Entries in 380,.68 cal

Umarex T4E HDB .68 Caliber Paintball Shotgun Table Top Review

No Comments

Type: Paintball Shotgun.
Manufacturer: Umarex - T4E.
Model: Umarex T4E HDB.
Materials: Metal & Polymer.
Weight: 5.52 pounds (2.5 kg).
Barrel: 18.5 inches (470.5mm) Metal smooth bore.
Power Source: 1x12 gram CO2.
Action: Semi Auto DOA with Internal Magazine.
Ammo Type: .68 Caliber Paintball or Rubber Ball.
Ammo Capacity: 16 Rounds.
FPS: 220 claimed

Trigger Pull: The trigger pull on Umarex T4E HDB .68 Caliber Paintball Shotgun is basically a Double Action Only Trigger as there is no blowback or way in which to preload a hammer or striker system. So basically your finger does all the work so the trigger pull is I would say about medium length and about medium pull. It does works just fine for fairly rapid follow up shooting. Each pull of the trigger also extends a rear breach-like tube that seals off the CO2 from the internal magazine or there would be a lot of CO2 leakage.

Accuracy: Normally I do not get the chance to perform the Field Test before making my Table Tope Video Review but with the Umarex T4E HDB .68 Caliber Paintball Shotgun, I did it the other way around so I do have performance metrics I can share with you, at least summarized. I suggest watching my Full Field Test Shooting Video Review for the Umarex T4E HDB .68 Caliber Paintball Shotgun for a the full breakdown. In summary, the Umarex T4E HDB .68 Caliber Paintball Shotgun shot a bit low on the target but had a decent grouping of I would say around 4-6 inches which is really good for a Paintball Gun. In terms of power my Chronograph results shooting 5 rounds produced an average of 176fps but the temperature was not super warm so in warmer conditions you can expect this to go up a bit, I would say 200fps is realistic.

Build Quality: The build quality of the Umarex T4E HDB .68 Caliber Paintball Shotgun is really good for the lower price of this unit compared to other higher priced T4E products, you will get a pretty much all plastic outer shell. That said there is still a fair amount of metal in this PaintBall Shotgun including the barrel, internal magazine, sights, trigger, sling mounts and some internal parts. All in all the Umarex T4E HDB .68 Caliber Paintball Shotgun has a good weight and feel to it with nice fit and finish.

Realism: The Umarex T4E HDB .68 Caliber Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Pistol Grip Tactical Styled Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

Pros:

  • Accuracy was really good, probably my tightest grouping so far to date with a Paintball Gun shooting at 30 feet away.

  • Lots of mounting option for accessories like a tac light, laser or other sighting option with it’s top and side picatinny rail and M-LOK setup.

  • Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out over time.

  • Simple to use Cross Bolt Safety.

  • Nice high capacity super easy to load 16 round magazine.

  • Ambidextrous sling mountain points.

  • Low cost for what you get compared to other Umarex/T4E products.

  • Build quality feels pretty good considering it is a much lower cost than other T4E rifles/shotguns.

  • Looks very intimidating.

Cons:

  • Mostly plastic external build.

  • Sights are not adjustable.

  • Will not get lots of shots per single CO2.

  • No rear stock so will not be as accurate using a non rested shooting posting.

Comments:

The Umarex T4E HDB .68 Caliber Paintball Shotgun is a well built and decent performing Paintball Shotgun and for the price you do get a lot of gun for your money. In some ways it even outperforms the HDX in my books including lower price, ease to load, quicker follow shots being semi auto, more compact size and even accuracy was better with the Umarex T4E HDB .68 Caliber Paintball Shotgun. So if you’re on a budget, don’t feel like you are compromising at all here, you are getting a really good Paintball Shotgun solution!

Categories: .68 cal, CO2, Paintball, Pistol, Review, Rifle, Semi Auto, Vimeo Video Tags: Umarex, T4E HDB, T4E

Umarex T4E HDB .68 Caliber Paintball Shotgun Field Test Review

No Comments

In this Field Test Shooting Video I test out the Umarex T4E HDB .68 Caliber Paintball Shotgun to see what the actual fps is and what kind of accuracy we can get out of these .68 Caliber Rubber balls at 30 feet down range. I have not done a Table Top Video just yet for the Umarex T4E HDB .68 Caliber Paintball Shotgun so stay posted for that upcoming video so stay posted for that, in the meantime you can watch my Preview Videos where I do show it up and close and go over some main specifications.

Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 176fps which may seem slower than expected but they did hit my target pretty hard pulling the paper in with them. Each round was fairly consistent ranging from 167 to 182 fps trailing off a bit after each shot which is expected.

Moving on to the accuracy portion for the Umarex T4E HDB .68 Caliber Paintball Shotgun, I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I easily managed. I was impressed with the grouping from the Umarex T4E HDB .68 Caliber Paintball Shotgun as it performed better than most Paintball guns using rubber balls. The shot placement was a bit lower than I was aiming but all the rounds where within I would say 4-5 inches of each other with no real outliers in the grouping.

All in all the Umarex T4E HDB .68 Caliber Paintball Shotgun performed better than I was expecting, I bit more fps would be nice but the rubber balls do hit the paper with a fair amount of energy, I would for sure not want to get hit by one at close range with light clothing on. The accuracy again was really good for a a paintball rifle and this being one of the lower cost Umarex T4E rifle/shotgun based products it performed as good if not better than much higher priced versions. If you’re looking for a fun Paintball Rifle that won’t break the bank and has a good feature set then pick one up for us!

