Type: Pellet Pistol. Distributer:Umarex. Model:Stainless Ruger Mark IV. Materials: Metal and polymer build. Weight: 1.56 pounds (708 grams). Barrel: 5.3 inches (135mm). Total Length: 11 inches (279mm). Propulsion: Spring Piston. Action: SAO Break Barrel. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 1 round. FPS: 320.
Trigger Pull: The trigger pull on the Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis not too bad, I feel it is a around 6-7 pounds or so without measuring. In comparison to a real steel 22LR semi auto SAO trigger pistol, the trigger is much heavier but most of these 22LR pistols of this nature have what I would consider to be near perfect triggers. Over time once you get use to the pressure and release point accuracy with this pistol it is for sure possible.
Accuracy: I have tested out the all black version of this pistol which will perform exactly the same or should I say is expected to perform the same since they are virtually the exact same Pellet Pistol but in different finishes. You can watch my Field Test Shooting Video for the all black version but in case you don’t make it there I will fill you in on the basic results… In terms of velocity I averaged 312 fps using 7 grain lead pellets and got around a 2 inch 7 rounds grouping but expect with a bit more trigger time to get closer to 1 inch.
Build Quality: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistolis a low cost target plinker that also doubles as a licensed Replica for that coolness factor so you won’t get an all metal super top quality build here. That said metal and plastics are well used and for sure details in the fit and finish have been improved over the Buck Mark URX version where I found the barrel felt a bit sloppy and the trigger was plastic. The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol has a much tighter barrel fit when closed and the trigger is now metal! Maybe Umarex watched my video back in the day and took some notes?
Realism: The Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol most resembles the Mark IV Hunter edition and is pretty much bang on in terms of being a replica other than the tell tail hinge just under the barrel required for a spring piston design, there really is no way to get around this so I’m not going to criticize this minor difference. The real steel version is almost 3 pounds and so the pellet shooting version is a bit under weight so it would have been to have had more metal perhaps in the barrel and lower frame. Again since the pellet shooting version is a springer you will not have any working bolts or slide catches or a built in magazine.
Pros:
It's a decent Ruger Mark IV Replica!
Feels well built overall.
Expect it to have really good accuracy like the Umarex Browning Buck Mark URX since they share similar mechanical design.
Barrel locks into place much better than the Umarex Browning Buck Mark URX did.
Fully adjustable rear sight with fiber optic front sight.
Auto locking safety, just don’t forget to unlock before each shot
Actual metal trigger in this version.
Nice and compact, not too heavy.
Full Ruger licensed via Umarex.
Fairly low price tag.
Cons:
No built in rail for a sight system like the Umarex Browning Buck Mark URX.
Would have liked a metal trigger and maybe a slightly lighter trigger pull to match the real Buck Mark's very light trigger pull.
A bit more metal would have been nice.
Significantly more expensive than the black version which is the same exact gun in a different color.
Comments: The Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol is a decent looking replica and a decent pellet shooting target pistol and if you own the real steel version in 22LR you may just want to get your hands on one of these Break Barrel Replica Pellet shooters. The only real question is do you get the Stainless version with simulated wood grips or the all black version? If you like the look of the stainless version and don’t care about money whatsoever, then pickup that one up since it is a Limited Edition version that will only go up in value over time. If you are on a budget and don’t mind the look of the all black versions or maybe even prefer it then by all means grab one since at the end of the day they will both perform exactly the same.
My Vimeo Table Top Review Videos for the Umarex Stainless Ruger Mark IV Break Barrel .177 Cal Pellet Pistol:
This time I have a tiny Mystery Box to unpack and show you guys, this time there are only two pistols, one is a Spring Piston Single Shot .177 Caliber Pellet Pistol and the other is a 6mm Airsoft Blowback BB Pistol, both are Licensed Replicas for Umarex. If you want to find out more about each Air Pistol then make sure to watch this Mystery Box Unboxing Preview Video!
This will be my only video this week as I am in what is called Peak Week in preparation for the Vancouver Fall Calssic Fitness show I am competing in this upcoming weekend. Peak Week really takes a lot out of me and is rather time consuming with the physical activity I am doing and daily blog styled videos I am posting for my other channel www.GetFitOver40.com.
