicate these results with the Crosman Vigilante CO2 Pellet and BB Revolver.

Build Quality: The Crosman Vigilante CO2 Pellet and BB Revolver is a fairly basic pistol that incorporates a plastic outer barrel and inner steel barrel, the grips are also plastic as expected and so are the magazines and sights. Most everything else is metal including the receiver, trigger and hammer. This line of Crosman 357 pistols has been around for decades so you can expect hours of fun and reliable shooting with it.

Realism: There are for sure a lot more realistic looking Revolvers out there with swing out cylinders that except shells just like their real steel counterparts but where the Crosman Vigilante CO2 Pellet and BB Revolver shines is in performance. You will get more shots per CO2, higher fps and better accuracy with the Crosman Vigilante CO2 Pellet and BB Revolver over other more realistic Revolvers on the market.

Pros:

  • Inexpensive Pellet revolver with a proven track record that goes back decades.

  • Good usage of metal parts where you need them most. (Metal  trigger, hammer, frame, barrel, CO2 Tab screw

  • Single and double action trigger for action and more focused shooting.

  • Excellent accuracy and good power with a reasonable amount of shots per CO2.

  • Fully adjustable rear sight.

  • Can mount a bunch of accessories on the picatinny barrel top and bottom rails.

  • CO2 and CO2 tab are nicely hidden and use all metal.

  • Comes with both a Pellet and BB magazine.

Cons:

  • Outer barrel is plastic but very solid. Metal would have added a bit more weight and perhaps better balance?

  • Grips and trigger pull length may be a bit long for smaller handed people when shooting in double action.

  • Not your most realistic revolver in terms of replicas out there but I would say more usable than most.

  • No white dots on the sights.

The Crosman Vigilante CO2 Pellet and BB Revolver is basically a reskinned Crosman 357 at the end of the day but I have to say it is my favorite looking Crosman 357 out there with its aggressive barrel design. And the added bonus are the top and bottom Picatinny rails which make for mounting accessories like Red Dots, Lasers and Tac Lights super easy! if you’re looking for function over realism at a price point that is more than fair then pick yourself up one of the Crosman Vigilante’s from our Replica Airguns Store!

Categories: 4.5mm / .177 cal, BB, CO2, Comparison, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Crosman, Vigilante, 357, Colt Python 357

Bill C-21 Let's All Make Some Waves

1 Comment

I made a video a little bit ago talking about how Canada’s new Bill C-21 will affect pretty every gun owner in Canada including even airgun owners of BB, Pellet Airsoft and even Paintball Guns. Make sure to watch that video first called Bill C-21 Canada is Going After Your Red Ryder BB Gun.

This video is all about how you can get involved in making some waves by signing two online petitions along with contacting your local Member of Parliament and letting them know your disapproval of Bill C-21 and all that it imposes on law abiding Canadian gun owners.

Probably the most important online petition to sign would be the House of Commons Petition E-3201 Bill C-21 so make sure to sign that one!

The other online e-petition we need to sign is the change.org petition.

And lastly but also super important is to send an email to your local member of Parliament again let them know your disapproval of Bill C-21. I have included a link to the web[age where you can locate your local MP and below that is a template of what you could include in your email to them.

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

Dear (MP),

I am a constituent in your riding. I am writing to you to voice my concerns over the new provisions that were announced under the proposed Bill C-21, and how this will impact myself, my community and many other Canadians.

"Criminal Code 1 (1) The definition replica firearm in subsection 84(1) of the Criminal Code is replaced by the following:

replica firearm means any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm; (réplique)

(2) Section 84 of the Act is amended by adding the following after subsection (3.1): Certain firearms deemed to be prohibited devices

(3.2) For the purposes of sections 99 to 101, 103 to 107 and 117.03, a firearm is deemed to be a prohibited device if

(a) it is proved that the firearm is not designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second or at a muzzle energy exceeding 5.7 Joules; and (b) the firearm is designed or intended to exactly resemble, or to resemble with near precision, a firearm, other than an antique firearm, that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules."