Categories: .68 cal, CO2, Field Test, Review, Rifle, Semi Auto, Vimeo Video Tags: Umarex, T4E, HDB

Umarex HK P30 - T4E HDB - ASG Dan Wesson 2.5 - KJWorks KP13 Update Preview

No Comments

In this Preview Review Video I take a look at 4 newer products now in our Replica Airguns Online Store. One is a 4.5mm Steel BB Revolver, two are 6mm Airsoft Pistols and one is a .68 caliber Paintball Shotgun.

The first item I take look at in this video is the Umarex HK30 AEG Airsoft Pistol, this product is pretty entry level with analyst all plastic build and is very light to hold. It does however shoot in both semi and full auto since it is an AEG Airsfto Pistol (not many of them out there). The fps is rather low at a claimed fps at just under 200, the Umarex HK30 AEG Airsoft Pistol also comes with two 16 round remove; plastic magazines. Who knows, maybe it will be fun?

Next I take a look at the ASG Dan Wesson 2.5 inch 4.5mm Steel BB Gold Revolver. This is a CO2 powered shell loading BB revolver very much like similar ones I have reviewed in the past but in Gold finish. Will the gold finishes make it perform better, well I guess we better find out!

I then take a look at a “Glock Like” CO2 Blowback Airsoft Pistol for KJWorks called the KP13. It has a full size drop out metal magazine that holds the CO2 along with 24 rounds of 6mm Airsoft BB’s. The KJWorks KP-13 has a metal slide, metal magazine and polymer frame with a velocity over 360fps using the included barrel extension.

Last but perhaps the most interesting for me is the Umarex T4E HDB which is a lower cost Paintball/Rubber Ball Shotgun which could possibly be used for home protection? The T4E HDB is a mostly plastic constructed rifle with decent weight to it and uses an internal spring fed 16 round magazine. You will find all kinds of mounting points for accessories and for a sling on the Umarex T4E HDB and again at much lower cost than similar T4E rifle based Paintball/Rubber ball Airguns.

Categories: .68 cal, 4.5mm / .177 cal, 6mm, AEG, Airsoft, BB, Blowback, CO2, Full Auto, Pistol, Review, Revolver, Rifle, Semi Auto, Vimeo Video Tags: Umarex, T4E, HDB, T4E HDB, HK P30, H&K, KJWorks, KP-13, ASG, Dan Wesson

Umarex T4E HDX .68 Paintball Shotgun Field Test Review

No Comments

In this Field Test Shooting Video I test out the Umarex T4E HDX .68 Paintball Shotgun to find out what the actual fps is and if .68 Caliber Rubber Balls shot out of this Paintball gun are even going to be somewhat accurate at 30 feet out? If you have not already watched my Table Top Video where I go over the details and specifications with some closer up video showing you around the Umarex T4E HDX .68 Paintball Shotgun then make sure to watch it here

Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 206 fps which may seem slower than expected but they did hit my target pretty hard and actually knocked the cardboard backing right off of it. Each round was fairly consistent ranging from 203 to 210 fps.

Moving on to the accuracy portion of this test I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I managed successfully. I would say most of the rounds all hit within about 5-6 inches of each other which for a Paintball Gun is very good! Keep in mind I was shooting using a seated position with the Umarex T4E HDX .68 Paintball Shotgun rested up front on a sand bag.

All in all the Umarex T4E HDX .68 Paintball Shotgun performed really well shooting consistent velocities and also getting all the rounds on an 8.5 x 11 inch target easily at 30 feet away which means if you where shooting at a persons body area you would easily hit it every shot making this a decent close quarters shooter which is what it really would be used for at the end of the day. Could you use it for less lethal home defense? I guess so especially if you can get your hands on pepper balls but I am not sure if regular rubber or paintballs balls would stop someone? Just seeing this impressive shotgun may in fact be more of a deterrent then being shot by it, but if it get’s the job done then why not.

Categories: .68 cal, CO2, Field Test, Paintball, Pump, Review, Rifle, Vimeo Video Tags: Umarex, T4E, T4E HDX

Umarex T4E HDX .68 Paintball Shotgun Table Top Review

No Comments

Type: Paintball Shotgun.
Manufacturer: Umarex - T4E.
Model: HDX .68 Paintball Shotgun.
Materials: Metal & Polymer.
Weight: 6.8 pounds (3.100 kg).
Barrel: 16.2 inches (411.5mm) Metal smooth bore.
Power Source: 2x12 gram CO2.
Action: Pump Action with Internal Magazine.
Ammo Type: .68 Caliber Paintball or Rubber Ball.
Ammo Capacity: 16 Rounds.
FPS: 250-360?

Trigger Pull: The trigger pull on Umarex T4E HDX .68 Paintball Shotgun is a single action only trigger that requires the Pump Action to engage the trigger. Without working the pump the trigger is in the rear portion and does not operate until the Shotgun is pumped, then it pops forward and becomes active. At that point I would say it is fairy short and light, maybe with a little bit of friction but not bad overall. There is also a cross-bolt safety right behind the trigger making it easy to engage and disengage the safety.

Accuracy: So far I have not had the opportunity to test the Umarex T4E HDX .68 Paintball Shotgun but plan a full Field Test Shooting Video shortly. As with most Paintball Airguns they are not going to be super accurate even at 30 feet away. Generally speaking most tests I have done with Paintball guns using rubber balls perform about the same with most of the rubber balls hitting my paper sheet target (8x11) but some even missing completely. In terms of power, on the box Umarex claims 250 fps but I have seen higher velocity specifications on websites including our own so I guess we will find out for sure when I perform my Field Test Shooting Video for the Umarex T4E HDX .68 Paintball Shotgun,

Build Quality: The build quality of the Umarex T4E HDX .68 Paintball Shotgun is very good since this Paintball Shotgun is made for military and law enforcement training use. It has a very good weight and feel to it and has metal parts where you would expect them including the receiver. If you picked this item up along with a real steel Shotgun it would be hard to tell or feel the difference at first inspection.