If you are interested in what I do fitness wise then checkout that channel and follow me along this week as I hope to kick some but competing against dudes half my age.
Type: Paintball Shotgun. Manufacturer:Umarex - T4E. Model:HDX .68 Paintball Shotgun. Materials: Metal & Polymer. Weight: 6.8 pounds (3.100 kg). Barrel: 16.2 inches (411.5mm) Metal smooth bore. Power Source: 2x12 gram CO2. Action: Pump Action with Internal Magazine. Ammo Type: .68 Caliber Paintball or Rubber Ball. Ammo Capacity: 16 Rounds. FPS: 250-360?
Trigger Pull: The trigger pull on Umarex T4E HDX .68 Paintball Shotgun is a single action only trigger that requires the Pump Action to engage the trigger. Without working the pump the trigger is in the rear portion and does not operate until the Shotgun is pumped, then it pops forward and becomes active. At that point I would say it is fairy short and light, maybe with a little bit of friction but not bad overall. There is also a cross-bolt safety right behind the trigger making it easy to engage and disengage the safety.
Accuracy: So far I have not had the opportunity to test the Umarex T4E HDX .68 Paintball Shotgun but plan a full Field Test Shooting Video shortly. As with most Paintball Airguns they are not going to be super accurate even at 30 feet away. Generally speaking most tests I have done with Paintball guns using rubber balls perform about the same with most of the rubber balls hitting my paper sheet target (8x11) but some even missing completely. In terms of power, on the box Umarex claims 250 fps but I have seen higher velocity specifications on websites including our own so I guess we will find out for sure when I perform my Field Test Shooting Video for the Umarex T4E HDX .68 Paintball Shotgun,
Build Quality: The build quality of the Umarex T4E HDX .68 Paintball Shotgun is very good since this Paintball Shotgun is made for military and law enforcement training use. It has a very good weight and feel to it and has metal parts where you would expect them including the receiver. If you picked this item up along with a real steel Shotgun it would be hard to tell or feel the difference at first inspection.
Realism: The Umarex T4E HDX .68 Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Tactical Styled Pump Action Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.
Expected fairly high fps power of 350+ with .68 caliber paintballs/rubber balls, a bit too high for your average paintball field but perhaps powerful enough to discourage an extruder?
Lots of mounting option for accessories like a tac light, laser or other sighting option with its upper and lower picatinny rail setup.
Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.
Simple to use Cross Bolt Safety.
Nice high capacity 16 round internal magazine.
Dual CO2 offers more shots per CO2 change.
Build quality feels really good, very solid, with lots of weight to it.
Very intimidating looking, just that alone may scare off an intruder.
Cons:
Need a tool to load rounds.
Will not get lots of shots per dual CO2, around 70 or so but not bad.
A bit on the large and bulky side.
Comments:
I am not sure exactly what one would use this Paintball Rifle for but there are a few options. You could use it on the field but with everyone else using high capacity rapid fire Paintball Guns you might be “Out Gunned” to say the least unless of course everyone else was limited in some way to their ammo capacity and rate of fire. Again the Umarex T4E HDX .68 Paintball Shotgun could be used as a non lethal home defense option when combined with the right ammunition type like say some pepper balls? The look of this Shotgun is probably enough to make an intruder get the heck out but I would not count on it. No matter what you plan to use it for it is an awesome Paintball Airgun for sure but just be aware if is not going to be the cheapest option at around $450 Canadian.
I have another Huge Mystery Box to open and share with everyone, this one was even larger and heavier than the last one! You are going to have to watch the video to get all the details on what is actually inside but I can say there are 4 AEG Airsoft Rifles from a new to us company called Arcturus in both AR and AK versions and 2 CO2 Non Blowback Replica Pellet Pistols from KWC.
I do have a some more videos to make from the last Mystery Box Preview being a Specna Arms AEG PDW AR Airsoft Rifle and a Paintball Pump Shotgun that I still need to make both Table Top and Field Test Shooting Video for.