Categories: Airgun News, Airsoft, Airsoft News, Blank Gun News, Blank Gun, BB, Gun Law, Gun Safety, Non Airguns, Paintball, Pellet, Pistol, Real Gun, Replica Airguns News, Revolver, Rifle, YouTube Video Tags: Bill C-21

BB - Pellet - Airsoft - Paintball Pistol Power and Accuracy Test

No Comments

I often have people ask me what is more powerful in terms of one gun over another and which Airguns have more raw power, BB versus, Pellet, versus Airsoft, versus Paintball?

Well in this indoor field test shooting video I compare all of the above head to head to see which Airgun not only has the most raw power but also how well they perform on a target setup 30 feet down range since after all what does it matter how powerful a gun is if it can not hit the target!

The Airguns I used in this head to head shooting performance test where as follows:

Keep in mind the ammunition for each Airgun is very different not just in terms of materials but also their weight which will have a big effect on the energy they produce. For example for this test I used 4.6 grain 4.5mm Steel BBs, 4.6 grain 6mm Aluminum Airsoft BB’s. 6.9 grain .177 cal. Lead Pellets and 17.7 grain .50 cal. Rubber Paintballs.

Watch my YouTube Video to see how well each Airgun did in this comparison shooting test!

Categories: .50 cal, 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, Field Test, Paintball, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Umarex, T4E TR50, Desert Eagle, EKOL, ES 55, Cybergun

Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver Field Test Review

3 Comments

Perhaps you might call this a followup video since I already made a full Field Test Shooting Video of the all black version of this pistol and you may wonder if the color of a gun could in some way effect how it performs? Well I don’t think color would really matter but it has been over 6 years since I did my original Field Test Shooting video fo the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver and so perhaps some things have changed, maybe my shooting is better or worse? At any rate let’s find out.

Also make sure to take a look at my Table top Video for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver if you're interested in the specifications and details along with some nice tight close up video of the Airgun.

Starting off with my Chronograph test I was able to get an average 6 shot velocity of 348 fps which is about 40 fps less than my testing 6 years ago of 390 fps, perhaps the temperatures where a bit different? Perhaps the valve setups of the guns was not the same? By the way the temperature was 23 degrees Celsius in the indoor Airgun Sea Can Shooting Range and I was using a brand new 12 gram CO2 along with 5.1 grain zinc coated steel BB’s.

Moving on to the accuracy test, surely I would get a similar 1 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver, after all it’s been 6 years and I must be a much more advanced shooter… Well there again the Chrome Umarex Colt Python 357 Magnum CO2 BB Revolver did not perform as well as the black one from my 2014 Field Test? Again maybe the steel BB’s I was using where not of the same quality? Maybe I simply had one too many espresso shots? As the video shows this time around I was only able to get about a 2 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver. Still not bad but I was hoping for better result or at least the same as before.

I could do this test again and get completely different results using perhaps another brand of CO2 on a warmer day with higher quality Steel BB’s and just maybe with me on my game a little bit better? At the end of the day 350 fps is perfectly fine for putting holes in pop cans and a 2 inch group at 30 feet will get you on most targets every time so I’m not going to sweat it too much. If you are looking for a shell loading CO2 BB Revolver the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is for sure one of my top picks.

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, YouTube Video Tags: Umarex, Colt Python 357, KWC, 357, Colt

Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver Table Top Review

6 Comments

Type: BB air revolver
Manufacturer: Umarex.
Model:  Colt Python 375
Materials: Almost entirely all Metal.
Weight: 2.75 pounds (1218 grams).
Barrel: 5.5 inches, metal non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 round cylinder.
FPS: 400.

Trigger Pull: The trigger pull on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is good in both single and double action, it’s nice that you have the shorter lighter single action trigger for slower more accurate shooting but you can also blast away in double action when you feel like it. The hammer on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is firm with not very much wiggle which some other revolvers in this category do have.