Realism: The Umarex T4E HDX .68 Paintball Shotgun as far as I know is not an exact replica of any specific Shotgun but it does look like what you would expect to see from a Tactical Styled Pump Action Shotgun. In terms of mechanical working parts everything does what it supposed to do and works as expected.

Purchase it from the Canada Replica Airguns Store or the US Replica Airguns Store

Pros:

  • Expected fairly high fps power of 350+ with .68 caliber paintballs/rubber balls, a bit too high for your average paintball field but perhaps powerful enough to discourage an extruder?

  • Lots of mounting option for accessories like a tac light, laser or other sighting option with its upper and lower picatinny rail setup.

  • Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.

  • Simple to use Cross Bolt Safety.

  • Nice high capacity 16 round internal magazine.

  • Dual CO2 offers more shots per CO2 change.

  • Build quality feels really good, very solid, with lots of weight to it.

  • Very intimidating looking, just that alone may scare off an intruder.

Cons:

  • Need a tool to load rounds.

  • Will not get lots of shots per dual CO2, around 70 or so but not bad.

  • A bit on the large and bulky side.

Comments:

I am not sure exactly what one would use this Paintball Rifle for but there are a few options. You could use it on the field but with everyone else using high capacity rapid fire Paintball Guns you might be “Out Gunned” to say the least unless of course everyone else was limited in some way to their ammo capacity and rate of fire. Again the Umarex T4E HDX .68 Paintball Shotgun could be used as a non lethal home defense option when combined with the right ammunition type like say some pepper balls? The look of this Shotgun is probably enough to make an intruder get the heck out but I would not count on it. No matter what you plan to use it for it is an awesome Paintball Airgun for sure but just be aware if is not going to be the cheapest option at around $450 Canadian.

Categories: .68 cal, CO2, Paintball, Pump, Review, Vimeo Video Tags: Umarex, T4E HDX

Replica Airguns Huge Mystery Box Unboxing

No Comments

As the title suggest this a video about a Huge Mystery Box so I am not going to say what’s in it, I can say that their are 4 main products mostly rifles per-say. One is a Futuristic Full Auto BB Rifle, one is a Paintball Shotgun, One is an AEG Airsoft Rifle and one is a Replica Break Barrel Pellet Rifle.

So I have a lot of variety here to show everyone! I did absolutely zero research on any of the products I show in this video since like you I had no real idea what was inside other than how many and that most where rifle based.

Enjoy finding out what new products I will be reviewing over the next month with dedicated Table Top and Field Test Shooting videos.

Categories: .68 cal, 4.5mm / .177 cal, 6mm, Airsoft, AEG, Airgun News, Airsoft News, BB, Blowback, Break Barrel, CO2, Full Auto, Paintball, Pellet, Pump, Replica Airguns News, Review, Rifle, Semi Auto, Single Shot, Spring Piston, Vimeo Video Tags: Umarex, Crosman, Specna Arms, Specna Arms Core, T4E HDS, ST-1, HK MP7, RRA SA-C07-PDW

Umarex T4E HDS Double Barrel CO2 Paintball Shotgun Field Test Review

1 Comment

I don’t do a lot of paintball gun reviews, they just don’t come across my table all that often so it’s a lot fo fun when I do get the chance to shoot some beefier caliber ammunition in the Replica Airguns Sea Can Indoor Airgun Shooting Range. Of course I use rubber ball ammo rather than standard paintball rounds in order to keep the mess to a minimum.

I have not done my Table Top YouTube Video Review yet for the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun but you can checkout a Preview Video for now. In Summary the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a pretty much exactly what the name says. It’s basically a sawn off pistol grip styled double barrel shotgun that uses CO2 and shoots .68 caliber paintballs. You have a selector for shooting either out of the left or right barrel or if you want to can even both at the same time but this really slows down the fps so I would not advise it with the 200 fps version that I was testing with.

Now on to the actual testing of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun! As alway I like to find out how close to the factory claimed fps I will get. Umarex claims around 200 fps for this version which is around 7.5 Joules of energy, apparently there is a 16 Joules version that shoots closer to 300 fps but we do not carry it at least right now. I put a couple fo rounds through my Umarex T4E HDS Double Barrel CO2 Paintball Shotgun using rubber ball paintballs which will be a little bit heavier than a standard paintballs and my first shot yielded 180 fps, my second shot was slightly higher at 184 fps so pretty close to the claimed 200 fps and that was in not the warmest of environments since the temperature in the Replica Airguns Sea Can Indoor Airgun Shooting Range was only 16 Degrees Celsius (60 Degrees Fahrenheit).

Next up it was time to see how the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun performed shooting at a target setup 30 feet away. Since there are no actual sights on the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun I had to kind eyeball it and as I shot it more and more I was able to get my shots closer to the center of the target. The Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is not a tac driver but at 30 feet out you should be able to hit an 8-10 inch target pretty consistently. I don’t recommend using the double shot option since the same amount of CO2 is applied to both rounds that would normally be applied to one round decreasing the fps by about half making the paintball rounds shoot a lot slower and not really being that effective. This may be an option with the higher 300 fps version of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun.