Starting with my velocity test, I shot 3 rounds through my Chronograph using .177 caliber 7 grain lead pellets achieving 482, 489 and 466 fps with an average of 479 for the three shots. Not bad for a fairly compact Break Barrel Airgun. This is perhaps fast enough for small game like mice and small rats but you would need to get proficient on your shot accuracy to make sure you got a good head or lung shot to make it a more humane pest control.
For the accuracy portion of this Field test Shooting Review I proceeded to fire 6 rounds into a paper target setup 30 feet away. I use a semi rested shooting position with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun resting on a sand bag up front and me sitting on a stool for stability. My 6 shot grouping was all within around 1.5 inches but I feel like this Pellet gun can do better with me getting a bit more use ot it, still not bad out of the box and with my first round shooting it.
I really like the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun as not only a Replica but it also shoed itself ot be a decent target Airgun at the end of the day. I do have to say the trigger is a bit long but not heavy at all, it has a smooth pull with a soft release. Most pimple should be able towel with this just fine. SO if you are looking for a Replica but also want an Airgun that can shoot hard and with decent accuracy then look no further than the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun.
Type:Pellet Rifle. Manufacturer: Umarex Model:HK MP7 .177. Materials: Metal and Polymer. Weight: 4.4 pounds (2kg). Barrel: 11.7 inches (29.7cm). Total Length: 31 inches (78.7cm). Propulsion: Break Barrel Spring Piston. Action: Single Action Single Shot. Ammunition Type: .177 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 490 Claimed.
Trigger Pull: The trigger on the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. The actual trigger pull is pretty decent overall. There is very little take-up but the creep is on the longer side but fairly smooth requiring medium pressure. The release is a bit hard at first to predict but nothing some trigger time can’t get you use to.
Accuracy: I have not performed any shooting tests with the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun so far. I hope to make that Video Review next week. I expect the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun to perform well in the accuracy department especially with the included Red Dot Optical Scope installed. I hope the velocity rating from Umarex is based on lead pellets and not hyper velocity light weight pellets but we will find out the story when I perform my Field Test Shooting Video shortly!
Build Quality: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is a China made Airgun but looks to be well made. It has lots of metal parts as you would expect from a Spring Piston Rifle which adds a nice weight and feel to it. I did however have an issue with the front plastic mock Suppressor/Compensator as it does not seem to be attached to the metal barrel very well other than being pressure fit which is not going to cut it with all the vibration a spring piston system makes. My first shot loosened the mock Suppressor/Compensator so I will either have to hold it when shooting or find another way to make sure it stays in place.
Realism: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is kind of unique in this department as most break barrel rifles are not Replicas, especially the more compact sub machine gun styled ones. Umarex did good job making the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun look like a real HK MP7 for the most part. Of course it is a Spring Piston Rifle at its core so exceptions had to be made to make this work including molded non working parts like the magazine release, sector switch and, bolt/ejection port. That said all in all it is a decent looking replica considering it is a Break Barrel Airgun under the skin.
Pros:
Not many Replica Pellet Rifles on the market, especially in a more compact gun.
Comes with Red Dot sight.
Lots of rails for adding accessories to it.
Full HK Licensed by Umarex.
Collapsible Wire Stock.
Nice high claimed 490 fps.
No need for CO2 so low cost to cooperate.
Not effected by temperature like a CO2 Airgun.
Should have better accuracy than most BB Replica Airguns.
Very solid feel to it, good overall weight and feel.
Cons:
Not going to be an action shooter, have to reload after each shot.
A good overall Replica but not as Realistic or full operation as a BB version would be.
Mock Suppressor/Compensator poorly attached to barrel.
Comments: The Umarex HK MP7 .177 Cal Break Barrel Pellet Gun is an interesting product, on one hadn't it is a Replica Airgun and most people expect a Replica Airgun to have all of the appropriate working parts similar to what would be found on the real steel version. But since this is a Break Barrel Airgun at the core the Umarex HK MP7 .177 Cal Break Barrel Pellet Gun will not function the same as the Real Steel version so as long as you don’t expect it to and appreciate the fact that it should be a nice accurate low cost to operate target rifle then I think you will understand this product and enjoy it for what it is… A Single Shot Pellet Rifle that looks a lot like a HK MP7.