Accuracy: Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver being mostly metal has a very good build quality and is on par with the Dan Wesson 715 shell loading revolver. It has a nice weigth adn balance to it and feels really good in the hand! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time compared to the black finishes fodun on most KWC made Airguns.

Realism: TheUmarex Colt Python 357 Magnum Chrome CO2 BB Revolver overall is a close copy a the real steel Colt Python 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that, this pistol is super close to the original Colt Python 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands and noise to be had.

Pros:

  • Shells loading revolver give you the feeling of loading and shooting a real revolver.

  • Mostly all metal design.

  • Lots of detail, well made, chrome looks nice, not sure if it will wear better than the black finish found on most KWC made pistols?

  • Good overall weight, almost 3 pounds.

  • Should have good overall power, accuracy and shots per CO2 (based on my previous Colt Python testing).

  • Fully adjustable sights.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Nice Trigger pull in both single and double action.

Cons:

  • Grips are a bit rough and wood grain is only OK.

  • Grips may be a bit large for people with small hands.

  • Decent enough Colt Python 357 replica but the frame is a bit long between the cylinder and the hammer.

Comments:

It’s been a while since I reviewed a Shell Loading Airgun and this one is pretty much the same Airgun I have reviewed in the past in both the KWC and Umarex Distributed forms. It has been almost 6 years since I took a look at one on my table and it still hods up today. I plan on performing another Field Test Shooting Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver to see if I can replicate the same good results I did back in 2014 when I tested it out on my deck. If you’re looking for a shell loading revolver in the 357 design then for sure checkout the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver as an option.

My Vimeo Table Top Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver:

Categories: 4.5mm / .177 cal, BB, CO2, Pistol, Review, Revolver, YouTube Video Tags: Umarex, 357, Colt Python 357, KWC

Gamo PR-776 CO2 .177 Caliber Pellet Revolver Table Top Review

No Comments

Type: Pellet Revolver.
Manufacturer: Gamo
Model: PR-776.
Materials: Mostly metal construction.
Weight: 2.2 Pounds (1 kg).
Barrel Length: 6 inches
Total Length: 11.5 inches.
Propulsion: CO2 x1
Action: Revolver single and double action.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 8 rounds per magazine.
Max FPS: 400+ fps.

Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.

Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.

Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.

Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.

Pros:

  • Good power over 400 fps using actual lead pellets.

  • Quicker reloading over shell loading revolvers

  • More shots per magazine reload, 8 versus 6.

  • Comes with two metal 8 round magazines.

  • Traditional single and double action trigger.

  • White dot front sight with fully adjustable rear sight.

  • Good weight and feel to it.

  • Fit and finish look good.

  • Recessed barrel for realistic looking barrel opening.

  • Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.

Cons:

  • Not a fan of the loose pistol grip setup to access the CO2.

  • Was hoping to get a bit tighter grouping but may have been a pellet choice issue.

Comments:
It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.

My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:

Categories: 4.5mm / .177 cal, CO2, Comparison, Pellet, Pistol, Review, Revolver, YouTube Video Tags: Gamo, PR-776

Gamo PR-776 CO2 .177 Caliber Pellet Revolver Field Test Review

No Comments

Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.

For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.

For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.

The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.

Categories: 4.5mm / .177 cal, CO2, Pellet, Pistol, Review, Revolver, YouTube Video Tags: Gamo, PR-776

Gamo PR-776 - Gamo P-900 - REKT OPfour - JAG Arms Scattergun Preview Video

No Comments

Gamo PR-776 CO2 Pellet Revolver

  • .177 caliber Pellets

  • 8 round rotary magazines x2

  • 12 Gram CO2 x1

  • 6 inch rifled barrel

  • Fixed white dot front, fully adjustable rear sight

  • 2.29 pounds

  • 400 fps

  • Buy in Canada

  • Buy in the US

Gamo P-900 IGT Pellet Pistol

  • .177 caliber Pellets

  • Break Barrel single shot

  • Gas piston (IGT)