So all in all I had a lot of fun shooting the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun, it’s kind of like a big boy Nerf Gun that you can take onto the paintball field if you wanted to. For home defense I think it is a bit underpowered but there may be a little bit of shock factor that could slow someone down or deter them enough to either give you time get away or take shelter somewhere safe. Maybe using the pepper rounds would work OK in this situation? Either way the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a really cool and unique CO2 Airgun that is not overly expensive and a welcome addition to any Airgun enthusiasts collection.

Categories: .68 cal, CO2, Field Test, Paintball, Review, YouTube Video, Pistol Tags: Umarex, T4E HDS

Umarex T4E HDS Paintball Shotgun and Diana Bandit - Chaser Pellet Pistol Unboxing

No Comments

In this Unboxing Preview video you really can’t get too much different in terms of product types. First up I showcase the Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun. I then take a look at the Diana Bandit PCP and Diana Chaser CO2 Bolt Action Match Grade .177 Caliber Pellet Pistols.

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is a two shot short barrelled that could come in handy for CQB engagements but it looks to be designed also as a none lethal home defence weapon since you can load a CO2 without piercing it but when in a bind you simply hit the CO2 screw and it pierces the CO2 activating the gun for instant use. I will have to test this one out to see if it really has enough power to stop an intrude, after all you only get two shots so they better count!

And then we have two Diana Match Grade CO2 Bolt Action Pellet Pistols, both has a similar bolt, sights, barrel and trigger setup but with the Diana Bandit you get a wooden grips, an included 10 shot rotary magazine and it’s PCP powered so you will need a compressor or a pump to use it. The Diana Chaser on the other hand is CO2 powered, has a plastic pistol grip and does not include the 10 shot rotary magazine but you can buy it later on if you get bored loading one round at a time into the breach. I expect both of these pistols to be tack drivers!

The Umarex T4E HDS Double Barrel .68 caliber CO2 Paintball Shotgun is available in both our Canada and US Online Replica Airgun Store while Both Diana Pellet Pistols can only be found in our Canada Store.

Categories: .68 cal, 4.5mm / .177 cal, CO2, Paintball, PCP, Pellet, Pistol, Review, Rifle, Single Shot, YouTube Video Tags: Umarex, T4E HDS, Diana, Bandit, Chaser

ROHM RG-89 .380 Caliber Blank Revolver Field Test Shooting Review

No Comments

If you haven’t already watched My Table Top Video Review for the ROHM RG-89 .380 Caliber Blank Revolver than make sure to do so for the full features and specifications.

My Field Test Shooting videos for blank guns are pretty basic! I can’t test for accuracy since there is no bullet hitting a target and similarly since there is no bullet I can not test the velocity or feet per second power. SO what is there really left to test?

I guess will the blank gun I am testing fire when I pull the trigger? That’s all there is to really test. You may ask why even make a Field Test Shooting Video for a blank gun if you can’t test accuracy and power. I’ll tell you why… Because it’s just fun and it looks good on camera :)

So watch my YouTube video of me popping of some .380 caliber blanks with my ROHM RG-89 .380 Caliber Blank Revolver inside the Sea Can Airgun Shooting Range.

Categories: Blank Gun, Field Test, Pistol, Revolver, Review, YouTube Video, 380 Tags: ROHM, RG-89

ROHM RG-89 .380 Caliber Blank Revolver Table Top Shooting Review

No Comments

Type: Blank Revolver.
Manufacturer: ROHM (RÖHM).
Model: RG-89
Materials: Mostly Metal.
Weight: 1.45 pounds (658 grams).
Barrel: Front firing designed for attaching a flare adaptor.
Propulsion: Gun powder.
Action: Single & double action.
Ammunition Type: 9mm / .380 caliber crimped.
Ammunition Capacity: 6 rounds.
FPS: N/A.

Trigger Pull: The trigger pull on the ROHM RG-89 .380 Caliber Blank Revolver in single action is fairly light weight with virtually no take up at all as you would expect from a revolver. The double action trigger pull is much heavier with a smooth release. Mechanically the trigger feels really solid.

Accuracy: NA.


Build Quality: The overall build quality for the ROHM RG-89 .380 Caliber Blank Revolver is excellent, being German made its built to last and the fit and finish is typical German quality. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc alloy otherwise know as pot metal with only the moulded grips being made out of plastic.

Realism: The ROHM RG-89 .380 Caliber Blank Revolver is not an exact replica of any given gun in production as this would make importing it into Canada even more difficult, but it is styled after a Snub Nosed type Revolver. As for looking like and working like a real gun, the ROHM RG-89 .380 Caliber Blank Revolver looks and sounds as loud as a real gun, of course with the exception of the dangerous bullet coming out of the barrel!


Purchase from: The Replica Airguns Canada Store

Pros:

  • German made Quality.

  • All metal gun with reenforced steel in some areas.

  • Front firing gun.

  • Large caliber makes a bigger bang.

  • Higher 6 shot capacity over RG-59.

  • Chrome (Silver) finish is very nice.

  • Also like the moulded grips on the Chrome version.

  • Comes with Flare Adaptor & Cleaning Rods.

  • Comes in a nice foam lined plastic hard shell case.

  • Right now Rohm is the only blank gun brand we can get in Canada.

Cons:

  •  Double Action trigger pull is a bit heavy.

  • Have to make sure you only shot them where you will not get in trouble. Very loud!

  • Expensive due to them being harder to get and in high demand in Canada.

Comments:
I think the ROHM RG-89 .380 Caliber Blank Revolver especially in the Chrome (Nickel) version is one of the nicest looking ROHM Blank guns we stock. The additional size over say a ROHM RG-59 makes it feel a lot more beefy in the hand, you also get the extra 6th 9mm / .380 caliber blank with the larger cylinder of the ROHM RG-89 .380 Caliber Blank Revolver. Anther bonus with the Chrome or Nickel version is that you get moulded grips that again I feel looks and fells better in the hand. Along with the ROHM RG-88, the ROHM RG-89 .380 Caliber Blank Revolver is one of my Top ROHM Picks!

My Full Video Review for the ROHM RG-89 .380 Caliber Blank Revolver:

Categories: 380, Blank Gun, Comparison, Pistol, Review, Revolver, YouTube Video Tags: ROHM, RG-89

December Christmas Update Video 2018

No Comments

In this December Update Video I wish everyone a Merry Christmas and Happy New Year. If you have other beliefs and perhaps don’t celebrate Christmas in the traditional Canadian fashion then I wish you a Happy Holiday!

I received a number of products lately and really don’t have time to do full reviews of them as the Holliday season is on us which is going to limit how many videos I can pump out over the next couple of weeks so hopefully this Update video will keep everyone excited about the future Replace Airgun Videos.

Here are the items I talk about in this December 2018 Update Video:

Sig Sauer ASP M17 CO2 Blowback Pellet Pistol

Sig Sauer Fake Suppressor for P226 ASP Pellet Pistol

Umarex Steel Strike Full Auto BB Rifle

ROHM RG-89 .380 Caliber Blank Revolver

Umarex Legends WildCard Airsoft SAA Revolver

Umarex WW2 Limited Edition P08 CO2 Blowback BB Pistol

Umarex WW2 Limited Edition M712 Full Auto CO2 Blowback BB Pistol

Webley Mark VI CO2 Pellet Revolver

John Wayne Signature SAA Revolver Solid Maple Wood Case

Categories: 380, 4.5mm / .177 cal, 6mm, Accessory, Airgun News, Airsoft, Airsoft News, BB, Blank Gun, Blowback, Blank Gun News, CO2, Full Auto, Pellet, Pistol, Replica Airguns News, Revolver, Rifle, Semi Auto, YouTube Video Tags: Sig Sauer ASP

Replica Airguns Silent Auction of Hard to Get Canada Blank Guns

2 Comments

I have some harder to get here in Canada Blank Guns that I am selling from my personal collection by way off Silent Auction. These Blank Guns are more for the Canadian collector and perhaps not so much for the first time buyer. I would recommend for the first time Blank Gun buyer that you checkout our selection off brand new ROHM Blank Guns that we sell in our Canada Replica Airguns Store so check those ROHM Blank Guns out as they are excellent German made Blank Guns in a variety of styles.

Getting back to the Blank Guns in my personal collection. They are all previously owned, most only test fired once for review. Below is a listing of the Blank Guns I am offering in this Silent Auction with what I feel is there approximate value:

Here is how the silent action system works… First of all I will only be shipping these guns within Canada to a Canadian addresses and all funds are in Canadian Funds. You will need to email me and let me know which Blank Gun or Blank Guns you are interested in bidding on and let me know what your best price is. In approximately a weeks time when I feel enough offers have come in, I will then contact the winning bidder and give them 24 hours to pay up. If they do not pay me the amount they offered within the 24 hours I will then move on to the next highest bidder.

If you are bidding on more than one gun then I will take this into consideration since collecting money and shipping product to one buyer is easier than multiple buyers so this will help you with your offer.

I also will be charging $20 for shipping per gun, if you are buying multiple guns then I will discount the shipping a little bit so I will not charge you $20 per gun.

Email me here:

Categories: Silent Auction, YouTube Video, 8mm, 9mm, 380, .22 cal, Blank Gun, Pistol, Replica Airguns News, Semi Auto, Revolver Tags: ROHM, Bruni Mod. 92, EKOL, Aras, ARDA, ARAL, ARAL 622K

Why is My Blank Gun Not Working?

7 Comments

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Categories: .22 cal, 380, 6mm, 8mm, 9mm, Blank Gun, How To, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags:

Mike's Personal Guns For Sale - PAL and Paintball

No Comments

I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing and or buying for myself.

In this second Mike's Personal Guns For Sale video I am offering three rifles, two of which will require a Canada PAL Firearms License since one is a 22LR rimfire rifle and the other is a high powered .22 caliber break barrel pellet rifle. The last item up for bid is an AK-47 styled .68 caliber paintball rifle.

Make sure to watch my above YouTube video to see these three rifles I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.

Here is a list of the these three rifles I am selling from my personal gun collection:

ISSC MK22 22LR (FN SCAR) Rifle - $625 PAL Required

Benjamin Sheridan Super Streak .22 Caliber Break Barrel Rifle $250 PAL Required

Tacamo T68 AK-47 .68 Cal. Paintball Rifle $275

Categories: .22 cal, .68 cal, Break Barrel, Bulk Air, CO2, Paintball, Pellet, Real Gun, Rifle, Semi Auto, YouTube Video Tags: Benjamin Sheridan, ISSC MK22 SCAR 22LR, Super Streak, T68-AK, Tacamo

Mike's Personal Guns For Sale - Blank Guns

1 Comment

I will be showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing.

To start this series off my first video is to highlight the blank guns I am selling, there are only 4 of them, all of which are really hard to get here in Canada so I am not going to let them go cheap. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.

Make sure to watch my above YouTube video to see the blank guns I am selling and instructions on how you can take part in the sale and purchase of them.

