It took me a bit to get to this Field Test Reviews done for both the Arcturus AK05 AK AEG and Arcturus AK06 AK AEG Airsoft Rifles but I finally made them! if you want more specifications and details along with closeup video of the Arcturus AK05 then make sure to checkout my Table Tope Review Video for it. In this video I will be testing out the Velocity and then move on to the Accuracy for this AEG Airsoft Rifle in both semi and full auto conducted in the Replica Airguns Sea Can Indoor Airgun Range.
First I placed 5 rounds through my Chronograph shooting .20 gram Airsoft BB’s and I found the Arcturus AK05 AK AEG Airsoft Rifle to be on the higher fps range and it was very consistent with the fastest shot hitting 401 fps and the slowest shot hitting 393. This average an impressive 398 fps which could be a bit hot for some Airsoft Game shooting situations, but perhaps ideal when shooting outdoors at longer ranges.
I then placed a fresh paper target up 30 feet down range and proceeded to shot 10 rounds into the target using a seated and rested shooting position. I followed this up with a spring full of BB’s in full auto in semi auto and full auto getting a bit tighter group in semi auto then I did in full auto but this is generally the case. I did have a bit of trouble with the magazine not loading Airsoft BB’s even though I did tighten the spring fully between testing. Perhaps the magazine needed some break in time or was even defective? Out of the box the Arcturus AK05 AK AEG Airsoft Rifle shot very close to the bullseye but just a tad to the left but not by much. The sights are adjustable for elevation if need be, or you can put a compact red dot sight on the rail for spot on accuracy.
I really did like the Arcturus AK05 AK AEG Airsoft Rifle as it performed very well for me in terms of both power and accuracy other then the magazine acting up. I would most likely add a compact red dot sight on the rail as the built in sights are limited in terms of windage adjustments. You can also see in this video that I had to take off the top dust receiver cover in order to place the battery in it, you will need a very specific and compact battery in order to have it installed and be able to close the top cover. Those two things aside the Arcturus AK05 AK AEG Airsoft Rifle is a great choice if you are looking for a compact and more modernized AK type AEG Airsoft Rifle. Also make sure to watch my Arcturus AK05 AK AEG Airsoft Rifle Field Test Review already available to view on Vimeo!
It took me a bit to get to this Field Test Review for the Arcturus AK06 AK AEG Airsoft Rifle but here we are, if you want more specifications and details along with closeup video of the Arcturus AK06 then make sure to checkout my Table Tope Review Video for it. In this video I will be testing out the Velocity and accuracy in both semi and full auto here in the Replica Airguns Sea Can Indoor Airgun Range.
First off I placed 5 rounds through my Chronograph shooting .20 gram Airsoft BB’s and I found the Arcturus AK06 AK AEG Airsoft Rifle to be very consistent with the fastest shot hitting 370 fps and the slowest shot hitting 368, this average an impressive 369 fps which is perfect for most Airsoft Gam shooting situations.
I then placed a fresh paper target up 30 feet down range and proceeded to shot 10 rounds into the target using a seated and rested shooting position. I followed this up with a spring full of shots in full auto with semi auto and full auto getting pretty much the exact same results which I would say to be about a 1.5-2 inch grouping. Out of the box the Arcturus AK06 AK AEG Airsoft Rifle did shot a bit high making me aim about 6 inches lower to achieve hits in the bullseye. Perhaps hope could remedy this as the sights are too adjustable…
I really did like the Arcturus AK06 AK AEG Airsoft Rifle as it performed very well for me in terms of both power and accuracy. I was not a fan of the built in sights as the notch in the back was so low that it barely lined up allowed for it to be inline with the front post sight, I kind of had to guess where the notch was to make it work. I would for sure put a red dot on the rail as the built in sights are pretty much useless. you can also see in this video that I had to take off the top dust receiver cover in order to place my battery in it, you will need a very specific battery in order to have it installed and close the top cover. those two things aside the Arcturus AK06 AK AEG Airsoft Rifle is a really great AK Staled AEG Airsoft Rifle in my books stay tuned for my Arcturus AK05 AK AEG Airsoft Rifle Field Test Review coming soon!
I First off this Field Test Shooting Video Review for the Umarex HK P30 AEG Full Auto Airsoft Pistol is going to be more like reviewing a NERF gun, well at least in terms of performance. I do however test it out just like I test all Airsoft Pistols by shooting 5 rounds through the Chronograph to see what the average velocity is in fps. Then I shoot some rounds at a paper target setup 30 feet downrange to see how accurate the Umarex HK P30 AEG Full Auto Airsoft Pistol is. If you want more specification and details along with some nice close up video of the Umarex HK P30, then checkout my Table Top Video for it.