As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.
So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.
Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.
Gun Safeties generally are going to be similar for all types of guns, so Safeties used with Airguns are often the same types as used with Real Steel Guns. Some guns will have no Safeties at all while other guns many have multiple Safeties on them. In this informative video I go over six of the more common types of Gun Safeties used in Real Steel Guns and Air Guns.
Here is a list of the more common types of gun Safeties.
There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.
For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.
So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:
Simple Stick Magazine
Mostly used with Steel BB but also found in some Airsoft Airguns.
Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Full Size Drop Out Magazine
Used with Steel BB and Airsoft guns.
Generally you will find these types magazines hold both the BB’s and CO2.
Used in non-blowback and blowback Airguns.
Commonly used with Airsoft Rifles in mid to high capacity.
Can be made from plastic or steel or a combination of both materials.
Rotary magazine
Used with Steel BB, Airsoft and Pellet Airguns.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel.
Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.
Belt Fed Magazine
Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.
Usually found in a full size magazine that also holds the CO2.
Used in non-blowback and blowback Airguns.
Can be made from plastic or steel or a combination of both materials.
Internal Magazine
Used with Steel BB, Airsoft.
Can have a hopper built in hat feeds a spring fed magazine.
Usually found in lesser expensive Airguns but not a rule.
In this Video I go through each type of Airgun Magazine and talk about their differences and uses.
For this Video 1 Power Test I shoot all of the above listed Airguns first at a pop can, then a soup can and then a toilet paper roll. The ides is to test penetration abilities with the pop and soup can and then raw force shooting the toilet paper as it will absorb all the energy from each airgun round and by gauging how much the toilet paper reacts or moves it should tell us which airgun has the most raw power or energy.
In Video 2 I will be testing accuracy using my standard 30 round paper target setup in the Replica Airguns Sea Can so stay posted for that upcoming video shortly…
In this Field Test Shooting Video I go outside for a bit of a change and test out the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle Combo to see what the real world velocity is and what kind of accuracy I can expect shooting at much further out ranges than my Sea Can Airgun Range offers me. If you want to know more about specifications and details for this Break Barrel Spring Piston Air Riffle make sure to watch my Table Top Video for information along with more closeup video.
Starting with the velocity for the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle Combo, Beeman claims up to 495 fps but does not say weather thesis for the .22 or .177 caliber barrel? I placed 5 rounds through my Chronograph using the .22 Caliber barrel option and was able to average 432 fps using 14.3 grain lead pellets which gave me an energy of 5.93 foot pounds. I would say it is safe to say that you can hit close to the claimed velocity of 495 fps with .22 Caliber lead pellets but would need to be using a bit light grain pellets closer to around 10 or 11 grain. I did not test .177 caliber pellets but they are even lighter and will have an even higher velocity most likely be over 500 fps.
While I was testing velocity to make things more efficient I also placed my shots on a paper target setup around what I estimate to be around 80 feet down range. Now I admit I am not the best long range shooter especially with Spring Piston Air Rifles but I was able to get around a 4 inch grouping at this distance with two shots on top of each other and the other three where more sporadic but I’m pretty sure the spreed was mostly because of my shooting skills with a rifle like this. I was using the provided Beeman 4x30 optical scope for this test rather than the open sights. My pellet choice was .22 Caliber Crosman Premier Hollow Point 14.3 grain lead Pellets.
What I like about the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle Combo is for sure the smooth trigger, the ability to change barrel to either .177 Caliber or .22 Caliber and I like the feel of the stock with its modern look and pistol grip for a comfortable hold. I was not a fan of the 4x30 scope as it seemed a bit fuzzy to me, maybe the optics where off on mine as the other Beeman 4x30 scope that came with the 1042 I tested was super crisp? Lastly I have to say the break barrel on this spring piston does take some arm strength so if you are smaller or not as strong then you may have difficulty cocking the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle Combo. All in all it’s a good overall springer with lots of features for a relatively low cost.
In this Field Test Shooting Video I get outside for a change and test out the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle to see what the actual velocity is and what kind of accuracy I can expect shooting at much further ranges than my Sea Can Airgun Range can offer. If you want to know more about specifications and details for this Break Barrel Air Riffle make sure to watch my Table Top Video for information along with more closeup video.
Starting with the velocity for the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle, Beeman claims up to 475 fps but based on how light the spring feels when cocking this Airgun I was not expecting to get that high of fps. I placed 5 rounds through my Chronograph and was able to average 361 fps using 14.3 grain lead pellets which gave me an energy of 4.14 foot pounds. This isn’t bad in terms of energy but I would not suggest this Air Rifle for pest control because of the lower fps unless you are shooting really small pests at closer ranges.
While I was testing velocity to speed things up I also placed the same rounds on my paper target setup around I would say 80 feet down range (Best guess). Keep in mind I am not the best long range shooter especially with Spring Piston Air Rifles but I was able to get around a 3 inch 5 shot grouping at this distance with three of the shoots all within about 1 inch of each other so not bad for me. I was using the provided Beeman 4x30 optical scope which was nice and crips. My pellet choice was .22 Caliber Crosman Premier Hollow Point 14.3 grain lead Pellets.
What I like about the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle is the easy to cock break barrel, the optical scope, the nice wood finish and its overall performance. I did feel the trigger was a bit heavy and it would be nice to have just a bit more power but that would come at a harder to cock break barrel. If you want an easy shooting and overall good looking lower cost Spring Piston Pellet Rifle in .22 caliber then I would recommend the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle for sure!
Type:Pellet Rifle. Manufacturer: Beeman Model:1042. Materials: Metal and Wood. Weight: 8.7 pounds (3.9kg). Barrel: 16 inches (40.6mm). Propulsion: Spring Piston. Action: Single Action Single Shot. Ammunition Type: .22 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 475 Claimed.
Trigger Pull: The trigger on the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. This will also engage the safety which you have to disengage for each shot manually as an added safety measure. The actual trigger pull is fairly short and light. There is about 2mm of take-up and then a crisp short release with virtually no creep. The trigger is not adjustable but it feels nice as is.
Accuracy: I have not performed any shooting tests with the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle as of yet, I hope to make that Video Review next week “weather permitting” as I want to get outdoors for this test to be able to shoot it at longer ranges. I expect the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle to perform well in the accuracy department using the 4x32 optical scope. In terms of power I did notice that the spring does seem ot be fairly light weight so I am wondering I fi will get close to the claimed 475 fps using .22 caliber lead pellets.
Build Quality: The Beeman 1042 .22 Caliber Break Barrel Pellet Rifle is a China made Air Rifle but looks to be well made. It is mostly metal with a European hardwood stock and feels good to hold resting the rubber butt-pad to your shoulder. I would have lied to have seen the trigger guard being made out of metal rather than plastic.
Realism: The Beeman 1042 .22 Caliber Break Barrel Pellet Rifle is not a copy of any real steel gun in production but does have that overall rifle shape to it so yet it looks like a gun but most people will be able to immediately see that it is a Pellet Rifle and that is exactly what it is since it is not trying to be anything other than that.
Pros:
Nice European hardwood ambidextrous stock.
Ported Muzzle Break is looks goos and may enhance performance a bit.
.22 caliber with close to 500fps so as much energy as you can get without a firearms license in Canada.
Sport trigger with autumn safety system.
Comes with included 4x32 scope and mounts.
Very solid build at 8.7 pounds.
Nice rubber butt-plate looks good and adds to shooting comfort.
Has a scope stop so your scope will stay nicely in place.
Cons:
Does not come with included iron sights.
Really hard to find this exact gun for info, not even on Beeman’s website.
Made in China.
Comments: The Beeman 1042 .22 Caliber Break Barrel Pellet Rifle is a very affordable Break Barrel Spring Piston Pellet Rifle with a really nice European hardwood ambidextrous stock. I like that it has that clean look with no iron sights but rather the included 4x32 optical scope which I am sure will really help with accuracy at further out distances. I hope my Field Test Shooting Video for the Beeman 1042 .22 Caliber Break Barrel Pellet Rifle will do it justice as a target rifle, I am not sure if this one will be any good for pest control as I have my concerns about the fps but will find this out shortly.
Type:Pellet Rifle. Manufacturer: Beeman Model:Longhorn II 10611. Materials: Metal and Polymer. Weight: 8.5 pounds (3.77kg). Barrel: 18 inches (45.7mm). Propulsion: Spring Piston. Action: Single Action Single Shot. Ammunition Type: .177 and .22 Caliber Pellets. Ammunition Capacity: 1. Max FPS: 495 Claimed.
Trigger Pull: The trigger on the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle is single action only requiring you to break the barrel and compress the internal spring piston before you can shoot it. This will also engage the safety which you have to disengage for each shot manually as an added safety measure. The actual trigger pull is pretty good overall. There is very little take-up but the creep is on the longer side but very smooth not requiring too much pressure. The release is also smooth but will take a bit of time to learn just exactly when it is going to release. There is an adjustment screw for the trigger but it is not advertised or explained in the manual exactly how this effects the trigger pull so a bit of trial and error may improve the trigger feel.
Accuracy: I have not performed any shooting tests with the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle so far, I hope to make that Video Review next week “weather permitting” as I want to get outdoors for this test to be able to shoot it at longer ranges. I expect the Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle to perform well in the accuracy department especially with the 4x32 optical scope installed. In terms of power I did notice that the spring does seem ot be fairly strong so I am hoping to get close to the claimed 495 fps even using .22 caliber heavier grain pellets.
Build Quality: The Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle is a China made Air Rifle but looks to be well made. It is mostly metal other than the synthetic modern stock, even the iron fiber optic sights are full metal front and back. I am not a big fan of the stock texture patter but it does work to add extra grip.
Realism: The Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle is not a copy of any real steel gun in production but does have that overall rifle shape to it so yet it looks like a gun but most people will be able to immediately see that it is a Pellet Rifle and that is exactly what it is since it is not trying to be anything other than that.
Pros:
Comes with two barrels for .177 and .22 caliber pellets.
Comes with included 4x32 scope and ring mounts.
Durable synthetic stock with modern look and pistol grip.
Can also shoot using included iron metal fiber optic adjustable sights.
Automatic trigger safety system.
Rated at 495 fps using .22 caliber pellets so top out at max Canada legal power without a firearms license.
Nice rubber butt-pad looks good and adds to shooting comfort.
Has a scope stop so your scope will stay nicely in place.
Really well priced for what you get which is two rifles one.
Cons:
Changing out barrels does require tools.
Not a big fan of the stock texturing pattern.
Made in China.
Comments: The Beeman Longhorn II 10611 .177 .22 Break Barrel Pellet Rifle is a very affordable Break Barrel Spring Piston Pellet Rifle that offers two Airguns in one with it’s interchangeable barrel system allowing you to shoot either .177 or .22 Caliber pellets. You also have the option of using the already installed Fiber Optic fully adjustable sights or you can install the included 4x32 Optical Scope for potential longer range shooting. The modern looking synthetic stock with it’s pistol grip and rubber butt-pad will make shouldering this Air Rifle super comfortable and I would imagine help with accuracy at the end of the day.
In this Field Test Shooting Video for the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol I perform two main tests to find out what the velocity and accuracy capabilities are for it first using my Chronograph and shooting several rounds through it averaging out the fps. For the second test I shoot 7 rounds into a fresh paper target 30 feet down range to see how tight of a grouping I can get.
For my Velocity test Beeman claims the P17 2004 Single Stroke .177 Caliber Pellet Pistol is capable of around 410 fps using standard lead pellets which I found to be a very close estimate as my results using 6.9 grain lead pellets achieved a 4 shot average of 404 fps so only 6 fps off the claim. There are lighter lead pellets out there and even lighter alloy pellets so higher velocities are possible using less grain pellets but a decent grain pellet hitting 400+ fps is not bad considering only one pump is required to get max velocity from the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol.
Moving on to the accuracy portion of the test I setup a fresh paper target 30 feet away and proceeded to put 7 rounds into it shooting from a seated and rested shooting position (sand bag up front, seated in the back). I was a bit surprised to only get a 1.5 inch grouping but it seemed like there where three separate sub groups that each overlapped within themselves? I think perhaps when I pumped the gun I may have been disrupting the rear sight a bit as it does have some play in it for adjustments so you want to be careful not to place your hands on the rear sight when cooking the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol. Out of the box the shot placement was fairly well centered with two of the rounds right dead center of the bulls-eye.
I kind of want to do a retest at some point maybe with a different pellet and also making sure not place my hands over the rear sight when cocking the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol as I feel this Target Pellet Pistol is capable of .5 inch groupings. The trigger is really nice and the rifled barrel is a decent length with easy to use sights so this Air Pistol should do a bit better than I was able to get shooting it on this day. Either way it is a really fun gun to shoot and with a bit of time figuring it out I am confident you can get better results than I did.
Trigger Pull: The Single action only trigger pull on the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol is excellent, super light with just a little bit of take-up, the release is very predictable, one of the best target pistol triggers I have reviewed for sure. There is no adjustment but I do not feel it is nessisary at all.
Accuracy: Spoiler alert! Before posting the written version of this review I did make the Field Test Shooting Video so I can give you a little bit of a heads up on how well the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol in its Field Test Shooting Video. In terms of velocity it was really close to the 410 fps using lead pellets and for accuracy I was pleased with there results but feel the gun can do better than the result I got on this day, perhaps a different pellet choice, some more break in time or maybe just me shooting on a different day. That said I confident this gun is very capable of getting groupings under an inch in the right conditions, maybe even 1/2 an inch.
Build Quality: The build quality of the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol is good considering it is a sub $100 target pistol with a great trigger, fully adjustable fiber optic sights and only one pump to get maximum velocity. The outer shell is polymer while the pump and valve body are aluminum with the barrel and main valve made out of steel. the trigger and latch are also metal.
Realism: The Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol is not really a replica of a real steel gun in production per-say but the pistol grips are very Walther P series looking so if you are Walther owner or like the grips on the Walther P series guns then you will enjoy the hold of the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol.
Pros:
Reasonable price for an accurate full featured target pistol.
Safety automatically resets to the safe position when you pump/charge the pistol.
No need for CO2 so very inexpensive to shoot.
Virtually no recoil or vibration like you find in spring piston airguns.
Fiber optic front and back sight, also fully adjustable for windage and elevation.
Quality materials where you need them for expected long life and use.
Only requires one pump for full 410 fps power.
Works great for left and right handed shooters.
Good if you like Walther type pistol grips, same shape and feel as many P series pistols.
Excellent trigger feel and pull.
Cons:
Loading pellets is a bit awkward.
Have to pump it for each shot, no action shooting here.
Not rally a replica if that’s what you are after but generally most Spring Piston or Pneumatic Airguns are not replicas with a couple exceptions.
Comments: So the Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol is not really a Replica or even an action shooter but it does have its place in an airgun collection. I love blasting pop cans just as much as the next person but sometimes I like to slow things down and see how accurate I can get with an Airgun and not be too concerned that the gun is interfering with the accuracy. This is one way to really improve your shooting skills and having to work for each shot makes it that much more rewarding. The Beeman P17 2004 Single Stroke .177 Caliber Pellet Pistol allows you to have a great time honing in your shooting skills for not a lot of cash up front and cost per shot is only whatever the pellets cost you.
In this Preview Unboxing Video I showcase three Pellet Guns from Beeman, one Single Stroke .177 Caliber Pellet Pistol and two Break Barrel .177 and .22 Caliber Pellet Rifles. I don’t go into a lot of details on each Airgun as I am leaving that information for my future Table Top and Field Test Videos. This video is mainly a heads up on these products with links to where you can buy them in our Online Replica Airgun Store.