Here is a list of the blank guns I am selling from my personal gun collection:

EKOL ASI 9mm Full Auto Front Firing Blank Machine Pistol $725

EKOL Lady Chrome 9mm Front Firing Blank Pistol $400

EKOL Arda 8mm Blank Front Firing Compact Revolver $200

Bruni ME Ranger 1873 SAA .380 Blank Revolver $300

Categories: 380, 8mm, 9mm, Blank Gun, Full Auto, Pistol, Revolver, Semi Auto, YouTube Video Tags: ARDA, Bruni, Colt Single Action Army, EKOL, EKOL ASI UZI, Lady, ME Ranger

Airgun Do’s & Don’ts

No Comments

When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.

Do’s:

  1. Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?

  2. Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.

  3. Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.

  4. Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!

  5. Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.

  6. Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.

  7. Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!

  8. Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.

  9. Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.

Don’ts:

  1. Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.

  2. Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.

  3. Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.

  4. Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.

  5. Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.

  6. Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.

  7. Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.

  8. Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!

Categories: .20 cal, .22 cal, 380, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blank Gun, Blowback, Break Barrel, Bulk Air, CO2, Full Auto, GBB, Gas, Multi-pump, PCP, Paintball, Pellet, Pistol, Repeater, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags:

Top 10 Most Common Airgun Questions and Discussions

No Comments

Categories: .22 cal, .43 cal, .68 cal, 380, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blank Gun, Blowback, Break Barrel, Bulk Air, CO2, Comparison, Full Auto, GBB, Gun Law, Gun Safety, Multi-pump, Non Airguns, PCP, Paintball, Pellet, Pistol, Real Gun, Revolver, Rifle, Semi Auto, Spring Piston, YouTube Video Tags:

ROHM RG-89 & RG-99 Blank Revolver Update Video

6 Comments

We have added some more ROHM 380 Caliber Front Firing Blank Revolvers to the Replica Airguns Canada Store. Here is a quick Vimeo Update Video showing the ROHM RG-89 and ROHM RG-99 side by side with my already reviewed ROHM RG-59 380 Caliber Front Firing Blank Revolver.

ROHM RG-89 & 99 Blank Revolvers.

  • Made by ROHM (Germany)

  • 380/9mm Crimped Blanks

  • 6 Round Cylinder

  • Front Firing

  • Metal with some Steel Parts

  • Come in Hard Shell Case with Cleaning Rod 

Watch my Update Video showing the ROHM RG-89 & RG-99 Front Firing 380 Blank Revolvers:

 
Categories: 380, 9mm, Blank Gun, Pistol, Replica Airguns News, Revolver, YouTube Video Tags: RG-89, RG-99, ROHM

What are the Types of Airguns, Airsoft Guns and Blank Guns?

3 Comments

I wanted to cover some basic Airgun, Airsoft Gun, Blank Gun and Paintball Gun information on what do they all shoot, what makes them shoot and some other miscellaneous info thrown in along the way...

Your should also watch the video attached at the bottom of this post as it goes into a fair amount of detail.

Let's begin with the types of ammo used:

Airgun Ammo

  • Airgun ammo for the most part is broken down into BBs and Pellets, the most standard size BB and Pellet is the 4.5mm or .177 caliber Steel BB and Lead Pellet. You can also get Pellets in other calibers and even other materials other than lead such as steel or aluminum, some can have plastic skirting around a metal interior.

  • Pellets also come in a variety of caliber's like .177, .20. 22. 25 and even larger but then I would start considering them to be bullets as they will take on the shape of a bullet when they get into the larger sizes.

  • Airgun Ammo is not be fired at people, it is primarily used for target and hunting small game.

  • Airguns can use Spring Pistons, CO2, Compressed Air and Multi-pump propulsion systems.

Airsoft Gun Ammo

  • Airsoft Guns for the most part shoot round 6mm (.22 caliber) plastic BBs which come in a variety of weights ranging from .12 grams up to .48 grams. There are larger Airsoft BBs such as 8mm and even larger.

  • There are biodegradable and even tracer florescent Airsoft BBs available.

  • Airsoft Ammo is traditionally used for Airsoft battles and can be fired at people using protective gear. Airsoft Ammo can also be used for target shooting.

  • Airsoft Guns can use Spring Pistons, Spring Piston - AEG (Electric Motor) CO2, Gas (Green, Red, Propane) and Compressed Air propulsion systems.

Paintball Gun Ammo

  • Paintball Guns or "Markers" have been historically used for the sport of Paintball but their whereabouts came from the need of ranchers and forestry workers to mark trees. Hence the name "Marker"

  • Paintball ammo comes in a variety of sizes ranging with the most common being .43 and .68 caliber. They are generally made from a gelatin outer coating containing primarily polyethylene glycol, other non-toxic and water-soluble substances, and dye, they are usually biodegradable.

  • Paintball Guns can also shoot a variety of Paintball Ammo that can be made out of Rubber, Plastic, Glass and they can also contain Powders and even Pepper for use in non lethal defense.

  • Paintball Guns can generally use either CO2 or Compressed Air as their propellant.

Blank Gun Ammo

  • Blank Guns are just like Real Guns but without the dangerous bullet at the end of the brass shell. Other than that they work exactly the same as a Real Gun!

  • Blank Guns are used when a bullet is not required or even wanted. For instance... Gun safety, gun training, training animals to be around guns and/or loud noises, Props for Movies - Stage -  Film - TV, Collectors that do not want the red tape associated with owning a Real Gun or when owning a Real Gun is prohibited.

  • Blank Guns can shoot a variety of sized ammo, most common are .22 caliber crimped, .380 crimped, 8mm P.A.K. and 9mm P.A.K.