OK, so starting with velocity, I have to say it shot well below the claimed 180fps on the clamshell packaging, keep in mind this is for .12 gram Airsoft BB’s and I was using .20 gram Airsoft BB’s so almost twice as heavy which should mean about half the speed and that’s about what I got. I was able to get an average fps of 95 with my slowest shot hitting 94 fps and my fastest shot hitting 96 fps so very consistently slow :)
What about accuracy? Could the mighty Umarex HK P30 AEG Full Auto Airsoft Pistol at least redeem itself here… Well not really! It was hard to fully determine exactly where my shots where hitting the paper target as it seems 95 fps is not powerful enough to even penetrate the paper. All I could do was put little dings in the paper which are bit hard to make out. My best guess is I should be able to hit a standard sheet of paper at 30 feet away once I figure out where the center point is. I was shooting at the bullseye and hit most shots rather low on the target with several of them being too low to get on the paper. In full auto things did not get much better, but full auto with this little pea shooter is kind of fun, so just keep the selector on full auto all the time… I would!
Getting back to the Umarex HK P30 AEG Full Auto Airsoft Pistol being more like a NERF gun, I say this because it is way too underpowered to use in any Airsoft wars as people probably won’t even know they got hit! But perhaps it is just perfect for indoor NERF type shootouts? I can’t see the Umarex HK P30 doing any type of damage to your surroundings or to yourself but always make sure to wear eye protection when shooting as even an eye lash can feel like murder in the eye let alone a 6mm Airsoft BB. The only real downside I can see to using the Umarex HK P30 AEG Full Auto Airsoft Pistol indoors like a NERF gun would be the cleanup of all the microscopic Airsoft BB’s, you will probably be finding them under furniture and in crazy spots for months afterwards. All in all, the Umarex HK P30 AEG Full Auto Airsoft Pistol may just be perfect for some indoor fun on those rainy days!
Type: BB air pistol. Manufacturer: Umarex USA. Model: HK P30 Materials: All pastic outer shell. Weight: .5 pounds (227 grams) Barrel: Metal non-rifled 4.25 inches (106mm). Total Length: 7 inches (178mm) Propulsion: CO2 x 1. Action: Semi & full auto blowback, single action only. Ammunition Type: 6mm Plastic Airsoft BB's. Ammunition Capacity: 16 round plastic curved stick magazine x2. FPS: 180 Rate of fire: 200 shots/min.
Trigger Pull: The trigger on the Umarex HK P30 AEG Full Auto Airsoft Pistol is electric as it is an AEG Pistol that requires batteries to operate. The trigger is basically an ON/Off switch that activates the blowback which also seems to create the pressure to propel an Airsoft BB. Mind you not all that fast but fast enough for perhaps a more safe indoor/basement type Airsoft war? Getting back to the trigger pull I would say it is light but on the ing side for an AEG.
Accuracy: You will have to stay posted for my proper Field Test Shooting Video for the Umarex HK P30 AEG Full Auto Airsoft Pistol. That said I did pop off a magazine of BB’s (16 rounds), some in semi auto and some in full auto. Do not expect this Airsoft pistol to be all that powerful as it can barely penetrate a paper target. I was expecting the cycle rate of full auto to feel slower than it actually shot so that’s a good thing! I see this as almost an alternative to a nerf gun but using Airsoft BB’s. Do this at your own risk and please use proper eye protection. I can not comment too much on accuracy as I was just pointing and shooting to get a basic feel for the gun.
Build Quality: The Umarex HK P30 AEG Full Auto Airsoft Pistol is a low cost all plastic Airsoft pistol which kind of says it all. Being super light weight means if you drop it, chances are it will be fine because it is so light weight. Fit and finish are decent but without seeing what’s inside I can only guess at how long it will last.
Realism: The Umarex HK P30 AEG Full Auto Airsoft Pistol is a true licensed replica via Umarex. It is about the right shape and size as a real HK P30 and other than the orange tip could fool most people unless really close up to it and of course holding it. It also has a kind of out of place grip safety on the front which is not an HK attribute. Being an AEG with batteries in the grip there is no full size magazine and again as it is all plastic it does not have nearly the same weight as a real HK P30. The only working mechanical parts are essentially the trigger, grip safety and selector switch in the trigger area.
Available From: The Canada and US Replica Airgun Stores.
Pros:
Drop out stick mags are nice for continuous shooting without having to reload as often.
Has a rail for accessories.
Working slide with blowback action.
Shoots in both semi and full auto selectable.
No CO2 so perhaps better in colder weather being an AEG, lower cost to operate!
Walther licensing via Umarex.
Grip safety to help stop unwanted accidental shots.
Serial number on receiver.
Warning instructions are non-obtrusive.
Trigger is nice and light being an AEG.
Cons:
Is very light weight being almost all plastic.
Low claimed fps and slow full auto cycle rate.
Orange tip.
Sights are all black, harder to see on dark objects
Comments:
The Umarex HK P30 AEG Full Auto Airsoft Pistol is a rather different sort of beast! On one hand it is not what you would expect to see someone using in an Airsoft game but I really don’t think that’s what it is meant for anyway. It’s really just a fun gun for plinking without having to worry to much about safety as if you do something stupid, the consequences will not be too sever! I would say it could possibly be used as an alternate to using a Nerf gun for fun little backyard squishes or shooting indoors. The Umarex HK P30 AEG Full Auto Airsoft Pistol is not for everyone but I am guessing it could be a lot of fun when used in the right situations.
Watch my Table Top Video Review for the Umarex HK P30 AEG Full Auto Airsoft Pistol:
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AR06 & NY03CB. Materials: Mostly all Metal. Weight: 5.6/4.9 pounds (2.5/2.2 kilograms). Length: 27.4-30.7/31.7-35 inches (695-780/805-890mm) Barrel Length: 11/14.6 inch (280/370mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Arcturus AR06 - NY03CB AEG Airsoft Rifles like other AEG Rifles is not mechanical as they are essentially electrical driven so basically the trigger is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed either the Arcturus AR06 - NY03CB AEG Airsoft Rifles or even tried them out yet. I hope to get to my Field Test Shooting Video for both of them later next week, until then we can assume they will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper which they come with claims around 390+fps.
Build Quality: The Arcturus AR06 is a mostly metal with a full metal receiver while the NY03CB has a polymer or plastic receiver which from what I can tell only other components being plastic would be the pistol grips and rear stock. other metal parts on both AR type Airsoft Rifles would be the rail setup, the barrel, the charging handle, the buffer tube, the dust cover, the trigger, the selector switch, the magazine release and bolt release. Fit and finish for both guns is very good.
Realism: The Arcturus AR06 - NY03CB AEG Airsoft Rifles are based on the AR platform with both versions looking the part of a real steel AR. They do come with the removable orange tips installed but they also come with black flash hiders so you can easily switch them out adding to the realism. The metal receiver on the AR06 does give it a bit more weight but even the NY03CB has a decent weight and solid feel to it. Most of the controls work just like a real steel AR including the charging handle, bolt release, selector switch and magazine release.
Pros:
Two versions to meat your budget, both great options.
Quality components throughout both versions. Only real difference is nylon fiber receiver vs metal receiver and slight upgrade motor on AR06 version from Long Type to Long Type 19k torque motor on AR06.
Have been quality control inspected including 5 round recorded fps test with .20 gram Airsoft BB’s.
Both have a functioning bolt catch.
Both come with Quick release two position fully adjustable pop-up sights.
Both come with additional black flash hiders.
Lots of rial mounting options in Picatinny and M-LOK.
6 position adjustable rear stocks.
Easy access to motor for any possible trouble shooting you may need to do.
Additional grip plate option.
Ambidextrous controls and ambidextrous sling mounting points (QD on AR06).
Two magazines come with AR06 (Mid Cap and High Cap).
Cons:
Limited battery options as area is small.
Kind of need a tool to remove rear stock for battery access. (Could change the rear stock)
Mystery accessory baffles me and not mentioned in the manual.
Comments:
Like the AK series of Acturus AEG Airpot Rifles, the Arcturus AR06 - NY03CB AEG are good value for the money with the AR06 offering a slightly higher premium over the lower cost NY03CB. But don’t let the lower price fool you into thinking you are getting a sub-standard product as both versions are built with many of the same components. I personally like the more compact look of the Arcturus AR06 AEG Airsoft Rifle but then again the price of the NY03CB AEG Airsoft Rifle is hard to ignore. Either way you can’t go too wrong so make your pick and enjoy owning one of them.
My Table Top Video of the Acturus AR06 - NY03CB AR AEG Airsoft Rifles:
In this Preview Review Video I take a look at 4 newer products now in our Replica Airguns Online Store. One is a 4.5mm Steel BB Revolver, two are 6mm Airsoft Pistols and one is a .68 caliber Paintball Shotgun.
The first item I take look at in this video is the Umarex HK30 AEG Airsoft Pistol, this product is pretty entry level with analyst all plastic build and is very light to hold. It does however shoot in both semi and full auto since it is an AEG Airsfto Pistol (not many of them out there). The fps is rather low at a claimed fps at just under 200, the Umarex HK30 AEG Airsoft Pistol also comes with two 16 round remove; plastic magazines. Who knows, maybe it will be fun?
Next I take a look at the ASG Dan Wesson 2.5 inch 4.5mm Steel BB Gold Revolver. This is a CO2 powered shell loading BB revolver very much like similar ones I have reviewed in the past but in Gold finish. Will the gold finishes make it perform better, well I guess we better find out!
I then take a look at a “Glock Like” CO2 Blowback Airsoft Pistol for KJWorks called the KP13. It has a full size drop out metal magazine that holds the CO2 along with 24 rounds of 6mm Airsoft BB’s. The KJWorks KP-13 has a metal slide, metal magazine and polymer frame with a velocity over 360fps using the included barrel extension.