  • 6.25 inch rifled barrel

  • Fiber optic front, adjustable rear sight

  • 1.3 pounds

  • 400 fps

  • Buy in Canada

  • Buy in the US

Umarex REKT OPfour CO2 Dart Rifle

  • Nerf Darts 30% faster / 30% farther

  • Pump action

  • CO2 x2

  • 12 round removable magazine

  • Peep sights

  • Adjustable rear stock

  • 90 fps

  • Buy in Canada

  • Buy in the US

JAG Arms Scattergun Green Gas Airsoft Shotgun

  • 6mm Airsoft BB’s

  • 28 round shotgun shell magazines x6

  • Green gas or propane

  • Pump action 3 /6 round burst

  • Pop-up front and back iron sights

  • 6-7 pounds

  • 360 fps

  • Buy in Canada

  • Buy in the US

Categories: 6mm, 4.5mm / .177 cal, Airsoft, Break Barrel, CO2, Gas, Pellet, Pistol, Pump, Review, Revolver, Rifle, Semi Auto, Single Shot, YouTube Video, Spring Piston Tags: Umarex, Gamo, JAG Arms, P-900, PR-776, REKT, REKT OPfour, Scattergun SPX2, Nerf, Gamo P900, P900

Umarex T4E TR50 .50 Caliber Paintball Revolver Field Test Review

No Comments

If you have not already checked out my Table Top Video for the Umarex T4E TR50 .50 Caliber Paintball Revolver then make sure to do so for specifications and a closer look at it.

The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball pistol, it has a very different look and also uses .50 caliber Paintballs which are a little bit less common than the .68 and .43 caliber paintball gun I have been reviewing up until now. The Umarex T4E TR50 .50 Caliber Paintball Revolver is some countries is marketed as a self defense gun but those versions do have a little bit more fps and foot pounds of energy. The version I am testing is not marketed here in Canada or the US as self defense products but rather as more of a training Paintball Gun.

Starting with my Chronograph velocity test I placed 5 Rubber Balls through my Chronograph using a brand new CO2. The Rubber balls I am going to say are a little bit heavier than standard Paintballs and Umarex claims the Umarex T4E TR50 .50 Caliber Paintball Revolver is capable of hitting around 360 fps so with the heavier rubber balls I was expecting a little bit under the max fps. I was able to get an average of 328 fps so not bad at all.

Moving on to my accuracy test. I need up placing 10 of my 12 rounds into the paper target as I had two rounds that went off in what I am going to call an uncontrolled manor. The 10 rubber paintball rounds that did hit my paper target that was setup 30 feet down range all hit within about 6 inches of each other daily well centered left and right and a little bit low on the target. Gettin back to the uncontrolled shots, I had a situation where I pulled the trigger and the Umarex T4E TR50 .50 Caliber Paintball Revolver went click as you would expect but no CO2 was expelled and so no round was shot. I thought perhaps the cylinder was caught up so I went to wiggle it to try and free it up. As I did so the gun went off without my finger anywhere near the trigger. I am glad I was using rubber balls since the rubber ball hit my cabinet leaning a biota a mark but really causing any damage. This happened twice with the same cylinder, the second time I was bit more prepared for it and had the gun pointed well downrange. I was not able to recreate this problem again so perhaps the cylinder magazine was not seated properly but this still concerns me a bit.

Overall I really like the Umarex T4E TR50 .50 Caliber Paintball Revolver, it’s a pretty cool looking Paintball Gun with decent accuracy and power, you can even feel a little push back and barrel lift when you shoot it. I also like that you can preload a CO2 and puncture it whenever hypo are ready to shoot with a quick smack on the bottom of the grip. Just made sure to put the CO2 in the right way :)

Categories: .50 cal, CO2, Field Test, Paintball, Pistol, Review, Revolver, YouTube Video Tags: Umarex, T4E TR50, T4E

Rx Target Systems Field Test Shooting Video

No Comments

It was a pretty nice day today so I got outside and tested out the Rx Target Systems to see how well it worked shooting my Sig Sauer Virtus PCP .22 Caliber Air Rifle at it for about 50 feet down range.