  • Blank Guns use gun powder as their means of operation.

Here are the most common forms of propulsion used in the guns we discussed earlier:

CO2

  • CO2 is the most common propellant in Airguns (BB and Pellet), it is also used in Airsoft Guns and Paintball Guns.

  • CO2 is a compressed gas which expands when released, it requires a warm environment to fully expand and tends to cool it's surroundings quickly when shot fast or in full automatic which can slow the velocity of the projectile and even freeze up the gun being used.

  • The most common reusable CO2 cartridges are 12 and 88 gram but you can get larger CO2 tanks in a variety of sizes that can be refilled with CO2.

Gas

  • Gas is used primarily in Airsoft Guns, I have not personally seen an Airgun that is made to use Gas other than CO2.

  • Gas is similar to CO2 in that it is a compressed gas that expands when releases, it also cools down the gun it is being used in and requires a warm environment.

  • Gas comes in a variety of names, Green Gas, Red Gas and Propane Gas. Green Gas contains Propane as it's base but has additives in it like silicone for lubrication .

  • Red Gas is know to be a bit more powerful than Green Gas as it has Chlorodifluoromethane or HCFC-22, R22 or Freon 22 used in refrigeration which turns to a liquid under a slightly higher pressure giving you slightly higher fps.

  • Many people use propane gas with an adapter that allows the mixture of silicone as propane is cheaper to buy.

Compressed Air (HPA)

  • Compressed Air (HPA - High Pressure Air) is most commonly used in Airguns and Paintball Guns but some people use it for their Gas based Airsoft guns.

  • The compressed air comes from high PSI tanks that can be purchased in a variety of sizes and contains compressed air at pressures up to 5000psi.

  • These tanks are reusable and usually need to be refilled at a paintball or scuba shop, some people buy their own compressors or large scuba tanks for refilling purposes.

  • Some Compressed Air (HPA) guns have their own built in tanks that can be filled with a compressor or even a manual pump.

  • Compressed air does not cool down the gun it is being used in and is a great option for high output or fully automatic guns.

Multi-Pump Pneumatic

  • Multi-Pump Pneumatic systems are most commonly used in Pellet and/or BB guns.

  • Multi-Pump Pneumatic guns use the same principle as HPA - High Pressure Air guns in that they require pressurized air as the propellant. The main difference with Multi-Pump Pneumatic guns, is that you do all the work by pumping the gun between shots. Generally speaking you pump the gun 3-10 times, take a shot and repeat this process.

  • Multi-Pump Pneumatic guns are not effected by air temperature and are great for target and small pest control.

Spring Piston

  • Spring pistons are generally found in Pellet Rifles and Pistols but some Airsoft Guns also use a Spring Piston System and generally speaking Spring Piston Guns are single shot only or in other words, the Spring needs to be drawn back before each shot. Spring Piston Guns can have magazines that allow for quicker repeat shots.

  • Spring Piston Guns come in many cocking configurations, Brake Barrel and Side lever to name a couple.

  • The Spring can be a Mechanical Spring or a Gas Spring.

  • Spring Piston Guns are not effected by temperature and are often used for small game hunting and target shooting.

Automatic Electric Guns (AEG)

  • Automatic Electric Guns  are generally found in Airsoft Rifles but there are some Airsoft Pistols (AEP) that use this same system.

  • Automatic Electric Guns use a similar system to a Spring Piston gun but have an electric motor that does all the work of drawing back the spring. You can even have fully automatic AEG guns.

  • The power for the electric motor comes from removable batteries, so it is a combination a battery supplying the motor with the power to draw back the spring that creates a pillow of air that shoots the BB.

  • AEG Airsoft Guns are great for situations when you require high capacity magazines with full auto capability. 

Gun Powder

  • Gun powder is used in Blank Guns, in the same manor that it is used in a Real Gun, the charge from the Gun Powder supplies the force required to operate the blowback in most semi auto Blank Pistols, it also creates the sound of a live round along with the muzzle flash which makes Blank Guns great for training and as Props for Movies and Film.

  • Because the kinetic energy from a blank gun is the same as a real gun, blank guns can be very dangerous when used in close proximity to an object, see my "Are Blank Guns Dangerous Video"!

Some other Gun Relevant Terminology:

Blowback

  • Blowback operation is when some of the force of the propellant is used to move the slide backwards, which in most cases cocks the hammer for single action and can also pickup and chamber a round into the barrel.

  • The slide spring supplies the energy for the return to the forward position of the slide.

  • Blowback Guns do rob some power from the bullet force and in the case of CO2 or Gas Guns the also reduce the amount of shots per CO2 or Gas fill.

Revolver, Semi Automatic

  • Revolver: Revolvers feed ammunition via the rotation of a cartridge-filled cylinder, in which each cartridge is contained in its own ignition chamber, and is sequentially brought into alignment with the weapon's barrel by a mechanism linked to the weapon's trigger (double-action) or its hammer (single-action)

  • Semi Automatic:  semi-automatic pistols use the energy of one shot to reload the chamber for the next. Typically recoil energy from a fired round is mechanically harnessed. After a round is fired, the pistol will cycle, ejecting the spent casing and chambering a new round from the magazine, allowing another shot to take place immediately.

Single Shot, Repeater, Semi Automatic & Fully Automatic

  • Single Shot: A Single Shot Gun needs to be reloaded each time it is shot.