Last but perhaps the most interesting for me is the Umarex T4E HDB which is a lower cost Paintball/Rubber Ball Shotgun which could possibly be used for home protection? The T4E HDB is a mostly plastic constructed rifle with decent weight to it and uses an internal spring fed 16 round magazine. You will find all kinds of mounting points for accessories and for a sling on the Umarex T4E HDB and again at much lower cost than similar T4E rifle based Paintball/Rubber ball Airguns.
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AK05. Materials: Mostly all Metal. Weight: 8.2 pounds (3.7 kilograms). Length: 31.1 inches (790mm) Barrel Length: 11 inch (280mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Acturus AK05 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed the Acturus AK05 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK05 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 390+fps.
Build Quality: The Acturus AK05 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK05 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.
Realism: The Acturus AK05 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK05 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.
Pros:
Lots of mounting options: Picatinny rails, M-LOK, AK Side Rail.
Semi and full auto adjustable.
5 position adjustable rear stock.
Mostly metal construction and lots of actual steel including the receiver and dust cover.
Lots of weight to it at 8.2 pounds, feels awesome to hold.
Comes with two magazines, one Hi Cap and one Mid Cap.
Comes with a secondary all black squared off flash hider.
On the fly adjustable rear sight for elevation.
Quick change spring system.
Easy to get to and adjust rotary hop-up adjustment.
Should be good for longer range shooting with nice high claimed fps.
Cons:
Will need a very specific battery type, thin and long.
Rear sight only adjustable for windage and not elevation.
May even be a bit heavy for all day use.
Comments:
The Acturus AK05 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK05 feel realistic and of high quality. If you’re looking for something with a bit more heft than the Acturus AK06 that has a more useful rear stock at least in terms of adjustability and don’t mind giving up some of the compact features of the AK06 then perhaps the AK05 is more for you. IN my opinion the Acturus AK05 AK AEG Airsoft Rifle is a great combination of quality, size and features, hopefully my upcoming Field Test Shooting Review backs up the performance aspect and we can add that to the list.
My Table Top Video of the Acturus AK05 AK AEG Airsoft Rifle:
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AK06. Materials: Mostly all Metal. Weight: 6 pounds (2.7 kilograms). Length: Folded/unfolded 18.9/27.4 inches (480/695mm) Barrel Length: 9.8 inch (250mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Acturus AK06 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed the Acturus AK06 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK06 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 370fps.
Build Quality: The Acturus AK06 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK06 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.
Realism: The Acturus AK06 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK06 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.
Pros:
Lots of mounting options: Picatinny rails, M-LOK, AK/SVD Side Rail.
Semi and full auto selectable.
All metal folding rear stock.
Mostly metal construction and lots of actual steel including the receiver and dust cover.
Lots of weight to it at 6 pounds, feels awesome to hold.
Comes with two magazines, one Hi Cap and one Mid Cap.
Comes with a secondary all black squared off flash hider.
Super compact design.
Quick change spring system.
Easy to get to and adjust rotary hop-up adjustment.
Should be good for longer range shooting with nice high claimed fps.
Cons:
Will need a very specific battery type, thin and long.
Sights are non adjustable.
Folding type rear stock not adjustable for pull length.
Comments:
The Acturus AK06 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK06 feel realistic and of high quality. I also like the compact tactical features of the Acturus AK06 AK AEG Airsoft Rifle making it easy to put in a backpack but not too heavy to lug around all day long. The Acturus AK06 AK AEG Airsoft Rifle also has a decent velocity and fairly fast rate of fire especially when using a higher voltage battery so you can expect excellent performance even from such a small compact AEG Airsoft Rifle.
My Table Top Video of the Acturus AK06 AK AEG Airsoft Rifle:
In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.
This review shows that low cost Airguns can perform just like higher priced Airguns. They may not be as realistic and all made out of metals for that added weight and feel but in terms of power and accuracy they can still get the job done as is with the Umarex NXG CO2 BB Pump Shotgun! In this Field Test Shooting Review I do just that, I test the power and accuracy first by shooting 5 rounds through my Chronograph to find out what the real world fps is, I then I shot 10 rounds down range at a fresh paper target to see what kind of grouping I can get and if the Umarex NXG CO2 BB Pump Shotgun is sighted in on the target out of the box.
Starting with the velocity test I first placed a brand new 12 gram CO2 into the Umarex NXG CO2 BB Pump Shotgun and loaded up the 10 rounds rotary magazine with Daisy Zinc Coated 4.5 mm Steel BB’s. The temperature was around 22 degrees Celsius which is 72 degrees Fahrenheit in the sea can indoor shooting range so not too warm or cold. The claimed fps from Umarex is 450, I was able to get an average of 403fps with the fastest shot hitting 425fps and the slowest shooting down to 388fps. So a bit under the Umarex claimed velocity but in the ball park.