My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.

I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.

Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.

We hope to have the Rx Target Systems in our Canada and US Online Replica Airguns stores in the near future but until them you can concat Rx Target Systems at their website.

Categories: Accessory, Airsoft, BB, Pellet, Pistol, Review, Rifle, Revolver, Spring Piston, YouTube Video Tags: Rx Target Systems, Sig Sauer Virtus

Rx Target Systems Preview Video

No Comments

I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.

For now here are some of the key points I want to get out to everyone:

Mission:
Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack.  What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.

Modular 

  • One base allows interchange of faceplates for different target configurations 

  • One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles 

Portable 

  • Mount it on a shelf indoors 

  • Mount it on a sawhorse outdoors  

  • Carry it in a backpack or duffle bag- its 10 pounds 

Rugged 

  • Solid steel design 

  • Faceplates from 10 gauge to ¼ inch thick 

3-Dimensional 

  • Faceplate is offset from paddles 

  • Clipping the aperture does not guarantee a score 

Intentions of target configurations 

  • Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull) 

  • 1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper 

  • AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.  

  • WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures 

  • 10-15- Inspired by customer request, uses 10mm and 15mm apertures.  High-Precision shooting.

Categories: .20 cal, .22 cal, 4.5mm / .177 cal, 6mm, Accessory, Airgun News, Airsoft News, PCP, Pellet, Pistol, Pump, Replica Airguns News, Review, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags: Rx Target Systems

Chiappa New Rhino Airgun at Show 2020 Las Vegas

No Comments

chiappa-firearms-vector-logo.png

This isn’t a SHOT Show 2020 Interview but most certainly worth reporting on. While walking around SHOT Show I ventured into the Chiappa Booth as I own a .22 caliber 1911 styled pistol from them and they do have some interesting products to take a look at.

Then I saw a red tip on one of their Chiappa Rhino Revolvers which caught my eye since I was not aware that Chiappa was making an Airgun version of their Rhino. Well as it turns out they are hoping to be shipping both an Airsoft version and Steel BB version around spring time and from what I can tell there will be two finishes, a kind of Gold Satin finish and also a Back finish version. As is with a lot of revolvers these days they will be shell loading which will help them look the part of a real steel Chiappa Rhino Revolver.

Looking forward to getting my hands on one when they come out in Spring this year!

Categories: 4.5mm / .177 cal, 6mm, Airgun News, Airsoft, Airsoft News, BB, CO2, Pistol, Replica Airguns News, Revolver, YouTube Video Tags: Chiappa, Rhino, SHOT Show, SHOT Show 2020

Air Venturi SHOT Show 2020 Las Vegas Interview

No Comments

air-venturi.png

In this SHOT Show Las Vegas 2020 Interview Video Scott takes us through a range of new products from Air Venturi.

Scott and I talk about the Air Venturi TR5 and how it came about to fill the hole the Baikal MP-61 left behind. We also talk a look at some new Air Rifles, a pumper called the Butterfly with a super cool linkage based system that makes pumping a lot easier. A PCP side lever cocking Air Rifle that I’m not even sure has a name yet but will be available in .177 .22 and .25 caliber pellet for around $299 US.

The only Air Venturi replica we looked at is a new Springfield Armory under lever Spring Piston Air rifle modeled after the M1A. Last up Scott went showed us how the Bada Bang targeting system is shaping up and looks to be almost ready for production.

Categories: .22 cal, 4.5mm / .177 cal, Airgun News, Break Barrel, Multi-pump, PCP, Pellet, Pump, Replica Airguns News, Rifle, Single Shot, Spring Piston, YouTube Video Tags: AirVenturi, SHOT Show 2020, SHOT Show