  • Repeater: Repeating action Guns are single barreled guns containing multiple rounds of ammunition. These rounds are loaded from a magazine by means of a manual or automatic mechanism, and the action that reloads the rifle also typically re-cocks the firing action. The term repeating rifle is most often applied to weapons in which the next cartridge is loaded by a manual action, as opposed to semi-automatic rifles, in which the force of one shot is used to load the next.

  • Semi Automatic: A semi-automatic, or self-loading, firearm is a weapon that performs all steps necessary to prepare the weapon to fire again after firing.

  • Fully Automatic: A Gun that uses either its recoil or a portion of the gas propelling the projectile to remove the spent cartridge (in the case of a gun-shell), fire again repeatedly, as long as the trigger is held down or until the magazine is exhausted. Automatic Guns are distinguished from semi-automatic Guns in their ability to fire more than one shot in succession once the trigger is pulled.

Single, Double Action, SA/DA

  • Check out my post explaining Single and Double action!

  • Single-Action (SA): trigger performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled.

  • Double-Action (DA): The trigger both cocks and releases the hammer or striker

  • SA-DA:  A SA/DA firearm combines the features of both mechanisms. You can pull the trigger in Double Action when the hammer is down which cocks and releases the trigger or you can cock the hammer with your thumb and then release the trigger using Single Action to fire the weapon. 

Lever Action, Pump Action, Bolt Action

  • Lever Action: In a classic lever-action firearm, rounds are individually loaded into a tubular magazine parallel to and below the barrel. A short bolt is held in place with an over center toggle action. Once closed, the over center action prevents opening solely by the force on the bolt when the weapon is fired. This toggle action is operated by a hand grip that forms part of the trigger guard. When operated, a spring in the tubular magazine pushes a fresh round into position. Returning the operating lever to the home position chambers the round and closes the breach.

  • Pump Action: With a pump-action firearm, the action is operated by a movable fore-end that goes backwards and forwards to eject, extract, and chamber a round of ammunition. Pump-actions are usually associated with shotguns.

  • Bolt Action: The bolt opens and closes the breech end of the barrel and contains the firing pin. The bolt is held in place with a lever that fits into a notch. Moving this lever out of the notch will release the restraint on the bolt, allowing it to be drawn back. An extractor removes the spent cartridge, which is then ejected through the lever slot. A spring at the bottom of the magazine pushes up the reserve rounds, positioning the topmost between the bolt and the chamber at the base of the barrel. Pushing the bolt lever forward chambers this round and pushing the lever into the notch locks the bolt and enables the trigger mechanism.

Magazine vs Clip

  • Magazine: A magazine is an ammunition storage and feeding device within or attached to a repeating firearm. Magazines can be removable (detachable) or integral to the firearm. The magazine functions by moving the cartridges stored in the magazine into a position where they may be loaded into the chamber by the action of the firearm. The detachable magazine is often referred to as a clip, although this is technically inaccurate.

  • Clip: A clip is a device that is used to store multiple rounds of ammunition together as a unit, ready for insertion into the magazine or cylinder of a firearm. This speeds up the process of loading and reloading the firearm as several rounds can be loaded at once, rather than one round being loaded at a time. The term "clip" is also frequently used to refer to a detachable magazine, though such usage is incorrect.

Categories: .20 cal, .22 cal, .43 cal, .68 cal, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blank Gun, Blowback, Break Barrel, Bulk Air, CO2, Full Auto, GBB, Multi-pump, PCP, Paintball, Pellet, Pistol, Repeater, Revolver, Rifle, Single Shot, Spring Piston, YouTube Video Tags:

Are Blank Guns Dangerous?

10 Comments

One question that comes up often is the danger attached to blank gun use and the most common question I get is about the danger of shooting a blank gun at a person. Blank guns have many uses, one of which is to be used as a prop in a movie or reenactment. In this situation one may want to point and shoot a blank gun at a person to make teh scene more believable it. If the person is far enough away there is usually no cause for concern but with that said I would personally point the gun just off to one side in the event that something might come loose within the gun barrel or perhaps a fragment of something where to be fired and cause an injury to the person the gun is directed towards. With creative camera angles you shouldn't need to actually point a blank gun directly at anyone.

People also assume that because a blank gun does not actually fire a bullet that it is relatively harmless. This is not true at all, in the larger caliber blanks there is about the same amount of energy to what your would find in a real bullet, this is so the blank gun will sound about as loud as a real bullet being fired. The difference with how the energy is released in a blank round versus a real bullet is that the bullet caries most of the energy with it and when the bullet hits its intended target, the bulk of the energy is transferred to that target.

Buy ROHM  Blank Guns in Canada  -  Buy Blank Guns in the US

The energy from a blank round dissipates almost immediately after it leaves the gun barrel but the energy right at the barrel tip is very similar to that of a real bullet, especially if it has nowhere to go but directly into an object. So yes a blank gun round can be lethal at very close ranges and unfortunately several people have paid with their lives finding this out for themselves.

With this newfound information about blank gun danger, some people might say... get rid of these dangers to society! Before we head in that direction think about how many other non vital things we have in our lives that I would have to say have claimed way more lives than blank guns could even come close to: Off-road pleasure vehicles, Skydiving, Skying, Pools, Real Guns to name a few! Blank guns also serve very useful purposes like being used to signal a warning or distress, send out flares, ward off wild animals, train people on how to use a real gun, and of course dog training. I am sure the good outweighs the bad here.

That's enough politics for now, juts watch the video and see for yourself why you should not point a blank gun at anyone, especially if the person is very close in proximity to you!

Categories: .22 cal, 380, 9mm, Blank Gun, Blank Gun News, Field Test, Gun Safety, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: RG-56, RG-59, ROHM