Next I performed the accuracy test for the Umarex NXG CO2 BB Pump Shotgun and since the sights are non adjustable you kind of hope that where you aim is where the shots go but if they don’t then you will need to adjust your aim point just a bit. Out of the box the Umarex NXG CO2 BB Pump Shotgun did shoot a bit low but was fairly bang on side to side so when shooting at around 30 feet out you will need to aim just a tad over the intended target. Out of 10 shots, 8 rounds where all within a nice 1.5 inch grouping with a couple of flyers that I kind of want to keep out of this test because it was probably more me than the gun causing them to go off a bit. 1.5 inches is very good for a 4.5mm Steel BB Airgun!
All in all the Umarex NXG CO2 BB Pump Shotgun shot right around 400fps which is for sure a step up for something like a Red Ryder BB Rifle that at best can shoot 300fps. You also don’t have to work the pump as hard as you would the lever on a Red Ryder since the Umarex NXG CO2 BB Pump Shotgun is CO2 powered rather than spring powered. I also feel like the Umarex NXG Pump Shot was more accurate than the Red Ryder at least for me but that said some people can hit a nickel all day long with their Red Ryders! There are not a lot of Pump Action Looking Airguns out there in 4.5mm Steel BB versions and in more compact easier for younger or smaller shooters so if you fall into that category and want something in a shotgun format then the Umarex NXG CO2 BB Pump Shotgun may be perfect for you.
Trigger Pull: The trigger pull on the Umarex NXG CO2 BB Pump Shotgun is pretty decent, there is a short task up and fairly easy release as the pump action not only turns the rotary magazine but also cocks the internal hammer/striker system. So you will need to pump it before your first shot and after each shot.
Accuracy: I have not Field Test Reviewed the Umarex NXG CO2 BB Pump Shotgun yet but will be making a full Fields Test Review this week to find out what to expect in terms of accuracy and velocity. So we will find out if the fps is closer to the on the box specs of 450 fps or the mostly online specs of 490 fps. Perhaps somewhere in-between?
Build Quality: The Umarex NXG CO2 BB Pump Shotgun is almost all plastic which is not a bad thing in terms of quality and durability. The fact that it only weighs in at 2 pounds may make it feel kind of light and cheap but in a drop or fall situation it means it will most lily not sustain any damage because of the light weight. Most of todays airguns when made out of metals generally are made out of pot metal or zinc alloy which is a nice heavy metal that looks and feels great but is not super strong so when you drop a heavier gun made out of this material it can easily get damaged.
Realism: The Umarex NXG CO2 BB Pump Shotgun looks like a traditional pump action shotgun and even has a little bit of a recessed barrel to make it more believable but it is smaller in size since it is designed more for younger and smaller shooters. The light weight is not only a giveaway but makes ti feel more like a toy than a real gun. If you can ignore that then hopefully you can enjoy the Umarex NXG CO2 BB Pump Shotgun for what it is which is a low cost compact BB rifle made for customs interested in Airguns liek the Red Ryder but that perhaps want a bit more power.
Pros:
Low cost CO2 rifle great for all ages and sizes.
Has a fiber optic front sight.
Comes in a nice looking two tone Black/FDE color scheme.
Fairly easy to pump since the pumping action is not required to activate a spring or compress air.
Built in manual thumb safety.
Stock and high check rest position feel good and a good size length for smaller younger shooters.
Rotary drop out magazine holds 10 4.5mm steel BB’s for quick follow up shots.
Trigger feels pretty good, short and fairly light.
Full ambidextrous design.
Perhaps a step up for entry level shooter over a Red Ryder type BB rifle in terms of power.
Overall a decent looking air rifle.
Cons:
Mostly plastic, so a bit on the light weight side.
Sights are not adjustable in any way.
May be a bit cramped for larger shooters.
Comments: The Umarex NXG CO2 BB Pump Shotgun is not going to win any prizes for quality and realism but keep in mind it is really designed more for entry level younger shooters getting into the Airgun hobby. For them this will be not so intimidating as a larger, heavier more realistic version of a replica Shotgun. I think it will be realistic enough for most new Airgun Shooters and in terms of performance and features it is for sure a step up form something like a Red Ryder BB Rifle. I am looking forward to my upcoming Field Test Shooting Review out what the actual velocity is and what kind of groupings I can get shooting 30 feet down range on a paper target.
My Table Top Video of the Umarex NXG CO2 BB Pump Shotgun:
In this Field Test Shooting Video I test out the BARRA 400e Full Auto AEG 4.5mm BB Rifle to test out the velocity along with the accuracy and also get an idea on what the rate of fire is in Full Auto mode as on the box it claims 550 rounds per minute using what I would assume is a 7.4 volt battery. I wanted to test the BARRA 400e using an 11.1 volt battery but mine died on me. I will more than likely make a short video where I test out the 11.1 volt battery to see how this effects the rate of fire. If you want more information on specifications and details for the BARRA 400e then check my Table Table Video for it here.
Starting with testing out the Velocity for the BARRA 400e Full Auto AEG 4.5mm BB Rifle I shoot 6 rounds through my Chronograph to average out the fps and I was able to average 385 fps which is fairly close to the claimed 410 fps. Temperature does not effect an AEG as no CO2 is being used. Battery voltage also does not effect velocity as long as there is enough voltage to make the AEG motor pull the spring all the way back. Only trigger delay and rounds per minute are effected by battery voltage.
Moving on to my accuracy findings, I loaded up a full 50 round magazine and first unloaded 10 rounds fairly quickly into my paper target setup 30 feet down range shooting from a seated shooting position with the BARRA 400e resting on a sand bag up front. I was impressed to get close to a 1 inch 10 round grouping that placed just a little to the left and down from the bullseye right out of the box. I could easily center the sights as they are fully adjustable. I then switched the BARRA 400e Full Auto AEG 4.5mm BB Rifle to full auto and shot the remaining 40 or so rounds into the same paper target and even though the grouping opened up a little bit, it was not by much so accuracy in semi and full auto is very good with the BARRA 400e.
I have to say the rate of fire on the BARRA 400e Full Auto AEG 4.5mm BB Rifle using a 7.4 volt battery is rather slow even compared to other Airsoft AEG Full Auto Airguns but I still yet have to test it out using a brand new 11.1 volt Lithium battery so I do expect the rate of fire to improve a noticeable amount. Stay posted for that update video. Even with the slower rate of fire from the BARRA 400e this gun is awesome, it is really accurate and the velocity stays super consistent since CO2 cool down is not a factor. The mostly all metal construction and overall quality is very good and the fact that this is really the first commercial AEG 4.5mm Steel BB Rifle makes that alone a great reason to pick one up.
Type:BB Rifle. Manufacturer: BARRA. Model: BARRA 400e. Materials: Mostly Metal with some plastic. Weight: 7.5 pounds (3.4 kilograms). Length: 42.25 inches (1073mm). Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 50 rounds. (1000 shots per battery charge Aprox.) FPS: 410fps. Rate of Fire: 550+ rounds per minute in full auto (depending on battery voltage).
Trigger Pull: The trigger pull on the BARRA 400e AEG Full Auto BB Rifle like other AEG Rifles is not mechanical per say as it is essentially electrical driven so basically it is an on off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back, once the spring is fully drawn back it releases and compresses the air which then propelled the 4.5mm steel BB. The higher voltage battery you use will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire.
Accuracy: I have not Field Test Reviewed the BARRA 400e AEG Full Auto BB Rifle or even tried it out yet as it does not come with a battery or charger and as it uses a Deans connector I will need to get a battery that not only fits this gun size-wise but also has a Deans connector on it. Once I have this battery I will be able to make my Field Test Shooting Video for it. It should have a very consistent velocity since there is no CO2 cool down to factor in so each shot when I Chronograph it should be very similar in fps. I also expect accuracy to be decent since there will not be a lot of recoil as there is no blowback action here.
Build Quality: The BARRA 400e AEG Full Auto BB Rifle is almost all metal in design with an actual CNC machined aluminum hand guard and reciever! It feels very solid when holding it and the fit and finishes are really good. The only plastic I noticed on this AEG styled BB Rifle are the rear stock, pistol grip, and pop-up sights, everything else as far as I can tell are made out of metals.
Realism: The BARRA 400e AEG Full Auto BB Rifle is based on the AR platform in terms of its overall design and looks like a sub variant for sure. It is missing the default forward assist but in all the AIrgun versions of AR typo rifles the forward assist is just for show since there is nothing to assist with an Airgun. Most mechanical parts work as you would expect like the charging handle, magazine release, sectors switch, dust cover and of course the trigger.
Pros:
No CO2 required so cost to shoot is less.
Very consistent velocity as there is no cool down effect from CO2 cooling the gun.
Have the option to shoot in semi or full auto modes.
Almost all metal construction, very solid feeling gun.
Lots of rail option for mounting accessories (Picatinny on the top and M-LOK on sides and bottom).
Flip up sights use a dual mode, when not flipped up you have finer optic lower profile sights, when up there is a post in the front and peep in the back.
6 position adjustable rear stock.
Nice high capacity 50 round magazine, will need more mags for sure since you get 1000 shots per battery charge.
Comes with a speed loader too.
Lots of working parts including the charging handle, dust cover, magazine release, selector switch.
Selector switch is ambidextrous.
Cons:
No blowback operation as with some other Full Auto BB Rifles like the Crosman AR Series.
Does not come with a battery or charger, will need ones that fit and use a Deans connectors.
No red dot included with this version but the iron sights are well thought out.
Comments:
The BARRA 400e AEG Full Auto BB Rifle is something new to the Airgun industry and I always like it when a company doesn’t just make their own version of something we already have in the market and basically just put their branding and licensing on all the same guns. BARRA has made what I believe to be the first AEG 4.5mm Steel BB rifle at least one that has come to market and I always wondered why nobody has tried this before? Well here it is and now we get to see how well an AEG performs with 4.5mm Steel BB’s! Maybe this will start a new market of AEG type 4.5mm Steel BB Guns? I say if it works, well then go for it.
My Table Top Video of the BARRA 400e AEG Full Auto BB Rifle:
In this Preview Unboxing Video I take a look at two full auto BB Machine guns but both very different and both from two separate companies. One is traditionally CO2 operated and the other is AEG operated which is a very new concept for a 4.5mm Steel BB Airgun. I have always wondered why nobody had attempted an AEG 4.5mm Steel BB gun before so here we have the first one to be released…
Starting with the Crosman R1 Fallen Patriots Full Auto CO2 BB Rifle it is essential a re-skinned R1 with a very unique coloration and of course the Fallen Patriots markings on it. The main receiver is a gun metal grey with black and red accents throughout and a purple-blue magazine. It really is stunning to look at and perhaps my favorite Crosman AR series Full Auto BB Gun to date. You do get pop-up Iron sights rather than a red dot which I feel suits this Airgun best and everything else in terms of specifications will be the same as the R1 so check that rifle out for more info.
Now the BARRA 400e is really something new to Steel BB Guns, basically it steals the AEG (Automatic Electric Gun) from what is typically reserved for Airsoft Rifles. I have always wondered why this technology has never been transferred over to 4.5mm Steel BB Airguns? Well now it has with the BARRA 400e Full Auto AEG BB Rifle. According to BARRA you can export to get around 410 fps and that should be super consistent since there is no CO2 cool down effect. You can also shoot in semi or full auto and it has a 50 round magazine that comes with a speed loader for easy loading. Another point to mention is that the BARRA 400e is almost all metal and feels really solid.
In this Field Test Shooting Video I test out the Umarex T4E HDX .68 Paintball Shotgun to find out what the actual fps is and if .68 Caliber Rubber Balls shot out of this Paintball gun are even going to be somewhat accurate at 30 feet out? If you have not already watched my Table Top Video where I go over the details and specifications with some closer up video showing you around the Umarex T4E HDX .68 Paintball Shotgun then make sure to watch it here…
Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 206 fps which may seem slower than expected but they did hit my target pretty hard and actually knocked the cardboard backing right off of it. Each round was fairly consistent ranging from 203 to 210 fps.
Moving on to the accuracy portion of this test I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I managed successfully. I would say most of the rounds all hit within about 5-6 inches of each other which for a Paintball Gun is very good! Keep in mind I was shooting using a seated position with the Umarex T4E HDX .68 Paintball Shotgun rested up front on a sand bag.
All in all the Umarex T4E HDX .68 Paintball Shotgun performed really well shooting consistent velocities and also getting all the rounds on an 8.5 x 11 inch target easily at 30 feet away which means if you where shooting at a persons body area you would easily hit it every shot making this a decent close quarters shooter which is what it really would be used for at the end of the day. Could you use it for less lethal home defense? I guess so especially if you can get your hands on pepper balls but I am not sure if regular rubber or paintballs balls would stop someone? Just seeing this impressive shotgun may in fact be more of a deterrent then being shot by it, but if it get’s the job done then why not.
In this Field test Shooting Video I Test out the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle in the Replica Airguns Indoor Airgun Shooting Range to find out what kind of velocity we can achieve using standard .20 gram Plastic Airsoft BB’s. I also shoot 10 rounds in semi auto at my paper target 30 feet down range to see what kind of grouping I can get and then switch it over to full auto and let her rip till I am basically out of ammo and see if I can punch a nice hole in my cardboard backed target. If you are looking for more details and specification along with some closer up video then make sure to watch my Table Top Review Video for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle.
Starting with my velocity test, I shot 5 rounds through my Chronograph using .20 gram Plastic Airsoft BB’s with the preinstalled spring and got an average of 402 fps with my lowest velocity being 400 and my highest velocity being 405 so really close in fps. You can tone down the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle a bit b y installing the M90 Spring if you find the fps to be a bit high for close quarter battles.
For the accuracy portion of this Field Test Shooting Review I proceeded to fire 10 semi auto rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle resting on a sand bag up front and me sitting on a stool for stability. My 10 shot grouping was all within around 1 to 1.5 inches which is very good for an Airsoft Rifle shooting lighter Plastic BB’s. I then switched the selector into “fun mode” (Full Auto) and proceeded to hold the trigger down until I ran out of spring tension on the High Cap Magazine. I would say I got through around 100+ rounds with most of them making about a 2 inch hole in my target consisting of cardboard and of course the paper target in front of it.
I have reviewed the Specula Arms line of Airsoft Rifles in the past, both the Core and the Edge and they really are great Airsoft Guns. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle as expected lived up to my expectations and performed really great in this Field Test Shooting Video. If you like this model also make sure to checkout the other models Specna Arms Offers over in our Replica Airguns Canada and US Online Stores.
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Core SA-C07-PDW Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: 5.27 pounds ( 2.39 kg). Total Length: 27.2 - 30.3 inches (690 - 770mm). Barrel: 10.63 inch (270) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 380 round magazines. FPS: 380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle, but plan to very soon. You can checkout a previous video where I test out both Specna Arms RRA SA-C10 Core and E10 Edge which should perform similarly to the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is based on the AR15 or M16 platform of course in a very modern and PDW styled look. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such a short PDW styled AR.
Metal V2 Gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you any need to do
Cons:
Plastic receiver.
Need to hold back charging handle to access hop-up.
You will need a very compact battery setup with most Specna Arms models.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line, especially with the Core series. The Specna Arms Core SA-C07-PDW AEG Airsoft Rifle is probably one of my more favorite versions as I really like PDW style compact AR’s in general. You will have to make sure you have on hand a very compact battery as space is extremely limited but other than that one main downside to this style of AEG everything else about it for the money is bang on and worth any slight compromises.
My Vimeo Table Top Review for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle:
Type: Paintball Shotgun. Manufacturer:Umarex - T4E. Model:HDX .68 Paintball Shotgun. Materials: Metal & Polymer. Weight: 6.8 pounds (3.100 kg). Barrel: 16.2 inches (411.5mm) Metal smooth bore. Power Source: 2x12 gram CO2. Action: Pump Action with Internal Magazine. Ammo Type: .68 Caliber Paintball or Rubber Ball. Ammo Capacity: 16 Rounds. FPS: 250-360?
Trigger Pull: The trigger pull on Umarex T4E HDX .68 Paintball Shotgun is a single action only trigger that requires the Pump Action to engage the trigger. Without working the pump the trigger is in the rear portion and does not operate until the Shotgun is pumped, then it pops forward and becomes active. At that point I would say it is fairy short and light, maybe with a little bit of friction but not bad overall. There is also a cross-bolt safety right behind the trigger making it easy to engage and disengage the safety.
Accuracy: So far I have not had the opportunity to test the Umarex T4E HDX .68 Paintball Shotgun but plan a full Field Test Shooting Video shortly. As with most Paintball Airguns they are not going to be super accurate even at 30 feet away. Generally speaking most tests I have done with Paintball guns using rubber balls perform about the same with most of the rubber balls hitting my paper sheet target (8x11) but some even missing completely. In terms of power, on the box Umarex claims 250 fps but I have seen higher velocity specifications on websites including our own so I guess we will find out for sure when I perform my Field Test Shooting Video for the Umarex T4E HDX .68 Paintball Shotgun,
Build Quality: The build quality of the Umarex T4E HDX .68 Paintball Shotgun is very good since this Paintball Shotgun is made for military and law enforcement training use. It has a very good weight and feel to it and has metal parts where you would expect them including the receiver. If you picked this item up along with a real steel Shotgun it would be hard to tell or feel the difference at first inspection.
Realism: The Umarex T4E HDX .68 Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Tactical Styled Pump Action Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.
Expected fairly high fps power of 350+ with .68 caliber paintballs/rubber balls, a bit too high for your average paintball field but perhaps powerful enough to discourage an extruder?
Lots of mounting option for accessories like a tac light, laser or other sighting option with its upper and lower picatinny rail setup.
Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.
Simple to use Cross Bolt Safety.
Nice high capacity 16 round internal magazine.
Dual CO2 offers more shots per CO2 change.
Build quality feels really good, very solid, with lots of weight to it.
Very intimidating looking, just that alone may scare off an intruder.
Cons:
Need a tool to load rounds.
Will not get lots of shots per dual CO2, around 70 or so but not bad.
A bit on the large and bulky side.
Comments:
I am not sure exactly what one would use this Paintball Rifle for but there are a few options. You could use it on the field but with everyone else using high capacity rapid fire Paintball Guns you might be “Out Gunned” to say the least unless of course everyone else was limited in some way to their ammo capacity and rate of fire. Again the Umarex T4E HDX .68 Paintball Shotgun could be used as a non lethal home defense option when combined with the right ammunition type like say some pepper balls? The look of this Shotgun is probably enough to make an intruder get the heck out but I would not count on it. No matter what you plan to use it for it is an awesome Paintball Airgun for sure but just be aware if is not going to be the cheapest option at around $450 Canadian.
I have another Huge Mystery Box to open and share with everyone, this one was even larger and heavier than the last one! You are going to have to watch the video to get all the details on what is actually inside but I can say there are 4 AEG Airsoft Rifles from a new to us company called Arcturus in both AR and AK versions and 2 CO2 Non Blowback Replica Pellet Pistols from KWC.
I do have a some more videos to make from the last Mystery Box Preview being a Specna Arms AEG PDW AR Airsoft Rifle and a Paintball Pump Shotgun that I still need to make both Table Top and Field Test Shooting Video for.
As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.
So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.
Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.