In this Field Test Shooting Review I test out the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver in the Replica Airguns Sea Can Indoor Shooting Range to find out its velocity and accuracy using both 4.5mm Steel BB’s and .177 Caliber Lead Pellets. The version I am using is the BB version but my viewers have informed me that the BB version may in fact shoot just as well as the pellet version using pellets even without the rifled barrel due to how pellets are shaped not always requiring a rifled barrel to fly true. So let’s find out!
Starting with the velocity test, I shot 4 rounds of each ammo through my Chronograph using a fresh CO2 cartridge. Umarex claims the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver is able to get a maximum fps of 420 using standard 4.5mm steel BB’s and I was able to average 396 so every close. In warmer conditions 420 fps should be possible. Switching to the .177 caliber lead pellets the fps lowered a bit to an average of 323 fps as expected since the pellets are much heavier (around 7 grain versus 5 grain). I would expect the energy of the pellets to be a bit higher and also keep that energy out to further ranges so if you plan to shoot longer ranges perhaps go with the lead pellets over the BB’s as long as they are similar in accuracy which I test next.
For the accuracy portion of the test I again started off with the 4.5mm Steel BB’s and fired 6 rounds into my paper target setup 30 feet down range. I shot the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 BB Revolver using a seated shooting position with my hands resting up front on a sand bag to help with stability but it’s not perfect and there is always some human factor to consider. That said I was able to shoot a 1.5 inch 6 shot grouping with the BB’s and if I remove one outlier from the group that reduced it to closer to around an inch so not too bad for a BB shooter. I then switching up to the .177 caliber lead pellets and was a bit surprised that even without a rifled barrel the pellets seemed to perform better than the Steel BB’s getting a solid 1 inch grouping with no real outliers in it!
Unfortunately I do not have the actual rifled barrel version of the Umarex S&W M29 8 Inch Barrel Shell Loading CO2 Revolver. Perhaps in the future I can compare the BB verso to the Pellet version using pellets to see if there is an improvement with the addition of the rifled barrel. I can say the BB version without the rifled version shoots pellets just fine at least up to 30 feet so feel free to shoot whatever ammo you want to with it and not be worried about compromising accuracy or velocity.
In this Field Test Shooting Video I put some lead pellets through the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol to see what the real world velocity is compared to the claimed fps. I also put 7 rounds into a paper target setup 30 feet downrange to find out just how accurate and what kind of grouping I can get from this compact spring piston replica air pistol! If you have not already watched my Table Top Review for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol then make sure to watch if for more specifications and details along with some nice close up video.
For my Chronograph test I placed 5 rounds through my Chrony using 8.18 grain Sig Sauer Match Precision Wadcutter Lead Pellets and was able to average 312 fps so just shy of the claimed 320 fps but there are lighter lead pellets out there and even lighter alloy pellets so higher fps can be achieved with this Air Pistol if you plan on using lighter pellets.
For the accuracy portion of my Field test Shooting Video for the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol, I ended up placing 7 rounds into a fresh paper target setup 30 feet down range. I was using my standard seated and rested shooting position which does offer a fairly stable shooting platform but not without some degree of human interaction. I was a little bit disappointed in the 2 inch grouping I got, I was expecting closer to a 1 inch group but I would have had to have been on my game and maybe today I was not. Pellet choice can also effect accuracy for sure and so maybe a different pellet would have performed better in this test. Most of the variable was up and down not left to right with only about an inch side to side.
All in all the Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistol did a good job hitting velocities as claimed and producing a decent grouping that I feel I could have improved upon once I got use to the lighter firmer trigger than I would like to see on a Ruger Mark IV Replica to match the real steal one more closely. Shot placement out of the box was close to the bullseye, it just needed to move up a bit and a tad to the right but once the sights are adjustable for windage and elevation this is easily fixed with a few turns of the sighting screws. If you are a Ruger 22LR owner than I would suggest you buy one of these Umarex Ruger Mark IV Break Barrel .177 Cal Pellet Pistols and shoot for even less cost per shot and in more locations since this Air Pistol is super quiet and most makeshift backstops will work with it just fine.
