Type: BB revolver.
Manufacturer: KWC (Distributed by Gletcher)
Model: Gletcher CLT-B25.
Materials: Mostly metal with some plastic construction.
Weight: 2 pounds (900 grams).
Barrel: 2.25 inches, non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 rounds.
FPS: 328 fps (120 m/s).
Trigger Pull: The trigger pull on the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC - Gletcher 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.
Accuracy: In terms of power and accuracy, you can checkout my full Field Test Shooting Video here. I did get a nice 2 inch 6 shot grouping on my paper target setup 30 feet away from my standard semi-rested position (sand bag up front and standing in the back). Accuracy was a bit lower than the factory claimed 320 or so fps coming in at an average of 280. I did perform my field test back in May so the weather was not all that warm perhaps effecting peek fps performance somewhat.
Build Quality: The Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.
Realism: The KWC - Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter.
Available in the: Replica Airguns Store.
- It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver
- Mostly all metal design
- lots of detail, well made, fit and finish are both good.
- Good overall weight, even for this short 2.5 inch barrel version.
- Fully adjustable rear sight for windage and elevation.
- Well hidden CO2 Screw.
- Recessed barrel.
- Nice Trigger pull in both single and double action.
- Tactical fingered grips look good and allow for a firm hold.
- Grips are a bit rough, not as rubbery as they look.
- Grips may be a bit large for people with smaller hands.
- All black sights not great on dark backgrounds.
- FPS could be a bit higher!
The Gletcher - KWC CLT-B25 357 2.5 Inch CO2 BB Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel does effect the fps performance since longer barreled versions of this same pistol I have tested do shoot much hotter but that is to be expected with pretty much any short barrelled CO2 pistol.
My YouTube Table Top Review for the Gletcher CLT-B25 357 2.5 Inch CO2 BB Revolver: