Type: BB Machine gun.

Manufacturer:Baikal.

Model:IZH MP-661K.

Materials: Metal & Polymer.

Weight: 3.5 pounds.

Barrel: 8 inches, metal-rifled.

Propulsion: CO2 or (Bulk air with adaptor).

Action: Electronic trigger with 1-3-6 round burst & 300-340-600 Rounds Per Minute.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 30 rounds.

FPS: 360-500.

Trigger Pull: The trigger pull on the IZH Drozd is nice and light due to the fact that the trigger is not mechanical but is instead an electronic on-off switch that operates a solenoid. The solenoid pulsates in turn hitting the CO2 valve release. This is how the single fire and burst fire rates are achieved.

Accuracy: When I was sighting the Baikal Drozd in I got several 5 shot groups well within 1 inch 30 feet out from the target. But when I did my actual video accuracy test, the Drozd did not perform as well, getting more like a 2 inch group, still very reasonable for a gun that can shoot 600 rounds per minute out of the box and 1200 rounds per minute when modified. With metal streaming out the barrel like that you are pretty much going to hit what ever you point it at, the odds are in your favor!

Build Quality: This is a typical Russian made gun, all business and less importance put on looks but even so it is visually appealing, at least to me! Everything works exactly as it should and even though the main shell is plastic it is really a weapons grade polymer so there is no cause for concern here. There are a fair amount of metal components like the factory barrel, most of the magazine and many internal parts.

Realism: Again, the Baikal Drozd IZH MP-661K is not a replica, but it does look like a sub machine gun in many ways, I'm really just not sure exactly what it looks like but when you are shooting this gun you really don't think much about this point because you are too busy grinning!

Purchased From: The Replica Airguns Store.

Pros:

• Very well made BB machine gun.

• Excellent power.

• Good accuracy in all shooting modes.

• Uses the 12 gram CO2 - a bit cheaper! (Can also convert to bulk air)

• Stock version can shoot up to 600 rounds per minute.

• Multiple stock lengths.

• Rifled barrel.

• Adjustable rear sight for windage and elevation.

• Removable magazine hold BB's and CO2.

• Many mods for this gun.

• Great for pest control, especially the ones that don't stay still.

• Made in Russia.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Cons:

• 12 Gram CO2 - you need to change it often!

• Top Accessory rail is a bit short and low.

• Rear stock can get lose sometimes (just add some tape to tighten it up a bit).

Comments:

The Baikal IZH MP-661K is one of the most fun BB machine guns out there and well worth the extra cost to get such a quality product that not only is great out of the box but can also be modified in so many ways to improve it's performance and looks dramatically. Sure the Baikal IZH MP-661K now has a big brother, the Drozd Blackbird, but the Blackbird may be just a bit of overkill for some, I kind of like the Drozd Classics more compact size and if you can't nail what your shooting at with 30 rounds then your doing something very wrong! The Drozd is really the epitome of extreme BB gun weaponry!

My Vimeo Video Review for this Russian made BB Machine gun:

Buy BB Rifles in Canada

Buy BB Rifles in the US

The notorious

Baikal Drozd

is now available in the

Replica Airguns Store

! This is one of the first serious consumer based BB Machine guns made and if you have never seen one in action you need to do so right now! This Russian made Full Auto BB Gun is capable of firing up to 600 rounds per minute and 6 round bursts. Keep in mind that modification chips for this BB shooter are easy to find and make it a 1200 round per minute true full auto shredder.

This well made CO2 4.5mm BB air gun uses a very durable polymer and metal design and takes advantage of an electrically activated trigger for precise aim and consistency.

• 4.5mm Steel BB's
• 30 Round magazine
• CO2 Powered
• Up to 499 fps
• 3.5 Pounds
• 13.75 Inches long
• Rifled barrel
• 300-450-600 rounds per minute selectable
• 1-3-6 round Bursts
• Adjustable rear sight
• Rail for Red Dot Scope (11mm dovetail)
• Metal and polymer design
• Removable stock
• Made in Russia

Buy this gun in Canada

I already have a customized full auto Drozd Blackbird who can pass up another Dorzd when the price is right! I will be making a double Drozd video down the road :)

My new Classic Drozd came with the Full Auto mod chip, the JimC hand made barrel, a 68ci Nitro Duck 4500 PSI carbon fiber tank and bulk air hose.

I also got the Red Dot scope with my new purchase but used one of my rial risers that fit perfectly giving my new Drozd an AR look to it.

Buy Drozd Guns in Canada

Buy BB Guns in the US

Related Posts:

• FULL METAL UZI BLOWBACK CO2 .177 BB GUN ON ITS WAY

• CYBERGUN MINI UZI BB GUN REVIEW

• CYBERGUN MINI UZI CO2 BB GUN CHRONOGRAPH AND FULL AUTO SHOOTING TEST

"Before you attempt to do this modification you need to be aware that it may void your warrantee and/or you may fail and either break something or incorrectly reassemble your Mini UZI rendering it "Broked"! This is your problem so please do not attempt this modification (even though it is fairly easy to do) unless you're 100% confident you can do it and are aware of the possible consequences. Make sure to also take into account any gun laws in your area prohibiting full-auto capable firearms!"

(Special thanks to Herman for showing me the ropes on this modification)

This modification will make your semi-auto "only" Cybergun/KWC Mini UZI BB Gun into a full auto capable 4.5mm BB machine gun. From the factory the full auto switch position (Far Left "A") is disabled but the full auto selector position is visible. The actual full-auto functionality is still present in the Mini UZI but has been decommissioned by the simple means of blocking the selector switch from being moved to the far left full-auto or "A" position.

This full auto modification will show you how to disassemble the Cybergun - KWC Mini UZI BB Gun and remove the small plastic selector switch blockage so you will be able to manually switch between semi auto and full auto modes. This modification takes about 15 minutes to complete.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

You will need the following tools: A pair of pliers and either a pair of small wire cutters or a file.

Let's begin! Below are the two pre-modification positions available from the factory:

"S - SAFE"

"R - SEMI AUTO"

Below is a closeup of the top bolt cover that we will be removing to access the internal bolt for removal:

In the next photo we have removed the bolt cover by pressing the "angled button" towards the rear sight:

And now the bolt is removed:

I removed the grips but this is not necessary:

Now you will need to remove the lower receiver pin located at the back end of the receiver closest to the grip safety. Use a pair of pliers to pinch the metal pin while pushing it through. Once the pin is started you can use the pliers on the other side to pull the pin all the way out. You may need to us a fair amount of force to do this as the fit of the pin is tight:

Once the pin is removed the lower receiver can be detached:

You can see in the picture below the small plastic nub that we will need to remove in order to restore full-auto capability:

I used a pair of small wire cutters to clip this plastic nub off, but you could use a file too. Just make sure that the plastic is flush and does not have any burs or protrusions.

Below is a photo of the Plastic Nub removed from another angle:

After that, all you need to do is reassemble you Mini UZI in revers order to finnish the Full Auto modification.

In the below Photos you can see we have restored the ability to move the fire selector switch over to the "Far Left" or "A" position, reenabling the Cybergun - KWC Mini UZI BB Gun to shoot in full auto when desired.

"A - FULL AUTO"

Now enjoy your Cybergun - KWC Mini UZI BB Gun in full-auto as it was originally designed!

Here is my Vimeo Video in Narrative with Photos:

Buy this gun in Canada

Buy this gun in the US

This Article was graciously provided by one of my viewers: Lee

Related Posts:

• SIG SAUER X-FIVE STAINLESS STEEL VERSION

DISCLAIMER, PLEASE READ AND UNDERSTAND!

• This walkthrough is for information purposes ONLY, if you decide to dismantle your BB gun you will void any warranty you have with the manufacturer.
•  I will not be held accountable for your actions or any damage that is caused by your negligence. Therefore, if YOU decide to dismantle your BB gun and break something during the dismantling or assembling it is your problem not mine.
• If you don’t feel confident or comfortable doing any of these steps STOP and do not proceed any further or you may do damage.
• YOU WILL LOOSE ALL THE SIG SAUER MARKINGS ON THE GUN.

Having said all that, this is my first ever instructional so I’m going to try and make this walkthrough as easy as I can for you to understand. You will need the following: Flat tip Screwdriver for the grips, Small Philips Head screwdriver, small punch & needle nose pliers – the last 2 are optional.

Make sure you have a clean work space and lay out every part in the order that you remove it Left to Right, come reassembly time you work Right to Left it makes reassembly so much easier.

Step 1:

Field Strip the slide until it looks like this:

Unscrew these 2 screws, these hold in the “Breech Block” once your unscrewed cup the end of the slide in your hand and let the Breech & Screws fall in your hand – Set these aside.

That’s it your Slide should look like this:

It is now ready for paint removal.

Step 2:

Take the Frame and start removing the grips Left hand side first:

Flip the frame over and remove the right hand side grips:

Carefully remove the trigger return spring, it is under tension and it WILL fly across the room – I spent an hour looking for it one day! Also while we are at it, you can remove the cover to the magazine release.

To remove the safety, place your flat tip screwdriver between the frame and the safety and twist ever so gently this will separate the safety and all you need to do now is grab the safety from either side and gently pull & wiggle until it separates.

Once the safety is removed you will see the safety bar, this lifts off.

Step 3:

Lift this little pin out and remove the spring, very carefully push this pin from the other side and remove, be careful because once this happens your hammer assembly is loose and free from the frame.

Slowly and gently remove the hammer assembly:

Note the little shiny piece that sits on the side of the hammer assembly, try very hard not to let this piece fly out, it is a pain to get back in, if it does fly out keep calm and take your time, don’t force the little spring in, it seats in behind the shiny metal thing – sorry I don’t have a proper name for it.

Also make sure that the spring next to it is in the locked open position, if it snaps back just get the tip of a small screwdriver and slide it to the left until it locks.

The hammer return spring assembly at the back of the grips can be removed and set aside.

Removing the trigger assembly is easier than it looks; you need to remove the takedown lever by rotating it counter clockwise until it stops.

Push it through the frame and rotate it back clockwise to remove it all together.

Remove the screw holding the trigger assembly:

Lift out the trigger assembly; be careful of the slide lock spring it wont Fly out, but it will fall out.

If you want to remove the magazine release, there is a spring that sits at the rear of the trigger guard;

Push the magazine release in part way & with the flat tip screwdriver lifts the up to remove it, once removed the magazine release will simply fall out.

THAT’S IT! We’re done, ready for the paint removal. Any paint stripper is fine.

KEEP IT WELL AWAY FROM THE PLASTIC PARTS!

Follow the manufacturer’s guidelines for use of their product and thoroughly clean the slide and frame after you have removed the paint.

YOU WILL LOOSE ALL THE SIG Sauer MARKINGS ON THE GUN.

Rub over the slide and frame with #0000 Steel wool or 1200 grit Wet & Dry paper. Clean again and using the paper or steel wool with some ALUMINUM polishing compound like Autosol and some good ol fashioned elbow grease polish the slide and frame until you reach your desired outcome. Clean it all down again and wipe it down with a rag that has had gun oil or my preference “Fluid Film”.

Reassemble the gun in the reverse order and viola one shiny SIG Sauer X-Five.

Buy this gun in Canada   -   Buy this gun in the US

I just noticed that you can get Bulk Air-CO2 Adaptors on Amazon via a company called "Air Venturi". They have them for the Steel Storm, the Drozd and the Blackbird. The Blackbird one actually doubles as a stock mount for your CO2 or Bulk Air Tank.

Buy this gun in Canada   -   Buy this gun in the US